AutoDevKit Ecosystem

Hi team,I was looking through the steps in the configuration of the sample project: AEK-MCU-C4MINI- AEK_POW_BMSCCTX_GUI_Application for discovery.i made my configurations of the cells as per my project and after allocating the setup, it shows the hardwar connections too.Then it shows to edit the pins in pin map editor which i didn't understand. It says to unassign the allocated pins and copy contents and paste but i didnt understand why we do this and how to do this.( From Step 31 of UM3185 manual). Can someone explain this in detail for me to understand... Thank you.

Dear ST,As you can see from the title we have issues with our SPI connection to the BMS board. We wired everything properly to the BMS connector, checked all the connections, on the MCU-C4mini shorted the JP pins (JP1 and JP2 and JP3 1-2, JP4,JP5,JP12,JP13).We also flashed the pre-built project from AutoDevkit studio (AEK-MCU-C4MINI - AEK_POW_BMSCCTX_GUI_application for discovery) to the MCU.Followed all the steps.We didn't connect any thermistors, and we only have 4, 3.2V LiFePo4 batteries.On the BMS, only the LEDS D2, D8(Blue) and D9 were lit up ~~ we assume the SPI connection is not being established correctly. We hooked up the SPI lines to a osciloscope, please find attached our readings. If needed I can also send a additional osciloscope reading picture.The yellow line is supposed to be the CLK line, we measured from the tiny peak to peak freq of 5MHz, the freq of the whole clock frame was 10kHz.Please advise how to c

Hello AutoDevKit Support Team,I’m setting up an AEK-MCU-C4MINI1 board and I’m unable to get a working debug session through the board’s mini-USB (P2). I’ve read the user manual, followed the bring-up steps, and tried several configurations, but OpenOCD never manages to see the device over JTAG.SummaryExpected: OpenOCD starts, identifies the SPC58 device, and GDB halts at main().Actual: OpenOCD starts but repeatedly reports JTAG scan/IDCODE errors (“all ones”; IR capture 0x3F). GDB then disconnects.HardwareBoard: AEK-MCU-C4MINI1 (power to J2 = 12 V, S1 ON; D10 LED on)Connection: single mini-USB to P2 (no external probe connected to J3)Windows Device Manager shows:Ports

The AutoDevKit ecosystem can now count on a new compact size BMS node and node with transceiver board to match the production form factor when mounted on a real battery pack.Check-out AEK-POW-BMSCC https://lnkd.in/dA8vtr76and AEK-POW-BMSCCTX https://lnkd.in/dxKS_WvV🤩

Hi Team,I am trying to communicate with my bms using raspberry pi.I am using 8 cells in series connected to AEK-POW-BMSCCTX from C0 to C8 (from cell taps-P1 connecter). From the P4 side VIO-3V, Vdd- 5v, GND. I have also connected the MISO,MOSI,CS and CLK of the pi with corresponding pins in bms. Also TXEN-high, DIS-low, BNE-low.Using this run a sample Spi code and there is no correct reply. I just need to know is this connections correct? any extra connections do i have to do?Also after connections, D9,D8 and D2 leds of my bms is light up. When spi is activated D7 led should blink but not in my setup. I hope i get this problem solved.Hardware we’re using now1× AEK-POW-BMSCCTX (one node powered with 8 cells for bring-up).Raspberry Pi with /dev/spidev0.0 enabled.Cell stack: C0..C8 populated (8 cells ≈ 26 V).Two GND_EXT

Hi. I'm looking for a programmer for SPC564L60L5. The best would seem SPC5-UDESTK but it is not available for sale. Or maybe StellarLINK It will be ok for full programming and debugging support for this chip. Or maybe some other suggestions of a programmer who would support SPC564L60L5?  Thank you for your help Best regards Christopher   

Moved  from STM32 forum - this is not an STM32 question.I am facing an issue with the Auto Dev Kit debugger. My previous license had expired (Hightec), and although I tried renewing it and even registered to get a new license, the debugger still does not work.Additionally, I notice that the debugger and flash icons appear greyed out.Could you please assist me in resolving this issue?

I am trying to turn on an LED connected to (PD_9) using the following simple code, but I am encountering an error while flashing the program in UDE. I have attached screenshots of the error and the pin configuration for reference.Code: Simple LED Blinking#include "components.h"/** Application entry point.*/int main(void) {/* Initialization of all imported components (generated automatically). */componentsInit();/* Set PD_9 as output */pal_setpadmode(PORT_D, 9, PAL_MODE_OUTPUT);/* Uncomment the below routine to enable interrupts *///irqIsrEnable();/* Application main loop */for (;;) {pal_setpad(PORT_D, 9); // Turn LED onosalThreadDelayMilliseconds(500); // Delay 500 mspal_clearpad(PORT_D, 9); // Turn LED offosalThreadDelayMilliseconds(500); // Delay 500 ms}}Hardware / Pin Configuration:

