STM32CubeIDE (MCUs)

static void MX_ADC3_Init(void){ ADC_ChannelConfTypeDef sConfig = {0};... hadc3.Instance = ADC3; hadc3.Init.ClockPrescaler = ADC_CLOCK_SYNC_PCLK_DIV4; hadc3.Init.Resolution = ADC_RESOLUTION_12B; hadc3.Init.ScanConvMode = ADC_SCAN_ENABLE; hadc3.Init.ContinuousConvMode = DISABLE; hadc3.Init.DiscontinuousConvMode = DISABLE; hadc3.Init.ExternalTrigConvEdge = ADC_EXTERNALTRIGCONVEDGE_RISING; hadc3.Init.ExternalTrigConv = ADC_EXTERNALTRIGCONV_T5_TRGO; hadc3.Init.DataAlign = ADC_DATAALIGN_RIGHT; hadc3.Init.NbrOfConversion = 1; hadc3.Init.DMAContinuousRequests = DISABLE; hadc3.Init.EOCSelection = ADC_EOC_SINGLE_CONV; if (HAL_ADC_Init(&hadc3) != HAL_OK)... sConfig.Channel = ADC_CHANNEL_4; sConfig.Rank = ADC_REGULAR_RANK_1; sConfig.SamplingTime = ADC_SAMPLETIME_3CYCLES; if (HAL_ADC_ConfigChannel(&hadc3, &sConfig) != HAL_OK)... /* USER CODE END ADC3_Init 2 */-----------------------------------static void MX

Hello Everybody I have the Problem with my Hightimer PWM Output. If I define that my HRTIM is working with 480MHz (CPU_Ck). it will not and work with the normal 240MHz Output.Why is that so?

Hi there!I've just started working with STM32CubeIDE and after a bit of a vertical learning curve I'm slowly getting to grips with most aspects of it.I want to DMA to GPIO and there doesn't appear to be any way to do this through the .ioc GUI interface. GPIO ports can't be targeted as a peripheral by the DMA interface, and when you select a MemToMem option in the DMA section, the code that is generated by STM32CubeIDE doesn't have any user sections, and is hence effectively not able to be edited by the user.The other issue is that the MemToMem DMA option doesn't expose the most useful options like "circular" mode (it only exposes "normal") and doesn't give the option to provide any triggers either.Have I hit the limits of what STM32CubeIDE is able to do already? or is there some way to achieve this through the STM32CubeIDE interface that I haven't yet seen?BTW FWIW I'm using the very very latest release of STM32CubeIDE.Thanks,Luke

I want to know how to fold curly braces. There are too many codes in the interface, so i hope the brace can be folded.

I am trying to use the SD card slot on the ST32F746 Discovery board. I am using the default project that is generated by STM32CubeIDE which includes MX_FATFS_Init() to set up the SD card. I have made no changes and used the default settings for everything except the StartDefaultTask method.In my StartDefaultTask method I am trying to use the SD card similar to STM32CubeF7 Firmware Package:void StartDefaultTask(void const *argument) { /* init code for USB_HOST */ MX_USB_HOST_Init(); /* USER CODE BEGIN 5 */ FIL MyFile; /* File object */ uint8_t workBuffer[_MAX_SS];   FRESULT res; /* FatFs function common result code */ uint32_t byteswritten, bytesread; /* File write/read counts */ uint8_t wtext[] = "This is STM32 working with FatFs"; /* File write buffer */ uint8_t rtext[100]; /* File read buffer */   /*##Register the file system object to the FatFs module ##############*/ if (f_mount(&SDFatFS, (TCHAR const*) SDPath, 1) != FR_OK) { ...f_mount gets stuck since sd_

I am using STM32G071 Nucleo Board, but this is also the case when I only use the uC IC and not Nucleo Board.I am using CubeIDE and HAL programming.Below is the link to the Nucleo board:https://www.st.com/content/ccc/resource/technical/layouts_and_diagrams/schematic_pack/group0/89/90/f2/80/b8/a8/49/6d/MB1360-G071RB-C01_Schematic/files/MB1360-G071RB-C01_Schematic.pdf/jcr:content/translations/en.MB1360-G071RB-C01_Schematic.pdf

When I set Output compare preload to enable in the configuration interface, the generated code shows disable

