STM32 MCUs Embedded software

Hi,I want to kick ADC1 IN5 with the Timer TIM2. I'm working with CubeIDE.I select:ADC1 -> ADC_Regular_Conversion_Mode -> External Trigger Conversion Source  -> Timer 2 Trigger Out eventTIM2 ->  Trigger Output (TRGO) Parameters -> Update EventBut ADC1 does not run, Data Register is constant.If I kick ADC1 by software everything is fine, I get some noisy numbers.TIM2 is running, the count register is counting.Why does TIM2 not kick ADC1 by the TRGO event?This setup used to work fine on STM32F303. What do I miss on the STM32F429?THX CheersDetlef 

Hi,I am currently facing an issue while connecting to the STM32 board using STM32CubeProgrammer. The tool consistently shows the error: "Unable to read device ID from ROM table."I have already tried the following troubleshooting steps:Performed a hardware/software/core reset using the RESET buttonVerified that all required supply voltages are correctChecked the hardware connectionsDespite this, the programmer is still unable to establish communication with the M7 core via ST-Link. It appears that the device is not being detected properly, and at the moment the board has become unusable.Could you please guide me on possible causes or additional steps I can take to resolve this issue? I would be happy to provide any further information if required.Thank you for your support.Best regards,Prathiksha

I am using the ST Host library version 3.54 on an STM32F769 device, supporting HID devices.  I am using the internal Full Speed phys.I have a USB mouse connected and all works fine, however I would like to save power when the mouse is not being used by putting it into suspend.  I cannot see any support for this in the ST middleware, so I asked Ai and got this:USBH_StatusTypeDef USBH_LL_Suspend(USBH_HandleTypeDef *phost) { HCD_HandleTypeDef *hhcd = phost->pData; USB_OTG_GlobalTypeDef *USBx = hhcd->Instance; uint32_t USBx_BASE = (uint32_t)USBx; USBx->GINTMSK |= USB_OTG_GINTMSK_WUIM; /* Suspend the port */ USBx_HPRT0 |= USB_OTG_HPRT_PSUSP; return USBH_OK; }This works fine - the mouse powers down and there is a useful drop in power consumption.However, I cannot get the port out of standby.  This is the code Ai gave me for the Host to awake the port:

Hello, I wonder that examples could apply Nucleo-H753ZI board... There are some examples about H743 or another one but no example for Nucleo-H753ZI board.    I understand 48k-2channel-16bit can be implemented easily, But I wonder that Nucleo-H753ZI can make 44.1kHz sampling or, 24bit input or, 4 ~ 6 channel input. I can't solve just 48kHz-24bit-2Channel input's buffer underrun problem, 44.1kHz-16bit-2Channel  buffer underrun,  and recognizing USB3300 ULPI to Nucleo-H753ZI. Is it can be done by this board? Or, Is there any spec making limits?   edit: related thread <Nucleo - H753ZI> + <USB3300 ULPI> connecting to P... - STMicroelectr

Hello everyone,I’m working with the STM32U5G9J-DK2 and trying to implement a Bootloader + XIP (Execute-In-Place) application architecture using the external flash.Target setup:A minimal bootloader running from internal flashThe main application linked to and executing from external flash (memory-mapped at 0x90000000)The main motivation is to free internal flash and validate this approach for a future MCU with very limited internal flash.What I’m specifically looking for help withProper CubeMX / .ioc configuration for the bootloaderWhich peripherals must be enabled (RCC, PWR, ICACHE, OSPI, etc.)Which peripherals should not be enabled to avoid conflicts with the XIP appAny STM32U5-specific

STM32G030F6P6 microcontroller CubeIDE environment when enabling interrupt for I2C an LL_I2C_EnableIT_RX (I2C2); error occurs _______stm32g030xx.h:618:29: error: expected declaration specifiers or '...' before '(' token error occurs when any I2C interrupt is enabled  

