Others: STM32 MCUs related

Herkese merhaba, içeriğinde bulunan popüler ESP32 SOM modüllerine benzer şekilde, STM32 serisi için bir Sistem-on-Module (SOM) geliştirmeyi düşünüyorum. Toplu talepte bulunmak istedim: Sanırım bu makul/mantıklı bir proje mi, yoksa piyasa zaten doymuş durumda mı? Biz küçük bir donanım geliştirme şirketi/startup'ız. Şu anda portföyümüzde birkaç ürünümüz var ve ürün yelpazemize yeni, daha yüksek değerli ürünler seçmek istiyoruz. Bu STM32 SOM voltajını ciddi olarak değerlendiriyoruz.

Hello Team,We want to have Standalone Programmer based on ST`s Existing Flash Module Like St-Link V2, V3 Or Mini PCB tools.I should be able to Use External ST MCU to Command this SWD module for Flashing n all task , like CubeProgrammer.Basic Interface like Pushbutton to Start the Flash and Some LED to showcase any Error.   We would not prefer expensive available off-the-Shelf Programmer like Segger..... Not want to use Rpi as well.  This basically for FAE.Regards,

I am currently designing a custom sensor PCB for an underwater ROV project using an STM32 (STM32G431CB). This is my first complete PCB design, so I would like to get feedback before moving on to the PCB layout stage.The board is intended to act as a sensor interface and control unit, and includes:IMU (BNO08X)Depth/pressure sensor (analog)Multiple analog leak detection sensorsESC control via PWM outputsUART communication with a Jetson Orin Nano3.3V regulation using an LDO (LP2985-3.3)The system is designed to operate in an underwater ROV environment, so reliability and noise robustness are important.Before starting PCB layout, I would really appreciate a review of my schematic.Could you please help me with:Identifying any design mistakes or missing componentsChecking power distribution and decoupling strategyVerifying STM32 minimum requirements (BOOT, NRST, SWD, etc.)Any suggestions for improvin

seriously i just want to design my product around an mp2. literally any. i cant pick one because none of them are in stock.im clicking every single mp2 variant that exists. then im picking the sub variant, and then the package. like 3 trees deep. not a single one ive found so far is in stock. these have been out for like years now. how am i supposed to use this chip in my product if it's availability is near non existent?really bad look for st here. 

Hello,A custom control board using an STM32G0C1 stopped working after some time.  Upon plugging into the board and stepping through the program using the CubeProgramer, it was discovered that the PC was cycling through the same addresses repeatedly and getting hung up.  These memory addresses were traced back to various HAL delay functions using addr2line.  Normal operation involves the board initializing and executing various state machines in a superloop (no RTOS), not getting stuck in a "boot loop" delay.  The entire flash memory was dumped to a .bin file and then an attempt was made to erase the flash using the CubeProgrammer with no luck and an error thrown.  No fuse bits or any kind of erasure protection was enabled during the programming of this board.  Then the CubeIDE was used to compile some code and start a debug session.  Somehow, the CubeIDE had no issue loading a program into flash.  This is where i

Hello,I'm developing the software to exchange secure data between a remote host (Linux-OS computer) and a electronic board based on STM32U5 MCU and STSAFE-A110 secure chip. I already implemented the board authentication and I chose to use the symmetric key encryption that the two hosts securely exchange data. For that the two hosts computes each on their own the shared secret after sharing their own public key. That's works fine!But I don't know what functions of stsafe library to use to encrypt and decrypt data using the computed secret key board-side.Could you please help me?Best regards,Alex

Hello, I have been working on a project attempting to get Lua 5.5, Freertos running on a STM32h723.I used cubeMX to generate my project with Freertos enabled.I brought in Lua 5.5 library from their website https://www.lua.org/download.htmlI was able to get it compiling and my project as a whole builds and flashes without errors.Now the part that I'm struggling with. If for any reason Lua has a error the STM32 goes into hard fault and most of the time it seems to be a BusFault caused by IMPRECISERR.I'm trying to figure out if getting Lua to work on the Cortex-m7 is more involved than just adding the library. As I was watching a video from a person that was getting LuaJIT ported to the STM32h7 and he had talked about a few issues he had in regards to the Cortex-m7 

Dear ST Community,We are currently working on the STM32H747 controller using the MIPI DSI interface in video mode.In our setup, we are using the SN65DSI83TPAPRQ1 bridge to convert MIPI DSI signals into LVDS signals for our display panel.The MIPI configuration and bridge configuration details are attached below.After configuring the CSR registers on the bridge side, we are reading Register 0x0A and Register 0xE5 for status verification, as specified in the SN65DSI83TPAPRQ1 datasheet initialization sequence.We have also enabled the test pattern, and the display turns ON (screenshot attached below).Observations:For Register 0x0A, bit 7  is not reading as 1For Register 0xE5, the expected value is 0x00, but it is reading as 0x01We are observing

On the STM MB1363 board I want to expand the USB fucntionality to multi port USB HUB using port CN13 through a HUB like given below. I will be connecting UPSTREAM of the given USB Controller chip to the CN13 STM32 MB1363. TUSB4041I-Q1,  CY7C65642-48AXC Is that feasible? What throughput  can I expect?  