I'm working in STM32 CubeIDE with a Blue Pill board.To control the size of main.c I have gathered groups of functions together in to several c/h pair files. One of the pairs is 'myirqcallbacks.c/h". At the moment I have two UART IRQs and an external pin IRQ callback in this c/h pair.The UARTs work fine but the EXT IRQ fails to call my code. It runs the __weak copy in stm32f1xx_hal_gpio.c instead.When the code was in main.c it ran OK.It seems that the compiler can't see my EXT IRQ callback function so fails to deprecate the __weak copy of the callback. It can however see the two UART callback functions in there. Is there some difference in the structure of the GPIO and UART IRQs?myirqcallbacks.h/* * myirqcallbacks.h * * Created on: 13 May 2020 * Author: Paul */       #ifndef SRC_MYIRQCALLBACKS_H_ #define SRC_MYIRQCALLBACKS_H_   void HAL_GPIO_EXT1_Callback ( uint16_t GPIO_Pin); // SIM Reset detected   void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart);

Hi guys! I need to solve this:Unable to read repository at http://sw-center.st.com/stm32cubeide/updatesite1.Unable to connect to repository http://sw-center.st.com/stm32cubeide/updatesite1/1.0.1/content.xmlConnection refused: connect

Float in printf doesn't seem to work in new projects created in stm32cubeideIf i create a project in sw4stm32 it works, there, it also works if i import the sw4stm32 project, it does not work if i create a new project in cubeideIn all cases the option -u _printf_float is used, but in case of new cubeide project, this setting is somehow ignored and the wrong prinf is included, visible in mapfilegood (imported project):../arm-none-eabi/lib/thumb/v7e-m/fpv4-sp/hard\libc_nano.a(lib_a-nano-vfprintf_float.o)bad(new project):../arm-none-eabi/lib/thumb/v7e-m/fpv4-sp/hard\libc_nano.a(lib_a-printf.o)

I'm preparing a basic embedded programming course. I will use some Nucleo boards with CubeIDE. For the bases of C and C++ programming, I also want to use CubeIDE but I didn't found the documentation for configuring STM32CubeIDE to compile a simple ANSI C project with the Cross GCC toolchain. Can someone help me what's missing to the Eclipse core of STM32CubeIDE to be able build ANSI C project?

STM32CubeIDE 1.3.0I added the "USE_FULL_LL_DRIVER" symbol in my project properties:Subsequently I used "Device Configuration Tool" to re-generate the code (even without having made any configuration changes). At the end of the generation, the previously added symbol disappeared:Obviously if I then try to compile I get an error: I have to add my symbol in the properties again. Really frustrating.Best regardsAndrea

Im getting this error always when trying to program Nucleo board from stmcubeIDE or Truestdio ide.I have tried uninstall and Install IDE. And I have changed may cables also to program.

Hi,​I wrote a simplest program (below) to send sine wave data to PCM5102A (DAC) via I2S.​However, I found only L-ch data is valid and R-ch has no data.Analogue (DAC) output of L-ch is somewhat sine wave, but it is sometimes de-formed. And if I look it closer, I found some noise on the signal. (below captured screen shot)I use HAL and STM32F401. And I2S settings are half-duplex master transmit (only).Kindly enlighten me what is wrong with my program.int main(void) { HAL_Init(); SystemClock_Config();   MX_GPIO_Init(); MX_DMA_Init(); MX_I2S2_Init(); HAL_GPIO_WritePin(LD2_GPIO_Port, LD2_Pin, GPIO_PIN_SET); // LED Off   int16_t Wave_Data[n_data * 2];   for (int i = 0; i < n_data; i++) { Wave_Data[i * 2] = (int16_t) (sin(2. * M_PI * 8. * i / 1000.) * 50) ; // L-ch Wave_Data[i * 2 + 1] = (int16_t) (sin(2. * M_PI * 10. * i / 1000.) * 50) ; // R-ch } while (1) { if (Wave_buf_empty == 1) { while ((&hi2s2)->State != HAL_I2S_STATE_READY) ; if (HAL

I'm trying to create and build and run an example project (6Steps_P-NUCLEO-IHM003.stmcx) for a STMG431 uC on a Nucleo-G432RB eval board. I've taken the following steps:1) Launch ST Motor Control Workbench (Vers 5.4.2) and select the example project.2) Select File-Generation.3) Change Firmware Package Version to STM32 FW V1.2.0 and select HAL drive type.4) Click "GENERATE" button.5) After generate completes, click "RUN STM32CubeMX" button.6) In STM32CubeMX (Vers 5.6.0) click "GENERATE CODE" button.7) Launch STM32CubeIDE (Vers 1.3.0).8) Select File->Import->Import STMe2CubeMX .ioc file and click Next> button.Note: this opens dialog box: "Download selected Files" and another box opens inside that containing "Problem during download and/or Unzip of selected Files. Error downloading the following files: mxusFeaturesAndDescription.json._tmp_ (Not available)"When I click OK the above repeats once. Clicking OK the second time appears to finish and a dialog box opens for the the import