Hello, I am trying to use a HighTec Free GCC license with AutoDevKit Studio 2.6.1, but I cannot compile my project. Setup: OS: Windows IDE: AutoDevKit Studio 2.6.1 License: Free GCC Installed compiler: Only VLE compiler (ppc-vle-gcc.exe) is present; ppc-free-gcc.exe is missing Problem: AutoDevKit shows “No license for product (-1)”. Project’s Toolchain Editor only lists the VLE compiler. I am unable to add the Free GCC compiler manually because the executable is not in the installation. Request: Please provide instructions or a link to obtain the PowerPC Free GCC compiler (ppc-free-gcc.exe) compatible with my license. Guidance on installing a

When I use SPC5 Flash Programmer V2.8.1 to connect to the SPC56 CAN programmer, after configuring all the settings and clicking the connect button, the SPC5 Flash Programmer remains in a busy state and fails to establish a normal connection. Could you please tell me how to solve this problem?  Note: The operating system of my computer is Windows 10 64-bit. Besides, when I check the SPC5 Flash Programmer installation Details, it shows that the flash tool plug ins of STMicroelectronics are unsigned, Is this the reason why it cannot work properly? 

Hi,I am using AutoDevKit to develop an application on the SPC563M-DISP. I have a AEK-MCU-SPC5LNK debugger and want to program and debug my software on it. As I know this version only support OpenOCD, but the problem is that I am unable to find the ".cfg" file in the OpenOCD folder, inside the AutoDevKit software.1. Where Can I find the ".cfg" file for the SPC563?2. Can I debug and Program the SPC563 using AEK-MCU-SPC5LNK and OpenOCD?3. Can the AEK-MCU-SPC5LNKU (that uses UDE) program and debug SPC563M-SIP?I currently have the 'SPC5LNK ' and want to use that for developming my app on SPC56, but If that is not possible I can get the SPC5LNKU (UDE version) also, but wants to make sure that I will work.

Hi, I need to change the licensed MAC address for my SPC software.It was previously registered with my Ethernet MAC address, but now I’d like to use my Wi-Fi MAC address instead. Could you please let me know how to update or reissue the license for this change? Thanks in advance!

I am trying to configure BMS63CHAIN component on AEK-MCU-C4MINI1 board connected to an AEK_POW_BMSNOTX but the allocated pin mapping created by the tool does not match the C4MINI1 board connectors.I tried following the AutoDevKit chapter in um3185 Getting started with AutoDevKit battery management system (BMS) evaluation boards:1. Open AutoDevKit Studio 2.6.12. Create New SPC5 Application using SPC58ECxx Platform Component RLA3. Add SPC58ECxx Init Package Component RLA4. Add SPC58ECxx Low Level Drivers Component RLA5. Add AutoDevKit 4 Mini Init Package ComponentNote: Getting Started guide mentions adding AutoDevKit Init Package, but I can not select this together with 4 Mini Init. Seems to be mutually exclusive.6. Add AEK-POW-BMS63CHAIN component7. Open AEK-POW-BMS63CHAIN -> AEK_POW_BMSCHAIN[0]8. Select Node type: AEK_POW_BMSNOTX9. Seletct dspi: dspi0, cs0Go back to the AEK-POW-BMS63CHAIN

Hello ST team,I’m evaluating AEK-POW-BMS63EN with the AEK-POW-BMSHOLD. I’m seeing a bring-up problem where the pack voltage is correct but the board appears “dead” (no refs, no LEDs, SPI values = 0/NaN).SetupBoards: AEK-POW-BMS63EN (2 units available; this post is about the connection/reading behavior).Battery holder: AEK-POW-BMSHOLD.Cells: 18650 “INR 18650 MJ1”.Population: progressed from 6S to 14S (final VBAT ≈ 50 V).MCU/comms: AEK-MCU-C4MLIT1 + AEK-COM-ISOSPI1; UART 115200 to PC.Firmware: AutoDevKit example reading cell/temperature; balancing disabled.Power-up: mate the full holder connector once, with MCU unpowered; then power MCU and start SPI (no pin-by-pin hot-plugging).

