AutoDevKit Ecosystem

I needed info on CRC calculation as well.

Hi,I am trying to communicate with BMS IC on our developed board and I donot see the communication happening with BMS IC despite of following all the instructions I have a L9963E BMS Eval board for reference,I have tapped out the SPI frames on the bus to see the dataI could see for the 5 byte of frame data 4 bytes are going first and 2 byte is going after a delay of around 2.2 us when I have fed the SPI  API spi_lld_exchange with 5 bytes the data goes out in one after the other continouslyIs there any specific reason why the data is send in this way?I do not see any speci

I uninstalled my prior Autodevkit 2.1 which seemed to had a lot of trouble with my workspace. The new 2.2 looked promising. A minor bug is that it still shows 2.1 in the About/help section as in the release notes, as on the linked website of the release notes.  But most disturbing: I miss my examples from the application library! If I choose AEK-MCU-C2MLIT1 or SPC58EC I cant see any CAN example. Even if i filter for CAN I get some results of which some dont even contain any CAN. The RLA CAN Test Application for discovery is gone (I used it on 2.1), I can find it when I select SPC58x Gxx - which does not work (UDE can´t get contact and load this onto the board) I also can´t find a example update function or release note what the examples are doing in particular or which UM/release note may walk me through them. How is the usage intended? 

Hi, I just moved from stm32 with Cube IDE into AutoDevKit with an AEK-MCU-C4MLIT1 discovery board. I am so frustrated after a complete 8 hour spin and still no results. Why is AutoDevKit called an IDE when the Debugger is still external? I dont get it. I tried to get it running and found posts heer, 3 years old already stating that the eclipse integration tool does not work anymore. I run into trouble with the external UDE debugger as well, plenty of them. Is there an IDE as CUBE where I can get everything for the SPC controllers? Is there an explanation and code example of simple things like blinking LEDs, hello word kind of things? Or is there a way to run SPC58 in CubeIDE? Tips, suggestions?  

Hi,I tried to make an easy test of this board. when the button sw3 is pushed, LED 2 shall start blinking. Sadly it looks like my if statement equals always 0. Measuring the voltage on the testpin it looks like my MCU is sinking the complete voltage, no matter if the button is pressed or not. How do i configure the GPIO in a way that I could read from it without it to sink all the current? And where do I find this SIUL Documentation I should read before dealing with the advanced settings?  if(pal_lld_readpad(PORT_F, sw3) == 1){pal_lld_togglepad(PORT_F,led2);osalThreadDelayMilliseconds(50);};sw3 = PF13 = Pin84 

Hi everyoneGood day~I have been working on "SPC582Bxx_RLA AEK COM NFC06A1 Key Detection - Trunk System Control" recently and it seems there are several issues that I have encountered:1. The SPI pin OERC needs to be set to "Strong Driver".2. The "platformLog" function doesn't print characters; I need to change it to "printf".3. There was a failure in including "stdio.h", but I have already resolved it.4. Comparing it to the STM32 demo, it appears that "listen mode" might be missing.

Hi,I came across this page stating ST ARCCORE AUTOSAR partnership.https://www.st.com/content/st_com/en/about/media-center/press-item.html/t3796.htmlHow can I get more information about the ST's AUTOSAR solution for AUTOMOTIVE.How Can I use this solution for evaluation. 

I am looking for the autodevkit community- is it here under Automotive? Or did it move somewhere else?

The avbove board comes with a blink example preloaded. I am looking for said example, any suggestions? The preinstalled suggestions seem to target more advanced programs

DearI installed AutoDevkitstudio yesterday.As I can see I should go to this web site"hightec-rt.com/en/" and get a license but in this site there is not any form that I fill it and get a license. Pleas help me more for getting license!. Thank you

This is the sample program I used.This is sounddb.s .When I DEBUG a variable, I find that these pointers point to the same address.I

..

I tried to convert audio files to HEX files，and delete all the lines in the hex file before the starting line of the audio content.Then I program the HEX file to the FLASH, but can't play. I can play with the demo program.Could you tell me how to select an audio file ? Or Provide appropriate demo audio files.