We are starting to develop a new hardware platform and are currently evaluating the STM32H7R/S series for the main controller.The question now is which RTOS is best suited here in terms of long-term support from ST. We're going to use a lot of communication interfaces (USB, Ethernet, external WiFi/BT module, CAN), an RTOS with an integrated communication stack would make our work easier.Zephyr: High initial training effort, but you get a great framework. The two available H7RS-Eval boards are already supported, but in the video Zephyr 4.1: Status of STM32 support – Erwan Gouriou // Zephyr Meetup Grenoble Mar. 26, 2025 by @Erwan Gouriou from March of this year you can see that Zephyr support for the H7RS is not yet complete. Can anyone give an estimate of the extent to which you can already work with i

I am using the STM32U585RIT6 microcontroller with the B-U585I-IOT02A development kit. I need to implement USB functionality using an interrupt-based approach. In my project, I have configured USB_OTG_FS in Device-only mode, enabled the NVIC global interrupt, and enabled USBX CDC-ACM. I am using bare-metal code (no RTOS or ThreadX). After completing all the USB configurations, inside the MX_USBX_Device_Init() function I added the following initialization: RX FIFO and TX FIFO configurations USBX DCD initialization using _ux_dcd_stm32_initialize() Started the PCD using HAL_PCD_Start() In the main while loop, I am calling ux_device_stack_tasks_run(). With this setup, the USB device starts correctly and is detected as a Virtual COM Port. Now, I want to handle USB connect and disconnect eve

 When using the STM32H743ZI Nucleo board as the I²C master and two STM32 Blue Pill boards as I²C slaves with different addresses, the master requests data from the slaves and the slaves respond accordingly. However, I²C communication  is unreliable during initial startup, and intermittent I²C errors are observed during runtime.Is there anyone to help me with this issue.Thank you.

 

ST‑LINK Mini V3E not detecting STM32H7 (Core ID error, high current when VTARGET connected)I’m debugging an issue with a custom STM32H7 board and an ST‑LINK Mini V3E. The setup includes a main PCB and a separate power PCB. So far:Power & Basic Checks3.3 V and 24 V rails are correct.Board current consumption is low when powered from either an 8 V or 24 V supply.Connections between the ST‑LINK Mini V3E and the main PCB have been verified.ProblemWhen I connect VTARGET from the ST‑LINK to the board’s 3.3 V rail, the current spikes and something starts to smell hot.STM32CubeProgrammer shows no target voltage, no device ID, and fails to read th

Hi everyone,I'm working with an STM32F401CCU6 and trying to transmit 2 bytes over I2C3 using DMA1 Stream 5 Channel 6, which is the correct mapping according to RM0368 Table 28:DMA1 Channel 6 Stream 5 -> I2C3_TXThe DMA configuration appears correct, and I do receive the DMA Transfer Complete (TC) interrupt. So the DMA request is generated, the stream runs, and the transfer completes.However, it seems like the I2C slave device (AW9523) never receives the register and data bytes. Unfortunately my osci is currently broken.The same write sequence works perfectly when I use a blocking I2C write (polling SB, ADDR, TXE, etc.). Only the DMA‑driven version fails.What I observe:START condition is generatedAddress is sent and ACKedADDR flag is cleared correctlyDMA TC interrupt firesSTOP is generatedBut the slave never sees the register or data byteDMA is configured as:

Hello Sir,I urgently want to have an idea whether due to the change of LCD from HT043C KunJjian to RK043FN48H-CT672B Rocktech in 32F746GDISCOVERY Board, is there any changes in the firmware due to this?I would like to request for early response from your team, thanks for your support in advance.Note: From the post only I got a point that RK043FN48H-CT672B Rocktech changed from HT043C KunJjian, 32F746GDISCOVERY B02 and C01 - what's the differen... - STMicroelectronics CommunityBest RegardsSushant Verma

Good day,I've been working for a little on this and can't wrap my head around what the issue is, so figured I'd post here. As a start I'm doing a graduation project from a computer science education and am working on a project that requires a high speed usb to be implemented on a nucleo h755ziq. There are other pieces in play, but those have been disconnected to try and get this one part to work. To make this work I have the nucleo board and a usb3300. This usb3300 has been put on a board and connects to pins placed on the nucleo. I have quadrouple checked the pins and they are all correct. In CUBEMX I setup the USB_OTG_HS external PHY to device mode, as ill be using it as a device which will be detected by an application later in development. 

