AutoDevKit Ecosystem

Dear all,Currently, I'm trying to test the SPC560P50L3 MCU for a Motor Control application. I know that I can do it easily by clicking on "import samples from application library". However, every time I try to create the project manually by adding the components like the screenshot below, I always face a lot of errors. I noticed that even though I set up the pins in "SPC56xx Motor Control Component," nothing is updated in the pin MAP view, which is not like in the MCSDK versions. In MCSDK, we set up a lot of things in the GUI, like PWM pins, ADC pins, and so on. After that, we can see it also in the CUBE MX after the

I had a fine working setup with BMS63 for some hours. Than cell 12 showed 0V and the fault light in the ISO SPI came up. A short measurement showed, the cell was indeed empty (I am testing with very old cells). After replacing the cell cell 12 still shows 0V, and the fault light is still on. If I measure with the testpins on the BMS63EN itself, I can see that there is a cell voltage. So something went wrong with the BMS63EN I think.  Do I need to reset the error/fault? In the manual its stated that software diagnostics need to be run in such case. But..how? And shouldn´t that be all reset after a complete disconnect and new init?  

Hi, I am working on a project generated from AutoDevKitStudio-2.2.1, with few SPC58ECxx applications. Able to generate, build and run using the AutoDevKitStudio, and Makefile is auto generated in the project folder.I am using DiscoveryPlus development board with SPC58ECxx MCU. When I try to execute the "make all" command in WSL (ubuntu 20.04.6 LTS), it generate error:After run "make clean" (remove .dep and build folders successfully) , it generate error:

I recently bought the STEVAL-TTM002V1 along with the AEK-MCU-SPC5LNKU debugger since it was mentioned support for SPC56 would be available before 2024. However, I haven't been able to get the AEK-MCU-SPC5LNKU debugger to work with the SPC56.I'm wondering whether the support for SPC56 debugging with the AEK-MCU-SPC5LNKU been officially released?If support is available, could someone guide me how to get started with debugging the SPC56 using the AEK-MCU-SPC5LNKU? Or should I use SPC5-UDESTK only for now?Should I use AEK-MCU-SPC5LNKU or AEK-MCU-SPC5LNK? Any help would be greatly appreciated!

Hello, what does these switchs do? It has something to do with the jtag? (The ones that are right up the botton aside of the jtag)Ty

I installed newer version of AutoDevKit studio from ST website and imported a project fromm samples.I tried to flash the generated elf but it is giving following error. 

Hi Team, We are facing issue in debugging like dissambly view is not showing correct flow even though we clean build the ws. code:  disassembly view:Tried methods:- cha

Yet another step with AutoDevKit. In the latest version 2.6.1, you shall find a dedicated GUI for monitoring of your BMS system, including voltage, current and temperature readings and SoC.

Good morning everyone On the https://www.st.com/en/embedded-software/stsw-autodevkit.html, the en.stsw-autodevkit.zip file is not opened properly. I tried winrar and 7zip file manager, but it results in an error when opening the compressed file. How can you help me? I didn't even find a previous version downloadable to buffer. Thank you.

Dear STMicroelectronics Support Team,We are currently working on a project involving the AEK-POW-BMSWTXA board, which we are interfacing with an STM32F405RGT6 microcontroller via SPI communication.We have connected the board over SPI, but we are not receiving any response from it. To proceed with our development, we kindly request the following:The official User Guide or any detailed documentation for the AEK-POW-BMSWTXA board.A working SPI communication example for interfacing this board with an STM32 MCU (preferably using STM32 HAL).Guidance or sample code to read individual cell voltages from the board.      &nb

Dear STMicroelectronics Support Team,We are currently working on a project involving the AEK-POW-BMSWTXA board, which we are interfacing with an STM32F405RGT6 microcontroller via SPI communication.We have connected the board over SPI, but we are not receiving any response from it. To proceed with our development, we kindly request the following:The official User Guide or any detailed documentation for the AEK-POW-BMSWTXA board.A working SPI communication example for interfacing this board with an STM32 MCU (preferably using STM32 HAL).Guidance or sample code to read individual cell voltages from the board.We are facing difficulty in establishing communication and would appreciate your support in resolving this issue.          Thank you .

Hello! In the SPC58XX-RLA PWM-ICU Test Application for Discovery routine, I would like to ask which CH0 is circled in red as shown in the following figure, CH1... What do they represent? I have been confused whether eMIOS0 CH0 in the first image and Channel 0 in the Channel 0 Setting in the second image are the same channel. I hope you can give me an answer! Thank you!