Hi,The link of latest version of STM32CubeIDE is broken. When I try to download the v1.3.0, the download system redirect gnu-tools-for-stm32 instead of cubeide.Regards,Ibrahim

i have got a problem when i download stm32cubeide and install. i have download the file "en.gnu-tools-for-stm32-7-2018-q2-update.20190328-1800.zip" is correct? i have extracted the file, but can not find out the installation file in extract folder. any problem. thank you.kevin

Tried downloading STM32CubeIDE for macOS and Linux (Debian installer). Both of these are not giving the correct download file. It seems to be some kind of source code package to compile a toolchain. Please help!

I created a new source folder in my file stucture, so I have the usual Core and Drivers folders, plus the FreeRTOS folder added by CubeIDE, then I have my App folder. See below.When I compile this, it compiles the three folders the IDE created, but fails on my App folder by not finding included files. When I look at the generated subdir.mk, I can see that there are indeed no "-I" include statements attached to this folder. Why is this not generating properly for this particular folder and how do I fix it? I'd rather not make my own makefile structure as this is generally pretty well defined, but I can't seem to find a setting to make this work.Thanks,Jamie

Hi, I'm trying to use the console in CubeIDE with my STM32F303RE nucleo board and use printf(). For this, I chose an empty project, not STMCube. In the tool settings, I set floating-point unit to none and Floating-point ABI to Software implementation. Then in the syscall.c , I added to following code snippet below.//Debug Exception and Monitor Control Register base address #define DEMCR *((volatile uint32_t*) 0xE000EDFCU )   /* ITM register addresses */ #define ITM_STIMULUS_PORT0 *((volatile uint32_t*) 0xE0000000 ) #define ITM_TRACE_EN *((volatile uint32_t*) 0xE0000E00 )   void ITM_SendChar(uint8_t ch) {   //Enable TRCENA DEMCR |= ( 1 << 24);   //enable stimulus port 0 ITM_TRACE_EN |= ( 1 << 0);   // read FIFO status in bit [0]: while(!(ITM_STIMULUS_PORT0 & 1));   //Write to ITM stimulus port0 ITM_STIMULUS_PORT0 = ch; }   __attribute__((weak)) int _write(int file, char *ptr, int len) { int DataIdx;   for (DataI

I have a strange problem, I have ported the MBED-OS blinkly program to the IDE (this was a relatively painless process) , which sends the device to sleep between flashes. When I download and run the program with the emulator (I have tried blink, stink V2 and V3) it gets a hard memory fault. If I however power cycle the board removing the emulator. It works correctly.I have enabled the debug core of the ST device  HAL_EnableDBGStandbyMode() ;     // Enable Debugger in Standby Mode  HAL_EnableDBGSleepMode() ;       // Enable Debugger in Sleep Mode  HAL_EnableDBGStopMode();       // Enable Debugger in Stop ModeIf I build exactly the same code on GNU Arm Eclipse it functions with the debugger.However I need to be able to debug Mbed projects in STM32cubeide as it is a requirement of my customer that I develop using this platform (it is a great platform )Note that if I disable the sl

勾选了设置中的输入输出浮点，�?然无效。修改为标准库或者精简库也无效。网上也有很多人�?�到了这样的问题。请问怎么解决？官方有解决方案�?�？官方是�?�会在�?�期的版本中解决掉这个问题？

Hi, Im using CUBE IDE with freertos, I'm changing the BASEPRI in my code but it gets reset during the osDelay, why is that ?

I am currently working on a project with STEVAL-STLKT01V1. I have generated code for with weights and USB library using CubeMX for stm32l476jgy and it is working.I am not able to integrate sensor from CubeMX for this MCU as the SPI commnunication pheripherals are not suitable.I am trying to add Sensortile drivers from dalalog application.I know adding my network in FP-AI sensing library is a solution but I dont need other AI algorithms and RTOS properties.I tried importing Sensortile drivers and components into my project and added include files to the folder path. It gives me errors while compiling.I just wanted to know the procedure how to import the Board support drivers into my project without errors.