Hello everyone, I am using a custom board with STM32H750 and I am trying to develop a file system with FILEX. The file system' s media is a uSD card with 10 MB/s baudrate which is communicating with the micro thanks to the SDMMC peripheral. The SDMMC peripheral's configuration is copied from one of the many examples that are available in STMCubeMX ( it has a 50 Mhz clock, 4 bit mode, no power mode save and no transceiver).The uSDcard has been formatted through the api given by FILEX (fx_media_format) following the information available during uSD card initialization ( for example sector size is 512 bytes, number of sectors and so on...).I am using the drivers given by ST for FILEX (in my case SD with IDMA) and I am trying different media size buffer (512, 1024 and 4096) which I allocate in AXI SRAM ( SDMMC1 IDMA can access only in AXI SRAM).I am experiencing two different behaviour:  If I am doing a reading operation the

When using USB CDC to communicate via USART, and interacting with USART data, in code is it recommended to interact with it at the USB side, or to interact with it at the USART side?From what I can tell, both offer both polling and interrupt methods. The USART offers DMA access, but apart from that it's not clear what, if any, tradeoffs there are between USB CDC and USART.

Hello,in our application, running on a H533RET6 and with no TZ enabled, we need to close debug ports in production.I preliminarly did some tests using CubeProgrammer: I generated password-based credentials (obk+bin files, which as far as I understand from AN6008 is the only option when not in TZ) and successfully managed to lock the device by moving from PRODUCT_STATE Open (0xED) to Provisioning (0x17), supplying the .obk file and then lock the device (PRODUCT_STATE = 0x72). After verifying that debug ports were closed, I unlocked the device by making a discovery and providing the bin file, with the device returning into Open state. Note that the first 3 32-bit words of my obk file are:0x00, 0x01, 0xfd, 0x0f, 0x60, 0x00, 0x

I'm trying to enable USART transmission (TX only for now) via DMA, but when I call HAL_UART_Transmit_DMA, the transfer doesn't seem to start at all and HAL_UART_TxCpltCallback is never called.I've configured everything through CubeMX: enabled USART with DMA, enabled FreeRTOS, and enabled interrupts. Without DMA, transmission works fine using HAL_UART_Transmit, but when I switch to HAL_UART_Transmit_DMA, nothing happens.I can't figure out what the problem might be. Does anyone have any suggestions?Here's my main code:/* USER CODE BEGIN Header */ /** ****************************************************************************** * @file : main.c * @brief : Main program body ****************************************************************************** * @attention * * Copyright (c) 2026 STMicroelectronics. * All rights reserved. * * This software is licensed

Hello everyone, I'm having some trouble implementing I3C communication and would like to ask for some help.   I am using the NUCLEO-H503RB board as my main controller. For the target devices, I have the NUCLEO-IKS01A3 expansion board and the TSC1641 (Click Board) connected. I'm currently facing some issues with the I3C communication setup between these components.     I have successfully managed to read the WHO_AM_I ID from the LSM6DSO (on the NUCLEO-IKS01A3). H