Hi, after i have downloaded the softare. I tried to monitoring a battery pack made up with 4 cells in series. When i open the GUI, only the first 3 cells are monitored the last one isn't monitored. Anyone have a solution or a schematic about the pin? Cause the gui guide says that the minimum configuration is cell 1,2,13 and 14. Thank you so much

I have some problems while debugging in AutoDevKit.I did find this error log about the problem: Open On-Chip Debugger 0.12.0+dev-00318-g0e98d766e (2023-05-17-15:52)Licensed under GNU GPL v2For bug reports, readhttp://openocd.org/doc/doxygen/bugs.htmladapter srst pulse_width: 100Started by GNU MCU EclipseInfo : Listening on port 6666 for tcl connectionsInfo : Listening on port 4444 for telnet connectionsInfo : clock speed 4000 kHzError: JTAG scan

Hello. STM team. I am using SPC58NH-DISP board and UDE STK 5.2​ with PLS USB/JTAG Adapter for SPC5 MCU.Currently, I am going to buy an additional debugger​, and found AEK-MCU-SPC5LINK(Progrmeer and debugger for SPC5 automotive microcontrollers) below.https://www.st.com/en/evaluation-tools/aek-mcu-spc5lnk.htmlIs AEK-MCU-SPC5LINK is compatible with​ UDE STK 5.2? And, I just need JTAG programming and debugging with UDE STK.If ​AEK-MCU-SPC5LINK is not compatible with UDE STK 5.2, which stm tool is available?My overall workflow​ is coding and building image using SPC5Studio and programming image and debugging using UDE STK 5.2.Thank you.Jaeho

Have you already checked our 2025 newly published brochure?#autodevkit #automotive #embedded

Hello,I have a AEK-POW-NOT-X and a NUCLEO-F401RE that I would like to monitor using the AutoDevKit environnement. I downloaded AutoDevKit Studio 2.6.0 on the ST website, however I can't seem to make it work. I understand that the 2.6.0 version is meant to be a version of SPC5-Studio with the AutoDevKit environnement already integrated; but exept for the icon, name and welcome page, I can't find anything that looks like what I suppose AutoDevKit Studio looks like.When I try to create a new project, there is no "AutoDevKit project" option available. There isn't any "AutoDevKit perspective" either. I downloaded SPC5-Studio 6.0 as a comparison ; it is the exact same, exept for the fact that there are "SPC5 project" and "SPC5 perspective" available...Since AutoDevKit Studio 2.6.0 is different from all the previous versions, even though I've been watching and reading countless re

Hi everyone,I'm working on a university project involving vehicle lateral control using the SPC5-MCTK-01 board. I'm using SPC5 Studio and AutoDevKit, but I'm facing issues with the setup:AutoDevKit installation via SPC5 Studio (Help → Install New Software) fails repeatedly.Launching AutoDevKit directly results in:"Error: Could not create the Java Virtual Machine. A fatal exception has occurred. Program will exit."Tested on both Windows 10 and 11 – same issue.I'd appreciate help with:Correct integration of AutoDevKit into SPC5 StudioFixing the Java VM errorTips or resources for using SPC5-MCTK-01 efficientlyThanks in advance!Best regards

Hello.   I'm using SPC58NH-DISP, and trying to debug using AEK-MCU-SPC5LNKU(debugger) and UDE Starterkit 5.02.04. When I power on SPC58NH-DISP and check if USB driver is installed properly, I can find SPC58NH-DISP works fine and "PLS USB Serial Port" in Windows Device Manager. However, the following error message occurs. <error message> Message from component 'UDEDebugServer' :Unable to establish connection . To correct the situation, check configuration file entries and try again. Message from component 'PpcJtagTargIntf' :Can't connect target ! Message from component 'PpcJtagTargIntf' :No JTAG client found !Please check:- target power supply- JTAG cable connection- target configuration   It seems like the error occurs due to wrong target configuration. I'm curious about where the menu for target configuration is

Dear experts, I am facing an issue when measuring a pack of 14 batteries Fenix ARB-L18-2600. When fully charge 4.23 Volt, the BMS63EN return around 4.0x Volt. When the batteries reduce to 4.12 Volt, the BMS63EN return ~3.98 Volt. Could experts tell me where and how to modify or calibrate the BMS63EN Board?. (I used the Autodevkitstudio-2.4 with both SPC58EC - AEK_POW_BMS63EN_SOC_Estimation_14Cells_GUI application for discovery and SPC58EC - AEK_POW_BMS63EN_SOC_Estimation_Single application for discovery example to measure but they still return same measurement error). I am really appreciating for your help. Best regards, Tri Huynh.

 Hi at the AEKStudio 2.5.0 Release Notesit is mentioned for a while now, that the V2.5.0 is released.But at the ST Site, where the Link is (STSW-AUTODEVKIT - AutoDevKit Studio for 32-bit power architecture MCUs - STMicroelectronics)is still only the 2.4.0 version available.Is there a new release? Or when will it be released?Thx Thomas 

Dear engineer, I found an application about L99H92 in AutoDevKitStudio-2.4.0, is there one about L99MH98 ?Looking forward to reply

Hello everyone, I want to obtain the relevant sample program through AutoDevKitStudio-2.4.0. How can I obtain this License?

Hello, I'm working with the AEK-MCU-C4MLIT1 board, which features the SPC58EC80E5 MCU. While using UDE STK 5.2, I noticed that the JTAG connection is always successful, regardless of the password set to unlock it. This suggests that the JTAG password lock is not yet enabled. What would I have to do to enable the JTAG password lock? Thanks!

Hi We are using STEVAL -TTM001V1 Kit which consists of L9907 driver and trying to interface it with STEVAL-TTM002V1 Controller board (SPC560P50L3)  to run the O-Drive 5312 Motor.   We are using the sample program SPC560P50L3_MotorControl_STEVAL-TTM001V1  from application library to run the motor. We have changed the motor parameters according to O-Drive 5312 motor in the motor settings of the motor control component.