..

Hey, I'm trying to get the AEK-MOT-SM81M1 example project working that is imported from the SPC5STUDIO 6.0 program. Stepper motor used to test is a Lin Engineering 4118l-66pd-01ro bi polar stepper motor.Connections are as follows:SPITP CS connected to D21 on AEK-MCU-C4MLIT1 boardSPITP SDI connected to B34 on AEK-MCU-C4MLIT1 boardSPITP SDO connected to B10 on AEK-MCU-C4MLIT1 boardSPITP SCK connected to D35 on AEK-MCU-C4MLIT1 board SPITP GND connected to A1 on AEK-MCU-C4MLIT1 boardDIOTP EN connected to B21 on AEK-MCU-C4MLIT1 boardVBAT connected to 24v sourcePGND connected to ground of 24v sourceOUTA1 connected to A+ (red wire)OUTA2 connected to A- (blue wire)OUTB1 connected to B+ (green wire)OUTB2 connected to B- (black wire)Software used: SPCSTUDIO v6.0 and UDE STK v5.2Running the program I see that D4 on the AEK-MOT-SM81M1 lights up, but the mot

Hi DearI try to build a test setup with AEK-AUD-D903V1 and AEK-MCU-C1MLIT1 follow the user manual um2719, when I modifed the "application.ld" document, an error was generatered.    .sounddb : ALIGN(16)    {        __sounddb_start__ = .;        *(.sounddb)        *(.sounddb.*)        *(.gnu.linkonce.s.*)            KEEP(*(.sounddb))  // the error line  &nbsp

Hi DearI try to build a test setup with AEK-AUD-D903V1 and AEK-MCU-C1MLIT1 follow the user manual um2719, when I modifed the "application.ld" document, an error was generatered.    .sounddb : ALIGN(16)    {        __sounddb_start__ = .;        *(.sounddb)        *(.sounddb.*)        *(.gnu.linkonce.s.*)            KEEP(*(.sounddb))  // the error line        __sounddb_end__ = .;    } > soundI located the error line, if  "KEEP(*(.sounddb))" line was deleted, the project will be compiled competely, or failed.The error indicator was

Why can't I include the system standard header files? Why can I generate files even if there are problems as long as the console is fine when compiling? Finally, I can burn the program into the chip and run it successfully.

i have set enables 1,2,3 and 4 as 1100 which is address 2 , but for some reason the speaker is not open and voltage is not passing through it which means i cant move on and give orders through i2c registers, can you please explain what the reason might be?

Hi, i have a AEK-AUD-D903V1 evaluation board and i want to make a simple AVAS project. I don't have any board with SPC582Bx microcontroller board. Can I implement this application to stm32 board ? if i can, how should i progress ?

May i know in what library used for push button or the example code for push button?

..

..

Have you already downloaded the latest AutoDevKit release 1.6.0?www.st.com/autodevkitsw#transportation #automotive 

I cannot install this dark theme on SPC5Studio 6.0. Below is the error. Is there any dark theme I could install?Cannot complete the install because one or more required items could not be found. Software being installed: DevStyle (includes Darkest Dark Theme) 1.11.0.202105260439 (com.genuitec.eclipse.theming.core.feature.feature.group 1.11.0.202105260439) Missing requirement: Webclipse UDM 13.0.0.202105260439 (com.genuitec.eclipse.monitor 13.0.0.202105260439) requires 'java.package; org.apache.commons.lang3 3.1.0' but it could not be found Cannot satisfy dependency:  From: EditorMinimap 1.11.0.202105260439 (com.genuitec.eclipse.inlinesearch 1.11.0.202105260439)  To: osgi.bundle; com.genuitec.eclipse.monitor 0.0.0 Cannot satisfy dependency:  From: DevStyle (includes Darkest Dark Theme) 1.11.0.202105260439 (com.genuitec.eclipse.theming.core.feature.feature.group 1.11.0.2021