Others: STM32 MCUs related

Greetings,I have an ST32L151CCT6 part with pin PB5 connected to the DE pin on an THVD1400DR RS485 Transciever, my whole system is designed to be low power, and the MCU enters stop mode to achieve that from its side, every pin goes to analog mode. I have meassured the power consumption of my whole system when I take out the transciever and it reaches the expected 40uA.The problem:Current rises up to 11mA when I solder the transciever back, even so, I mannaged to find the exact connection with the problem, when I raise the DE Pin on the part breaking the direct connection to PB5 the higher current consumption problem dissapears.What kind of worked:Setting the PB5 pin to INPUT makes the current consumption go up to 150uA, wich is way higher than we aimed for.What I have tried so far:I tried placing a 470K resistor in series to the trasnciever and the vol

Split from: Evaluation of Encoder Signal Level Shifting Approach as that was a different issue, and has been solved.I am also working with this same issue, in my case i have a encoder operating at 24V, and signal in comparable frequency i have implemented a simple voltage divider, the circuit works just fine, but as i don't have equipment to measure the noise and also i would prefer to have galvanic separation to my MCU, so in this case is there any good suggested  level shifter or optocoupler, should i combine the both strategy of voltage divider and optocoupler or just 1 is fine (from perspective of noise and safety)?

STM32F072RBT6 ADC Channels IN0–IN13 Always Read 4095, IN14–IN15 Work NormallyI have 5 boards based on STM32F072 Peripherals connected SPI1(ATM90e36 Running at 3.3V and 3.3V spi pullups using 10k), i2c1(ADS1115 running at 5v and 5V pullups using 10k), Uart1,Uart2,Uart3 (all in async mode) , 9 internal ADC channels and other pins as GPIO attaching the snapshot of my config.ISSUE : PC0,PC1,PC2,PC3,PA0,PA1,PA4 pins always reads 4095 and PC4 and PC5 reads 170-180 counts PC0-PA4 channels is connected to pressure sensor in this way Signal ── 4.7kΩ ── PC0 (ADC input) ── 10kΩ ── GND signal expected is 0-4.5VPC4, PC5 are Pulled down using 4.7k (Series resistor for NTC).directly reading VREFINT channel gives 4095 but it should be around 2000 Hardware sanity checks:GPIO toggle toggles the respective pinGPIO Read give

Heyho,I have an application with an STM32H7x3, which might be talking to some other STM32 (type TBD, probably something <= G4) on another stacked PCB.This is only a control interface, so no data streaming with a minimum data rate.I am looking for the "best" interface, with that I mean "highest speed at lowest complexity".  Hardware limits:trace length max 30 cm, probably over 1 or 2 connectors max. 4 pins (+1 chip select for each participant also okay)max. 4 STM32x + STM32H7x3 on the "lines"So, I2C or SPI - or anything else ?For reliability I like the I2C's acknowledge, SPI is surely faster and has no address "overhead".Thanks in advance for your input!  

stm32使用串口空闲中断，仿真过程中打断或者程序停止运行时串口要是外部有数据geistm32发送，运行后不在进串口空闲中断这种情况谁遇到过， Translation with google: When using a serial port idle interrupt in STM32, if the simulation is interrupted or the program stops running, and there is external data being sent via the serial port, the STM32 stops sending data after the program resumes running. Has anyone encountered this situation?

Hello,I am using an STM32H753IIT6 AA184 VQ V TWN AA. It does not communicate when I connect my serial board through serial communication and try to upload a TTL file using TeraTerm. The device is not even detected. However, when I replace the chip, it starts communicating normally. This has happened with multiple units and the result is the same.We verified that there are no soldering issues—X‑ray scans showed no defects. We have also tested all voltage levels and clock signals according to the datasheet, and everything appears correct.I am concerned about what might be causing this issue. Could you please help me understand what could be going wrong?Thank you.

Hi,Have this working on STM32F302R8 but cannot seem to get my SD Card working on an STM32F446RE. Using hal 0.23.0 with stm32F446 and embedded-sdmm 0.9.0); let sd_mosi = gpiob.pb15.into_alternate::<5>(); let sd_miso = gpiob.pb14.into_alternate::<5>(); let sd_sck = gpiob.pb13.into_alternate::<5>(); let mut sd_spi = Spi::new( dp.SPI2, (Some(sd_sck), Some(sd_miso), Some(sd_mosi)), Mode { polarity: Polarity::IdleLow, phase: Phase::CaptureOnFirstTransition, }, 400.kHz(), &mut rcc, ); let sd_spi_dev = ExclusiveDevice::new_no_delay(sd_spi, sd_cs).unwrap(); rprintln!("Reading file..."); let num_bytes = sdcard.num_bytes().unwrap(); rprintln!("SD Card Size: {} bytes", num_bytes);Which gives[2026-03-01T05:30:04.085Z, +020837ms] panicked at both_test/src/main.rs:184:40: [2026-