Hello ST team,Following on from my “connection/reading” thread, I have a separate issue about physical damage.TimelineWith 4 cells both of my AEK-POW-BMS63EN boards read correctly.When we moved to 6 cells on Board #1, we began seeing the “dead” behavior (refs/LEDs off, SPI zeros/NaNs).We then swapped in Board #2, keeping the same holder and harness. Shortly after connection, Board #2 burned in the same area near the L9963E as Board #1 (photos attached).Later we populated all the way to 14 cells (VBAT ≈ 50 V) to re-check; still no refs/LEDs and SPI zeros/NaNs on the remaining board.Current statusTwo boards visibly damaged in the same L9963E area.We avoided pin-

I have a problem when I try to follow the demo procedure step by step to test if the aek pow board reads the battery pack. I wanted to ask how I can solve this and I would like to know how to understand if the board has correctly gone into debug mode after

Dear ST Experts,I hope this message finds you well.I am currently a research student in Japan working on the ST BMS AutoDevKit ecosystem. I have purchased the full system including:AEK-MCU-C4MLIT1AEK-COM-ISOSPI1AEK-POW-BMS63ENAEK-POW-BMSHOLDThe provided firmware is specifically designed to work with the LG INR18650-MJ1 battery model. However, I have contacted About:Energy regarding this model, and they informed me that they only provide free access to it for Formula Student and racing teams.I would be very grateful for your guidance on the following:Is it possible to use other battery models with the ST BMS AutoDevKit?If so, what steps should I follow to build a compatible battery model? Specifically, I would like to understand:What parameters and conditions are required?How can I implement SoC/SoH estimation for a different battery model using MATLAB and inte

Dear Experts, I cannot access the battery models from About:Energy with ST. I clicked Download model from Autodevkit Studio but the link said 404 page not found with the link: https://www.aboutenergy.io/stmicroelectronics-model-download. I also access the link provided by @Max VIZZINI with the post "Update quick start guide for BMS boards and examples version 2.6.1" slide number 10 but the link and result is the same (page not found). Is there any update about the link? I also attached the error picture for your information. 

how to properly connect multiple L9963E in daisy chain? already tried many mode and tweak. follow the design in datasheet, for transformer isolated and capacitive, but still unable to init. for the first chip, I use SPI. init the first chip is correct, but for the upper L9963E always failed. the mcu I use SPC582B signal seems good, but the ISO transceiver of the chip unable to read.   maybe there any member here thats already succesfully connect the daisy chain ISO

Greetings I have weird situation with AEK-COM-ISOSPI1 and cannot figure out what is wrong. Maybe someone here is experienced with this device and can help me out. I have absolute encoder with SPI. When i connect directly to uC all is working fine. Then i tried to use AEK-COM-ISOSPI1 and have next problem: I can readout the encoder data just with command read, so i generate just clock to start readout from encoder. This works fine, because on encoder side i get correct data 0x9F45. These data are transferred back to uC but here i get messy data from AEK-COM-ISOSPI1. I get data 0x5F61. When i look the SPI signals with logic analyzer i can see that MISO is not sync with CLK cycle. And encoder is always on the same position.  Can anyone help me and tell what im doing wrong here.   My configuration is. Encoder side:NSLAVE=1TxAMP=1TXEN=1ISOfreq=1BNE=1DIS=0SPICLKFREQ=22kohm

Hi,I'm trying to build SPC5 application in VS Studio Code on an agent environment (Windows), which does not have any installed SPC5Studio with Autodevkit plugin. The intention is to start a pipeline on AzureDevOps, where the project can be compiled and build on the agent environment.While executing the command make -j8 all, I'm getting following error: I ran this on VS Code with msys64 installed on windows pc. @Erwan YVIN can you support me on this?  

Dear ST team,Currently, I'm testing SPC560P50L5 MCU with AutoDevKit Studio, and it is going well by importing the sample project. I have noticed that I can enable "User ADC Regular Conversions" in "Application Configuration." Now, I'm trying to control the motor's speed with a potentiometer. So, I enable GPIO-E2, which corresponds to the ADC0_AN[5] pin. Then I generate the code. After that, I can't find how to get that ADC reading in the main.c.Please help me to suggest on it to get the ADC reading from E2 GPIO. Moreover, I declare the variables (uint16_t Bus_Voltage and uint16_t Temp) in the main.c a

We are currently using the AEKS MCU-SPC5 LNKU Kit to debug our custom board. However, we are encountering a "launching error" when attempting to connect to the board via SPC5 Studio. For your reference, we have attached the error image below.We would like to understand whether any specific debug configuration is required within SPC5 Studio for successful debugging.Upon investigating the issue, we came across information suggesting that a PLS UDE software license may be required. If this is the case, we kindly request guidance on how to obtain the license and activate it.Addition

Hi,I am working with an AEK-MCU-C4MLIT1, and trying to debug using the debugger AEK-MCU-SPC5LNKA through the JTAG port. I did a very simple code because all I am interested in now is to ensure that the debugger works properly. The debugging session seems to start properly, as no errors or interruptions occur during the starting phase. The problem is that "Peripherals" and "Memory" are complitely empty while the debug session is running. At the beginning of every debug session the following message shows up: "Break at address "0x404100" with no debug information available, or outside of program code." May it be related to the problem I am encountering?. What I could do? Thanks.

Hello, I want to see basic SOC & SOH values ​​via CAN to PCAN using aek-pow-bmslv. Is there any way to do this?