Automotive MCUs

Hello guys,We have designed a board based on SPC58EG40 MCU, this MCU is designed to be programmed via spc5-udestk, all the connections are fine except the Reset line which gives a value of 0.5V, even though it's pulled up to 3.3V by a 4.7Kohm Resistor.Please take a look at the attached PDF for the schematic design.ThanksBasel

A problem occurred during the serial communication test process with the SPC58EC-DISP board.The test environment and problem symptoms are as follows.​test environment1. Apply 12V Power to SPC58EC-DISP board2. Debugging and Serial Communication Test through PLS USB Serial Port (COM6)3. Using SPC5 STUDIO Sample Code ( SPC58ECxx_RLA_SERIAL Test Application for Discovery example code)4. Checked the normal operation of LED of Sample Code (flash sample code using UDE STK )5. Use Docklight to monitor serial communication from PC (Set as Baudrate:38400 Data bits:8 Stop bits:1 Parity:None)6. Set COM6 PORT's Baudrate , data bits, stop bits from device managerproblem phenomenon1. sample code is flashed on the board and then activated, the operation of sending Hello World through serial communication should be confirmed, but a strange value is

Hi,May i know which pin on SPC57S-Eval kit board use for serial clock and serial data?I want to connect the gyroscope sensor to the board.

I add external spi flash to spc572 mcu. Is there any sample code to connect spi flash to spc5 mcu?

Need header connector for AEK-AUD-C1D9031 eval board to be able to modify audio file on board and make changes to .c and .h files to configure to what we want.

pinmap not understood, how can I generate code ? does anyone have links or info/instruction ?

..

HelloI'm working with spc560p and I want to enable serial receiv​e interrupt, that whenever data received, it save the data and so on. I could send data by serial driver as sd_dll_write command and its ok. But when I want to use sd_dll_read, actually mcu stopped. It is cleared that I should use interrupt. But need some help.Thanks​

I want to buy jtag modulewhen looking for it,Looks like I'll have to buy the SPC5-UDESTK-EVAL.(Is that right...? anyway...)So I'm going to buy this product, but there are SPC56 and SPC57 in the description, but there is no SPC58.Is it right to buy this product? Or do I have to buy another product?This is the site you want to buy.https://www.mouser.kr/c/?q=SPC5-UDESTKAdditional question.Does SPC5-UDEDEBG upgrade the license period and write capacity of SPC5-UDESTK-EVAL?

in path and symbols, i include this  

I want to work by adding the c and h files I created.The problem is that the variables and header files declared in ".h" cannot be loaded from the ".c" file.Below is the situation I tested.The c and h files I created are core.c and core.h.not problem As shown in the figure, there was no problem when "components.h" and "stdio.h" were included in the core.c file and variables were declared.However, an error occurred when variables declared in core.h and header files were included.I would like to ask for help on how to solve it.

..

It gives this message - Device specific model "SPC574S64E3" not supported! when I tried to edit the pinmap. Is there way to edit the pin map. what component i should install

Hi, My discovery board is SPC58NH-DISP and I'm a beginner​I want to run the RTOS exampe.​so I tried running the example sequnce.like picture....umm.. I am getting a build error.-----./components/spc5_freertos_tcpip_component_rla/lib/src/FreeRTOS_IP.c:1782:32: warning: comparison of promoted ~unsigned with unsigned [-Wsign-compare]-----How can I solve this?

 I tried to change the chanel number but it didn't work, and i also tried to change the driver under test but it gives me an error. here is my void mainhere is the pin map 

Hello, I am working with a SPC560P and have a problem with float numbers. As soon as I write a calculation with float numbers in my loop, the loop becomes extremely slow (microsecond range for a simple calculation in the loop).What can be the reason for this?Do I have to activate or set anything else and if so where?Please help me Thanks Timo Blessing

I want to know when or how exactly the RX callback function is triggered on the SPC560P - Disp Discovery board. I have created the function at the low level driver at the serial configuration and see it also in serial_lld_cfg. I have defined it afterwards. I want to work in asynchronous mode to avoid blocking. I can also receive single bytes with the function sd_lld_read(). But the callback function is never called or executed. what is the reason? Actually I would like to receive more than just one byte which is why I want to use the callback function as an interrupt. Can anyone help me here? Thanks Timo

..

I am setting up a development environment with SPC5-Studio, Discovery Plus Kit for SPC56 L line (with SPC56EL70L5 MCU) and SPC5-UDESDK JTAG debugger.Initially I was able to set up the SPC5-Studio and upload an example application (LED blinker), but after rebooting my PC the UDE STK tool stopped connecting. No matter what settings I use - the result is the same, the debugger can not connect to the board. I tried reinstalling, UDE and SPC5-Studio to no avail.To debug the problem I have connected a logic probe to the SPC5-UDESTK pins (TCK, TDI, TDO) and I see absolutely no activity on those pins when I attempt to connect with the UDE STK software.It seems that the SPC5-UDESTK device stopped functioning correctly. The Windows OS detects the SPC5-UDESTK device correctly.What can I do to restore the functionality of the SPC5-UDESTK device?

Hello ​I'm using spc560p40 and I tried to read data from other slave. When I monitor the code on logic analyzer, data is OK, but my mcu saw data one shift to right. I used spi_dll_exchange(&SPID, 2 , TX BUFFER, RX BUFFER) to send and receive data. Would you please help me out with this issue.Thanks David​

..

Here is a snip of the error popup.

Using SPC582B chip with only 64 pins, the nexus interface pins will not be available.Does this mean that there are no trace possibilities ?

Hello, i am Tuan from FPT.We are currently using SPC58EC for our project and the issue is HARD RESET occurs after we send request to put uC into Standby mode.It may work sometimes but usually reset uC. So do we have to check for any condition to make sure uC is ready to change mode to standby?Thanks you.

when i configure spc58nn project ,there is pineditor and clock tree ,the configurtion gui. and i cant find any other peripheral configuration gui,any one know this?