One small issue I have. I have a custom STM32F411CEU6 board, quite similar to the WeAct Black Pill in terms of connections, except for the fact that I have a LED on pin PB13, and whenever I try to blink it using:while (1) { /* USER CODE END WHILE */ HAL_GPIO_TogglePin(GPIOB, GPIO_PIN_13); HAL_Delay(500); /* USER CODE BEGIN 3 */ } in the STM32CubeIDE, everything works fine and dandyThe moment i switch to using the Arduino Framework, albeit with the Arduino IDE or PlatformIO, with parameters of:platform = ststm32 board = genericSTM32F411CEusing the code:#define LED PB13 void setup() { pinMode(LED, OUTPUT); } void loop() { digitalWrite(LED, HIGH); delay(1000); digitalWrite(LED, LOW); delay(1000); }or anything similar, it just doesn't work! It always says the uplo

Hi, I am working with a custom board using the STM32H757BIT and a Riverdi RVT70HSMNWC00 connected through MIPI DSI.I followed the “lv_port_riverdi_70-stm32h7” example for the CubeMX setup and for the DSI display initialization.The system runs from a 25 MHz external HSE, and I have tested the DSI clock using both the HSE and PLL2Q.HAL version: V1.12.1.The UI framework is LVGL. My issue is that the display stays completely black. When LVGL triggers the flush callback, nothing appears on the screen. The backlight PWM is working correctly: it runs at 48 kHz and currently uses a duty cycle above 90%, so the panel should be fully illuminated. The screen content I want to show is extremely simple, just for testing: /*Change the active screen's background color*/ lv_obj_set_style_bg_color(lv_screen_active(), lv_color_hex(0x003a57), LV_PART_MAIN); /*Create a white l

Hello STM Community,I am trying to achieve live camera streaming using STM32H723VGT6, but I am unable to get the result for USB_UVC, Ethernet, using esp32 wifi, if there is any help available, please share it. Also, do share any GitHub link if available.  I am using the Weact mini STM32H723VGT6 board, and I have connected a camera module OV2640 to it.I have referred to the GitHub link below, which is for the H743 controller, but it hasn't shown any expected results. https://github.com/WeActStudio/MiniSTM32H7xx   Any guidance from ST engineers or Community members would be very helpful.Thank you in advance.

Hello ST Community,I am working on a commercial vending machine controller and would like to get feedback from ST engineers and experienced STM32 designers regarding a system architecture change.Problem StatementOur current system uses a single MCU, but we are now hitting hard peripheral limits, mainly:Timer availability (stepper + DC motor control)GPIO interrupt countGPIO pin availabilityIncreasing real-time jitter when multiple loads are activeThis is not a software optimization issue anymore; it is a resource saturation issue.Because of this, we are planning to move from a single-MCU architecture to a multi-MCU system.Proposed ArchitectureMaster MC

Hi I'm new to the STM32 board but not to Arduino IDE. I want to use two STM32 boards (with DXV lr30 900) for LoRa communication. I'm starting with a minimal program (without LoRa), just to see how the communication works between the STM32 and the Arduino IDE's serial interface. I can compile and download this program without any problems, but I don't see anything on the serial interface, whether using the ttyUSB0, ttyUSB1, or ttyS0 ports at 9600 baud.   here is the test program   void setup() { Serial.begin(9600); delay(2000)

I want to make a speedometer with a STM32 MCU. What is the best solution. Do stm32 have any products wich works as a plug and play speedometer.

Hello Engineers,I have recently started developing a product based on the STM32F446RET6 MCU integrated with the RFM95W (SX1276) LoRa module. My goal is to transmit sensor data to a LoRaWAN network server such as TTN or ChirpStack.I am using STM32CubeIDE for firmware development. However, I have not been able to find clear documentation or structured examples explaining how to implement LoRaWAN (end-device) communication using this MCU and radio combination.What I am Looking For:A stable and recommended LoRaWAN library compatible with STM32CubeIDEGuidance on integrating the SX1276 (RFM95W) with STM32 HAL driversA basic bare-minimum example that sends dummy payload data to a LoRaWAN server (preferably OTAA)Any reference projects, repositories,

Hi,I’m experiencing issues configuring a display using a custom PCB with the STM32H747BIT MCU and LVGL for the UI. Currently, the project runs a minimal setup with only one loop calling lv_timer_handler();. At this point, my main goal is to get the screen working correctly.I’m using LVGL in direct mode for the display buffers.The issue I’m facing is that the screen occasionally shows horizontal glitches. I’ve created a simple spinner using the following code: /* Create a spinner */ lv_obj_t * spinner = lv_spinner_create(lv_screen_active()); lv_obj_set_size(spinner, 64, 64); lv_obj_align(spinner, LV_ALIGN_BOTTOM_MID, 0, 0);You can see the glitch in the attached video.As you can see, the glitching is more noticeable in Video_1 than in Video_2. These