Hi,I´m trying to migrate the example Application p2pServer (BLE) from the Nucleo board to a custom board with an STM32U575CI, but it fails initializing:#### Welcome to ST67W6X BLE P2P Server Application #####<\n># build: 17:52:14 Mar 18 2026<\n>--------------- Host info ---------------<\n>Host FW Version: 1.2.0<\n>[ERROR] [4000] [ST67W6XTask] (w61_at_sys.c:340) sem_if_ready not received<\n>[ERROR] [4000] [ST67W6XTask] (w61_at_common.c:375) sem_if_ready not received<\n>[ERROR] [4000] [ST67W6XTask] (w61_at_sys.c:312) Could not init Modem handler<\n>[ERROR] [4000] [ST67W6XTask] (main_app.c:975) [ERROR] in W6X_Init API<\n>[ERROR] [4000] [ST67W6XTask] (w6x_sys.c:115) W61 Init failed<\n>[ERROR] [4000] [ST67W6XTask] (main_app.c:401) Failed to initialize ST67W6X DriverAny idea what could be the problem?BestAchim

I am not able to view stm32N6 PSRAM @ 0x90000000 with IAR Memory view, it only shows --. And after I tried to access 0x90000000, the debugger seemed to hang up.I tried with STM32N6570-DK XPI_PSRAM_MemoryMapped project. I set a breakpoint at line 197 -- if (errorBuffer == 0) after it read/wrote PSRAM successfully. When it stopped at the breakpoint, I opened the memory view to check memory @0x90000000. It failed.If I did the similar with stm32CubeIDE, it worked fine.  Any idea why the IAR was not working?

I’m using a NUCLEO-H533RE and CLion as my development environment. Configuring and building my STM32 project works fine, but I haven’t been able to get debugging to work. I receive the following error:Error in initializing ST-LINK device.Reason: Unknown. Please check power and cabling to target.Using STM3CubeProgrammer I can connect with the board and did the full chip erase.The attached images show the current settings.Does anyone have any idea?

Hi, im doing a line follower and using the mcu stm32 f411, its a small development board arduino nano style, and i conected it to the motor driver tb6612fng, and it seems to have backfeed motor suply voltage on the logic pins and it burned my mcu.My question is how to prevent this?

Hello,I recently came across an ST article describing a Condition-Based Monitoring architecture using a dual-MCU approach, with an STM32L476RG handling signal processing (and potentially edge AI), and an STM32WL dedicated to network connectivity.I find this architecture very interesting and relevant for a project I’m currently exploring, but I would like to better understand what level of support and resources are available from ST for implementing such a solution in practice.In particular, I have a few questions:Does ST provide official support or reference designs for this kind of dual-MCU architecture (STM32L4 + STM32WL)?Are there any example projects, application notes, or firmware packages that demonstrate communication between the two MCUs in this context?Regarding FUOTA (Firmware Update Over The Air), are there existing solu

Hi,I have STM32H755ZIT3 controller, and I am tying to read voltage sensor AMC1333M10 and sensor has internal clock of 10 MHz . I am trying to read on controller DFSDM channel 7, core M4 with clock 64 MHz . Is this practically possible to read in such a configuration ? As when I read the value(dfsdm_buffer), it is always 7 (~0) whether there are voltages on the terminal or not.Code: // start HAL_DFSDM_FilterRegularStart_DMA(&hdfsdm1_filter0, (int32_t *)dfsdm_buffer, BUFFER_SIZE); // callback : void HAL_DFSDM_FilterRegConvCpltCallback(DFSDM_Filter_HandleTypeDef *hdfsdm_filter) { ... }Following is my configuration for DFSDM in MX : Channel 7 : "PDM/SPI input form ch7 and external clock"Channel 7 :Channel 7 Parameters:Type : "SPI with rising edge"Offset : 0R

Hi, please share CMRT (Conflict Minerals Reporting Template) EXCEL FILE FOR STM32F051K8T7

Problem:    nRST appears to leave the STM32U5 inoperative when applied at any time other than followingapplication of power. Serial traffic is expected through UART4 following a reset. When the boardis powered on, the STM32U5 software runs as expected; initial traffic through UART4 and thenthe STM32U5 interacts through UART4, accepting typed in commands and producing expectedresponse traffic.If the reset switch (SW1) is used to reset the STM32U5, it does not produce the expected serialtraffic and no longer communicates through UART4.A power-cycle of the board produces expected serial traffic and the board interacts (throughUART4) as expected.The board does not reset correctly after being programmed (using a STLINK-V3SET program-mer). The program flash is, however, correctly programmed. The updated flash image works fol-lowing a power-cycle.This schematic fragment shows power,

Hello to the STM32 Community, I am trying to connect a fast TI DAC904 to a Nucleo board with H743. I am using it as a single M7 core. I have built a project with CubeMX where:Timer1 -> DMA -> FMC -> DAC904Short sine buffer in RAM-D1 and DMA as circular bufferIt works but I am getting maximum speed of 12.6 MSps.I have tried to modify the timer frequency but I am getting a limit at that speed Is there a way to make if faster?Thank you Benny  