I want to make a pedometer app that would count steps and display the number of steps on an LCD screen. I have tested my functions for the screen (ILI9341 SPI), and they work successfully. I tested the LCD code by initializing a timer that incremented the value to display every second and sets the flag update_lcd_flag.But when I add the pedometer code, which uses SPI1, the value on the screen never gets updated past zero. Is it because I launch a DMA interrupt from the timer interrupt, or do I need to look for problems somehwere else, e.g. in my pedometer logic or SPI1 configuration? The pedometer relies on the accelometer, which is built into STM32F4O7G-DISC1, which is my board, by defaultP.S. The LCD functions don't use interrupts or DMA, they only use polling.The timer callbackvoid HAL_TIM_PeriodElapsedCallback(TIM_HandleTypeDef* htim) { if (htim->Instance == TIM2) { if (draw_r

I am migrating from STM32L431 to STM32L471. After migration, the function relating to internal flash writing does not work any more. The problem is when I programmed internal flash with HAL_FLASH_Program(FLASH_TYPEPROGRAM_DOUBLEWORD, address, data), following errors occurred, including FLASH_SR_PROGERR, FLASH_FLAG_PGAERR, and FLASH_FLAG_PGSERR.I searched on the web, and found problem may relate to timer initialization and watchdog usage. I added HAL_TIM_Base_DeInit before HAL_TIM_Base_Init, and watchdog is disabled completely in the system including wathdog initialization and update.. But the problem is still there.By the way, the development environment is MDK5.36, ARM::CMSIS IS 5.8.0 (5.6.0 is also tested), ARM::CMSIS-Driver is 2.6.1, Keil::STM32L4xx_DFP is 2.6.1.So, what the problem it might be, and how can I solve this problem?Thanks

 Hello,I am using an ST7701S LCD over 3-wire SPI (CS, SCK, SDA) with my STM32.When I send the initialization commands from my ESP, I noticed the following:The first command of the sequence is not sent.The program seems to stop at the second stage, around the 100th command.SPI is configured in master mode, polling (no DMA, no interrupts).Example of the write function:void ST7701_Write(uint8_t dc, uint8_t data) { uint16_t value = ((dc & 0x01) << 8) | data; HAL_GPIO_WritePin(LCD_CS_GPIO_Port, LCD_CS_Pin, GPIO_PIN_RESET); HAL_SPI_Transmit(&hspi2, (uint8_t *)&value, 1, HAL_MAX_DELAY); HAL_GPIO_WritePin(LCD_CS_GPIO_Port, LCD_CS_Pin, GPIO_PIN_SET); }Questions:Could the first command being skipped be due to HAL/SPI initialization or state?What is the recommended me

Hello Everyone,I hope this message finds you well. I am currently developing a USB Host application using the STM32H573I-DK and have encountered a persistent Hard Fault issue that I would like to seek your expertise on.[Environment Information]Target: STM32H573I-DKExample: USBPD_SRC_UX_Host_MSC Stack: Azure RTOS (ThreadX, USBX)[Detailed Symptom]A hard fault occurs during initialization or while driving the process thread (msc_process_thread_entry) when connecting a USB MSC device. Debugging revealed abnormal memory access occurring during execution of the _ux_utility

I'm using stm32u535 and would like to have zero crossing detection of supply voltage. I've requirement of 6ADC channels and all are configured in differential mode and adc clock is 25Mhz and resolution is 14 bit and dma circular mode is enabled. On channel 6 i e enabled analog watchdog and written logic in isr to toggle GPIO. I proved gpio and I see deviation. Can someone help here. Here is my code snippet:ADC and AWDG initialization: hadc1.Instance = ADC1; hadc1.Init.ClockPrescaler = ADC_CLOCK_ASYNC_DIV1; hadc1.Init.Resolution = ADC_RESOLUTION_14B; hadc1.Init.GainCompensation = 0; hadc1.Init.DataAlign = ADC_DATAALIGN_RIGHT; hadc1.Init.ScanConvMode = ADC_SCAN_ENABLE; hadc1.Init.EOCSelection = ADC_EOC_SEQ_CONV; hadc1.Init.LowPowerAutoWait = DISABLE; hadc1.Init.ContinuousConvMode = ENABLE; hadc1.Init.NbrOfConversion = 8; hadc1.Init.DiscontinuousCon