/* * ledfunc.c * * Created on: Jan 16, 2026 * Author: roman */ #include "main.h" #include <string.h> #include <stdio.h> #include "ledfunc.h" uint8_t flag = 0; uint8_t blue_but_click_number = 0; char pressedKey='\0'; char readChar='\0'; //UART_HandleTypeDef huart2; void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin) { flag = !flag; char main_str[50] = "Button clicked: "; char num_str[45]; // Buffer to hold the string representation of the integer // Convert the integer to a string snprintf(num_str, sizeof(num_str), "%d times\r\n", ++blue_but_click_number); // Concatenate the new string to the main string // You must ensure main_str has enough allocated space for both parts strncat(main_str, num_str, sizeof(main_str) - strlen(main_str) - 1); HAL_UART_Transmit(&huart2, (uint8_t*)main_str, strlen(main_str), HAL_MAX_DELAY); char msg[20]; sprintf(msg, "PRESSED: %c\r\n", pressedKey); // Formats string + char HAL

I was just wondering if there was a suitable communications shield that I could use for my NUCLEO H753ZI development board, preferrable if I also use the X-NUCLEO-GFX02 LCD Shield on top.I've looked almost everywhere but there was no single solution for what I wanted:* RS232 with full handshake support (3T5R)* RS485 support for both half- and full duplex* RS422 since this looks very much like RS485 full-duplexOther nice-to-have features would be fully configurable either by jumper setting or MCU control, various testpoints that are easily accessible, and could handle both 5V and 3,3V input voltage.Since I couldn't find anything that even came up close to what I was looking for, I thought of designing one myself! :)What I came up with was a shield that has been build around the TI THVD4431 chip that has support for all three protocols and is easily configurable by selecting corresponding pins to set high or low.After s

..

Hello there! I'm new here. I’ve just started working on my master thesis, which involves the STM32N6 and an image sensor.From what I've heard from colleagues, working with a camera that lacks a proper datasheet or driver can be frustrating. To avoid falling into the same trap, I’ve been searching for cameras/modules compatible with the STM32N6 that I can get up and running.Here's what I'm looking for:I need to capture images (video is not a priority) in daylight (IR filtered).Once sunlight fades, I will activate my IR illumination and take IR-only images. RGB should ideally be blocked to avoid mixed images. My two approaches so far:1. RGB Camera with Motorized Filter (e.g. RaspberryPi IR-Cut, motorized): It uses a clear filter and an IR-cut filter. The clear glass could potentially be replaced with an RGB-blocking filter.2. Dedicated

Split from STM32H503 incorrectly marked as having CORDIC/FMAC - this is a different topic.Thank you, I will try this.But in the meantime, the Windows standalone MCU Finder app has just become broken.Selecting any entry of the PRODUCT INFO -> Segment options, return no results. i.e. if I reset, then choose STM32H5 series, or STM32U5 series, no results are shown. This definitely used to work. The Android app still works, but still shows the incorrect H503 entries.

I am using a STM32H747I DISCO board as the target to evaluate the Audio Weaver Designer from DSP Concepts. In order to connect with Audio Weaver, the STM32747I DISCO board needs to be programmed with the Audio Weaver BSP for this board.I need to program my board to connect up with Audio Weaver. I need to get either the binary or the BSP source (or ideally both). I cannot find this anywhere online and could not find it on DSP Concepts website anywhere. From what I can tell each target partner maintains the BSP, so does ST have this?

 Hello ST Community,I am using TSD HD Gen4-STM32-43CT-01 display module which has STM32H7S7I8T6 MCU.I am facing an issue where I am unable to connect or disconnect the debugger using MB1440C, while the same debugger works perfectly with other TSD HD Gen4 displays.Debugger setupDebugger: MB1440CInterface: SWDConnections:SWDIO → JTMSSWCLK → JCLKGND → GNDThis setup was working earlier on the same board.What changedThe last firmware flashed was a boot-level application intended to write custom data into external QSPI flash:External Flash:

HelloI want to create sort of application that transmit and receive messages between 2 STM32F407 DISC0 and echo the transmited and received messages in PC screen(sort of chatbox)any hints how can I do it?and is it easier using USART or SPI?

Does anyone know what settings are needed to check the internal flash memory using the STL library? I wrote a small test firmware (for a 61508 safety application without TZ) using the STL library, which is supposed to perform a self-test flash memory check.However, this test always fails.  I ran the checksum check using STM32CubeProgrammer v2.20.0. I had to manually enter the settings for FlashStart, FlashEnd, and FlashSectionSize (0x08000000 0x0800E000 0x00010000) because the macros from the readme file didn't work.  The STM32CubeProgrammer the

 Hello everyone,I am working with STM32G431CBT6 using Keil MDK. I want to develop a bare-metal project (without CubeMX or HAL).However, when I open Manage Run-Time Environment (RTE) in Keil, under the Device section I only see the CubeMX option. The “Startup” component is not available.What I expect:Under:Device → StartupI expect to see the standard startup files for STM32G4 series so I can build a bare-metal project using only:CMSIS → CORE Device → StartupWhat is happening:Only CubeMX appears under the Device section.The Star