HiHere is my scenario:I want to use USB Type C Connector for Power Delivery(upto 65W) and also, for communicating with STM32F767ZIT6 on my Hardware.Power Delivery is used to charge a 14.4V Li Ion Battery using Battery charger on my hardware. So, And USB Communication takes place with STM32F767ZIT6 Full Speed. Charging and Communication don't need to happen at the same time.So, USB-C Connector will either be used to charge the battery using a AC-DC wall adapter or communicate with STM32 on my hardware using a USB-C Cable from PC. Only one of these things will happen at a time. I was thinking of using STUSB4500 for Power Delivery such that it negotiates 20V, 3.25A with Wall Adapter but it looks like VBUS Sensing PA9 would be a problem when PC is connected(VBUS= 5V) or wall adapter is connected(VBUS= 20V).So, wondering if there are better/easier options to do this? Changing the STM32F767ZIT6 to something like&n

Hi everyone,I’m currently working on a project using an STM32 Nucleo L476RG and a Velleman VMA302 Bluetooth module (HC-05 type), and I’m trying to send data over Bluetooth to my Mac.I configured USART1 at 9600 baud in STM32CubeIDE, and my code is continuously sending a simple message like "Hello". The module is powered and appears to be working (LED is blinking, pairing works with my Mac).On macOS, I can see the Bluetooth device and pair with it successfully. I also see the serial port (e.g. /dev/tty.HC-05-xxxx), but when I try to read data using the terminal command:screen /dev/tty.HC-05-xxxx 9600I don’t receive anything.I’ve already checked:TX/RX connections (crossed correctly)

Hi I have a USB-C Connector that will be used for Power Delivery Sink  for charging and USB Full Speed Mode(12Mbps) for communicating with onboard STM32F767ZIT6. But only one thing will happen at a time.    As seen in the attached schematics, I have used STUSB4500 as PD Sink controller. I will communicate with it via I2C using STM32. I understand that this STUSB4500 will negotiate 20V(60W which i want for charging) with the source(which in this case is AC-DC Wall adapter) in Power Delivery Mode. But my question is during USB Full Speed Mode Communication with STM32, when that USB-C Receptable is connected to a PC instead of Wall Adapter. As during charging mode, USB_VBus is 20V and in Full Speed mode, it is 5V and my STM32 is Self-Powered and VBus sensing is mandatory. But due to USB VBus varying between 5V and 20V, I cant connect it to for exam

Hi, We are using an STM32F103 as a controller for a Half-bridge dc-dc convertor running at 110Khz. We are facing an issue where the microcontroller is resetting every minute when output crosses 12A. We disconnected all peripherals, removed all protections and kept only the PWM and reset problem sustains itself. On further inspection, we found that the PWM duration increases for a few cycles and then the microcontroller resets. It seems to us that the microcontroller clock slows down and then finally stops forcing a reset. We do not have watchdog timer implemented.We are using a 8MHz crystal. Please check attached image (CH1 - reset line, CH2 - Independent PWM, CH3 - Half bridge high side) The fun fact is that if we place the microcontroller on an external PCB and connect to the gate driver with wires, we do not see the microcontroller resetting. (even without the crystal). Sometimes, attaching an oscilloscope

Hello,We are currently working on STM32C542CCT6 from the STM32C5 series and developing custom Flash and Data Flash drivers.Issue 1 – Hard Fault when accessing FLASH_SIZEWhile executing code generated by STM32Cube, the following check causes the system to enter the Hard Fault handler:if (FLASH_ADDR < (FLASH_BASE + FLASH_SIZE)) /* Main User Flash */The FLASH_SIZE macro reads the value from the device information area. However, when the code attempts to access FLASH_SIZE, the system immediately enters the Hard Fault handler.If we manually hardcode the flash size value, the code works correctly.Our questions are:Is there any specific register configuration or initialization required before accessing FLASH_SIZE on this device?Is this region restricted due to Trust Zone or privileged access on STM32C5 devices?Issue 2 – NMI when reading Data FlashWe have enabled Data Flash by setting: EDA

Hi,in AN5225 an anylzer is used (e.g. Fig 22, page 33). Can anyone tell me which analyzer it is?Best regards,Achim

Split from How to program and debug the STM32 using the Arduino IDE.Hi,I am new to this forum having just bought a Nucleo STM32G431 which I want to program using Arduino 2.3.4 on MAC OS 11.7.11. On trying to upload the simple blink example I get the error:Warning: long options not supported due to getopt from FreeBSD usage.getopt: illegal option -- aTerminating...Failed uploading: uploading error: exit status 1Having read around this a little it seems that MACOS is using a BSD version of getopt which doesn't support long options. I believe the problem is in the Arduino core for STM32 MCU based boards (I have version 2.12.0 installed).  Do you know of a workaround for this? Do I need to install the GNU version of getopt and is this