Product forums

Hello ST Community,I M USING STM32H745I-DISCO (MB1381-H745XI-B02), WHICH COME DEFAULT MII MODE, TO CONFIGURE IT ON RMII, WHAT CHANGES I HAVE TO DO IN HARDWARE, IOC. AS THIS BOARD HAVE ETHERNET IC LAN8742A-CZ-TR WHICH HAVE BOTH MII,RMII PROTOCOLS.AS I HAVE SEEN SOME VIDEOS ON ETHERNET FOR DIFFERENT STM32 CONTROLLER IN RMII, I M NOT ABLE TO GET RESULT.  I WANTED TO KNOW DO THIS BOARD CONFIGURE IN RMII, IF YES THEN TELL ME HOW I CAN DO. HERE IS CONFIGURATION I HAVE DONE IN MY PROJECT.  PG11 ETH_TX_EN ARM Cortex-M7 n/a Alternate Function Push Pull No pull-up and no pull-down Very High n/a   true PG14 ETH_TXD1 ARM Cortex-M7 n/a Alternate Function Push Pull No pull-up and no pull-down Very High n/a   true PG13 ETH_TXD0 ARM Cortex-M7 n/a Alternate Function Push Pull No pull-up and no pull-down Very High n/a   true PC5 ETH_RXD1 ARM Cortex-M7 n/a Alternate Function Push Pull No pull-up and no pull-down Very High n/a   true PC4 ETH_RXD0 ARM Cortex-M7 n/a

It looks like I have the 32F469IDISCOVERY board that looks to be powered ok via USB connector CN13, however the board doesn't appear to have demo software preloaded. COM LED LD6 flashes red. I note on the ST website that there is the 32F469IDISCOVERY compiled demo binary, which I have downloaded. The Readme says: The QSPI external flash loader is not integrated with supported toolchains, it ís only supported withSTM32 ST-Link Utility V3.7 or later. But the ST website says that the ST-Link Utility is NRND and to use STM32CubeProg instead. I've tried the latest version of STM32CubeProg and it can't connect to the board via USB: Error: Establishing connection with device failed. What is the best way of programming the board with this file please? Kind regards, Al

CubeMX 6.17. When creating a new project for H533RETx or for the corresponding Nucleo-H533, SYSCLK is set at 32 MHz.Not sure whether or not it is intended, but it looks like a trap for a new user, since the MCU datasheet talks about 250 MHz.Instead, example projects for Nucleo-H533 (at least the couple that I've seen) quite reasonably run the MCU at 250 MHz, driven from the crystal present on the board.

Dear,When running the FSBL that includes HAL XSPI initialization logic on the Nucleo-N657X0-Q board (MB1940-N657X0Q-C02), the flash erase with the STM32CubeProgrammmer v2.22 sometimes fails. However, if I leave out the XSPI initialization logic for accessing the NOR flash, flash erase always succeeds. BOOT pin 1 is set to DEV and I am loading the FSBL firmware directly into RAM.Do you have any idea why XSPI Init causes the flash erase to fail ?BR,EdwinD 

I have created a project with a scroll wheel of 10 items, each item is displaying a single digit 0-9. Imagine an odometer for instance.  I am incrementing a variable(num) every second and usingscrollWheel.animateToItem(num, 20);to scroll through the list of items, it is working as expected until it gets to 9. Instead of it the scroll wheel continuing to rotate the same direction to 0 it reverses the direction of rotation and scroll past all other digits to get back to zero.  I have verified I have the scroll wheel set as "Circular" and it does indeed display the scroll wheel correctly as if it was circular.  Can I somehow change this behavior?

Hello, we have a working design that is in production, but obviously cannot keep building because of the EOL variable capacitors. Our application is reader only, no card emulation. Since we don't need CE, do the variable capacitors need to be populated? Or can they be replaced with a fixed value capacitor? If the latter is correct, then what value capacitor to use? We want to minimize changes to the design since it is working well. In the future we will change to the ST25R300 bur right now we have to stick with the current design. Thanks,Derek

1. Where can I find pin function list for SPC582B60E1CD00X MCU. Package: eTQFP64  2. Suggestion on tool used to configure pins according to application and generate code.

  I am testing the board with a 14s Li-ion battery, but I am unable to read the cell voltages or configure any register through the GUI. I shorted the X1 and P2 power supply inputs and supplied 12 V to both. This was the only setup in which I could get a green ACK indicator. The results were: Only cell 1 showed a voltage, but it was incorrect (5.8 V). When I try to write or read any register, I receive an ACK, but the register value does not remain as written. I also tried to connect VBAT (P2-15) to C14 (by soldering R22) and GND (P2-9 or 23) to C0, but in this configuration the device does not start and the D13 LED does not blink. I tried several times, resetting all the power supplies in different sequences, but I still could not communicate with the device. After returning to the initial setup, powering the L9963 with 12 V, I was again unable to configure the ID or take any measurements.    

can someone help me with communication of l9961 chip to get voltages of 4s cells n current n charge accumulated by using esp32 or aurdino i dont have this chip n i am not a coder i tried my best but can get any data from the chip just i2c add 0x49 n this register 0x00 gives  0x41 n nothing please hep

