Automotive and Transportation

Hi. I'm looking for a programmer for SPC564L60L5. The best would seem SPC5-UDESTK but it is not available for sale. Or maybe StellarLINK It will be ok for full programming and debugging support for this chip. Or maybe some other suggestions of a programmer who would support SPC564L60L5?  Thank you for your help Best regards Christopher   

Hi everyone,I am having trouble with the Teoseo VIC3DA GNSS module:My project is using the Teoseo VIC3DA to obtain information about GPS, gyroscope, and accelerometer, but in the default mode, I cannot see any data from the gyroscope or accelerometer. Therefore, I have tried sending the following commands:Tried to read Gyro data$PSTMDRSENMSG,31*<checksum>$PSTMDRSENMSG,30*<checksum>I even tried enabling/disabling the PSTMDRGPS message according to table CDB-ID 228 - NMEA message List 0 with the following commands:$PSTMSETPAR,1228,800000,1 (enable message PSTMDRGPS in current config)$PSTMSETPAR,1228,800000,2 (disable message PSTMDRGPS in current config)=> The Teoseo VIC3DA stil

Are there any C++ Dual Core demos/examples/instructions for using the SPC58EG (or any SPC58 examples) for configuring, initializing and executing?

Hi everyone,I’m working on a project using the SPC58NH92 MCU with SPC5 LLD (RLA) drivers.The setup runs FreeRTOS on Core2 and bare-metal code on Core0.Both cores share data through a dedicated RAM region, with synchronization handled by SEMA4 for access control and cache invalidate/flush operations to maintain data coherence.The application works perfectly when compiled without optimization (-O0). However, when I build with optimization level -O2, the system throws an unhandled exception during runtime.I’m using FreeGCC as the compiler (SPC5Studio environment).Has anyone faced a similar issue on SPC58 multicore systems?Are there any additional recommendations or known considerations regarding shared memory, cache management, or compiler optimization in

Moved  from STM32 forum - this is not an STM32 question.I am facing an issue with the Auto Dev Kit debugger. My previous license had expired (Hightec), and although I tried renewing it and even registered to get a new license, the debugger still does not work.Additionally, I notice that the debugger and flash icons appear greyed out.Could you please assist me in resolving this issue?

I am trying to turn on an LED connected to (PD_9) using the following simple code, but I am encountering an error while flashing the program in UDE. I have attached screenshots of the error and the pin configuration for reference.Code: Simple LED Blinking#include "components.h"/** Application entry point.*/int main(void) {/* Initialization of all imported components (generated automatically). */componentsInit();/* Set PD_9 as output */pal_setpadmode(PORT_D, 9, PAL_MODE_OUTPUT);/* Uncomment the below routine to enable interrupts *///irqIsrEnable();/* Application main loop */for (;;) {pal_setpad(PORT_D, 9); // Turn LED onosalThreadDelayMilliseconds(500); // Delay 500 mspal_clearpad(PORT_D, 9); // Turn LED offosalThreadDelayMilliseconds(500); // Delay 500 ms}}Hardware / Pin Configuration:

Hi allI edited a PCB with TESEO-LIV3F with LNA and RF-AMP on the PCB board.Now I need external passive antenna with Male SMA connector.any recommendations? any one with good experience with this Module that can recommend P.N. for antenna?I attached my design.

Hello, I am trying to use a HighTec Free GCC license with AutoDevKit Studio 2.6.1, but I cannot compile my project. Setup: OS: Windows IDE: AutoDevKit Studio 2.6.1 License: Free GCC Installed compiler: Only VLE compiler (ppc-vle-gcc.exe) is present; ppc-free-gcc.exe is missing Problem: AutoDevKit shows “No license for product (-1)”. Project’s Toolchain Editor only lists the VLE compiler. I am unable to add the Free GCC compiler manually because the executable is not in the installation. Request: Please provide instructions or a link to obtain the PowerPC Free GCC compiler (ppc-free-gcc.exe) compatible with my license. Guidance on installing a

The chip we are using is SR5E1E7. Now we want to know how to perform SWD debugging. We have tried various tools, but none of them worked.

I couldn't find the silk-screen printing instruction document for this model SPC58EG80E5FEC0X. Please help check if these two silk-screen prints are of the same model. Thanks a lot.    

When I use SPC5 Flash Programmer V2.8.1 to connect to the SPC56 CAN programmer, after configuring all the settings and clicking the connect button, the SPC5 Flash Programmer remains in a busy state and fails to establish a normal connection. Could you please tell me how to solve this problem?  Note: The operating system of my computer is Windows 10 64-bit. Besides, when I check the SPC5 Flash Programmer installation Details, it shows that the flash tool plug ins of STMicroelectronics are unsigned, Is this the reason why it cannot work properly? 

Hello,I am trying to run Projects\System\SIUL2\siul2LedBlink from StellarSDK_4.0.0 on a SR6G7EVBC4000P_RevA board. The project was successfully build. To flash the board in RAM, I am using the last version of Lauterbach. When running, it seems that it can't break on main.For testing purposes, I was running the sieve_ram_aarch32_arm_v8r_le.elf using the same Lauterbach script and the execution and breaking on main was done as expected. On a deeper investigation, I have found out that the .elf file form Lauterbach differs from the one build. Those differences can be seen below.

I need the BSDL file (Boundary Scan Description Language ) for SPC560B54L3C6E0X device, but I cannot find it on your web site. Can you send to me?NOTE: This question and answer originated from a customer support case which was handled by us. We regularly review support cases and add any helpful ones here for all to benefit from.

Hello,I have a problem regarding the slow initialization of eth1 on SR6G7 evbc6000 rev B board.The function xNetworkInterfaceInitialise() is failing multiple times, until it is succesfull.  From further investigation, I discovered that phy_check_id() is the cause of the failing. phy_check_id() is used inside dp83tg720_phydev_init(), which can be found here: ModExt/Drivers/Ethernet/DP83TG720/src/dp83tg720.c .Is there something that must be done before initializing the interface? Could it be a problem regarding the Ethernet cable?This behaviour can be seen using StellarSDK 4.0.0, using the ethPing project (Projects/Comms/Ethernet/ethPing). In order to use the eth1, in main() function I also registered the eth1 interface, like this: xNetworkRegisterIf(ETH0_INSTANCE,

Hello, We have two discovery boards with SPC5 automotive MCU - SPC560B-DIS and SPC582B-DIS.We want to use them as basis for testing our hardware, and intend first run the tests with the discovery boards.Where can I find files required for testing regarding these boards - I am looking for SVF, STAPL and BSDL files, can I download them from the website (I failed to find them) or can you send me those files? Thank you in advance,Adam

There are several R52+ cores available in Stellar SR6 P7 line, e.g. SR6P7C8.I have question about the Symmetric Multi-Processing (SMP) support on these R52+ cores. Is SMP available inside R52+ cluster or among R52+ clusters?

I have flashed the application onto the HSM core of SR6G7, and I can see that the HSM core is not running up without a trigger from the Host core. After some analysis, I found that the HSM core requires a power mode change from DRUN mode to RUN mode via the ME_MCTL register. Therefore, I would like to know how we can enable the HSM core to run first by changing the ME_MCTL register value to RUN mode directly, without running the Host core of SR6G7. I want to ensure HSM core running first before host core running. Any help would be appreciated.

I would like to know that, what are the minimum DCF configuration required to activate the HSM core in Stellar SR6G7? Is there any Lauterbach cmm script available to flash the UTEST DCF configuration? 

To enable the HSM notification to application core, I understood that we need to enable HSM2HOST IE register. I would like to know which bit position of 32 bit, we need to enable to make interrupt activate ? There is no such informations in the safety document.   

Hi Team,For SPC58EE84E7QMSAR , Need Port/Pin Mux Functionality / allocation Details for Hardware Software interface specificationThanks,Chetan

Hi,I am using AutoDevKit to develop an application on the SPC563M-DISP. I have a AEK-MCU-SPC5LNK debugger and want to program and debug my software on it. As I know this version only support OpenOCD, but the problem is that I am unable to find the ".cfg" file in the OpenOCD folder, inside the AutoDevKit software.1. Where Can I find the ".cfg" file for the SPC563?2. Can I debug and Program the SPC563 using AEK-MCU-SPC5LNK and OpenOCD?3. Can the AEK-MCU-SPC5LNKU (that uses UDE) program and debug SPC563M-SIP?I currently have the 'SPC5LNK ' and want to use that for developming my app on SPC56, but If that is not possible I can get the SPC5LNKU (UDE version) also, but wants to make sure that I will work.

Hi, I need to change the licensed MAC address for my SPC software.It was previously registered with my Ethernet MAC address, but now I’d like to use my Wi-Fi MAC address instead. Could you please let me know how to update or reissue the license for this change? Thanks in advance!

I want to ask for the schematic and PCB layout advice of the 6.6KW single stage OBC evb which use Stellar as a controller，where can I get this   thanks

I am trying to configure BMS63CHAIN component on AEK-MCU-C4MINI1 board connected to an AEK_POW_BMSNOTX but the allocated pin mapping created by the tool does not match the C4MINI1 board connectors.I tried following the AutoDevKit chapter in um3185 Getting started with AutoDevKit battery management system (BMS) evaluation boards:1. Open AutoDevKit Studio 2.6.12. Create New SPC5 Application using SPC58ECxx Platform Component RLA3. Add SPC58ECxx Init Package Component RLA4. Add SPC58ECxx Low Level Drivers Component RLA5. Add AutoDevKit 4 Mini Init Package ComponentNote: Getting Started guide mentions adding AutoDevKit Init Package, but I can not select this together with 4 Mini Init. Seems to be mutually exclusive.6. Add AEK-POW-BMS63CHAIN component7. Open AEK-POW-BMS63CHAIN -> AEK_POW_BMSCHAIN[0]8. Select Node type: AEK_POW_BMSNOTX9. Seletct dspi: dspi0, cs0Go back to the AEK-POW-BMS63CHAIN

Hello,I have SPC563M-Disp development board, i am trying to flash hex file in it with the help of AEK-MCU-SSPC5LNKU tool. each time i try to connect my board with the SPC5-Flash-programmer it does not respond. Need support