Hello, we are in the process of developing a BMS using an STM32 and L9961. We were wondering if there was any source or example code of a full BMS we could have access to in order to speed up our development. I am aware of the example code on the product page but was hoping there would be something more fleshed out. In addition, I wanted to know if ST has a vault of cell models that we can use with the BMS for fuel gauging? We use Molicel P50B cells and plan to use Molicel P60B cells in the future. Thanks,Jon

Hi all.I'm new to STM, but have been designing and making embedded MCU products for over ten years.I was drawn to the STM32F105 series because of the USB DFU, to allow for field updates for prospective customers to update a product we're developing. Outside of USB DFU functionality, we just need 3x UART's, one GPI, one GPO. That's it. We steer clear of USART1 because of it's overlap with OTG_FS pins. We have got our product working using a ST-Link programmer, but not as yet using the USB DFU.Our USB connection just isn't enumerating. The wiring is correct when compared to off-the-shelf STM32 enabled boards with OTG USB interfaces.I am across the date code bootloader issue as described in AN2606, our chips definitely come with bootloader 2.2. I have VBUS from the USB-C tied to PA9 (OTG_FS_VBUS). Yes, USB-C but with the 5.1K resistors between CC1, CC2 and GND. NRST is pulled to 3V3 with a 10K pull-up. Boot0 and Boot1 is pulled to GND via a 10K pull-down, Boot0 also runs to a tactile NO p

Hi, I've just installed v2.14.0 for the first time, but it will not start up. All I get is the blue STM screen for a few second, then it disappears. I tried the command prompt start up detailed in This Post but I end up with an error message, shown below. I need help on how to proceed as I do not have JRE installed on my PC, but have had it in the past. I've tried re-installing STM32... but that didn't help Exception in Application start methodjava.lang.reflect.InvocationTargetExceptionat sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:62)at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43)at java.lang.reflect.Method.invoke(Method.java:498)at com.sun.javafx.application.LauncherImpl.launchApplicationWithArgs(LauncherImpl.java:382)at com.sun.javafx.application.LauncherImpl.launchApplication(LauncherImpl.java:321)at sun.reflect.NativeMethodAccessorImpl.invo

Hi, I'm working on the STM32H7S7L86H with cube MX 6.17 and cube H7RS 1.3.0I need to use RNG in appli and boot context but it is grayed because it accept only one context. It also block the usage of the hash module.Any idea how to fix this ?Thanks 

Good day, ST community,I am writing to inquire about the possibility of updating the custom container used on each screen when a new change is made to the custom container template. Currently, I am required to delete the old custom container widget on all my screens and add the new updated container manually each time. Thank you in advance for your assistance.

Hi,I recently just finished the Yocto Bringup of a custom STM32MP15FAA1. Everything seems to be working in my application. I am now looking to begin development of the M4 in which I need access to either SWD or JTAG to do lower-level development. Unfortunately, I am having trouble connecting to either interfaces through both CubeIDE and also manually inputting OpenOCD in an IDF Powershell instance.I presume the easiest way to get to my goal is to setup SWD which on the MP15 maps to TMS (SWDIO) and TCLK (SWCLK) and I connected GND and VCC. My STLinkV3-MIME detects 3.3V on the reference line but can never connect to target. This is my first time working with a SOM as most of my development is on base Cortex M microcontrollers so I have a few questions.1. Is there anything in the M4 device tree that can be preventing JTAG from operating like the STPMIC? I do have M4 RPROC enabled in my device tree and the file descriptor is available for me to access.2. Does the boot mode matter? My end a

Hello,I am using STM32H750 and X-Cube-Crypto lib. I am working on a secure boot and want to calculate the app Hash value to check integrity. The library works fine for STM32L5 Mcu (Already tested) but not with STM32H750. I verified that I am using the correct lib libSTM32Cryptographic_CM7.a.The issue I get is a Hardfault triggered by a function in the lib. When I investigated more, I found that The Mcu tries to load data from a Peripheral Register not mapped for STM32H750 MCU.What do yo think could be the issue? Thanks,Ayoub 

AmbienteSistema operativo Mac Tahoe 26.2 (25C56)Apple Silicon M4STM32CubeIDE 2.0.0 (x86_64, ejecutándose bajo Rosetta 2)AsuntoSTM32CubeIDE se inicia correctamente, pero la selección de texto no se representa visualmente en ninguna parte del IDE (editor, consola, vistas).La selección del mouse y del teclado no muestra ningún resaltado.Copiar/pegar funciona normalmente , lo que indica que la selección existe internamente pero no se muestra.La selección de texto funciona correctamente en otras aplicaciones de macOS.Pasos para reproducir1. Inicie STM32CubeIDE en Rosetta:arch -x86_64 /Aplicaciones/ST/STM32CubeIDE.app/Contenidos/MacOS/STM32CubeIDE2.Abra cualquier archivo fuente.3.Intenta seleccionar texto.Solución de problemas realizadosInstalación de Rosetta 2 verificada.Restablecer preferencias y espacio de trabajo.Espacio de trabajo limpio probado. Deshabilitado el renderizado SWT Metal/gestos a través de opciones .ini.El problema persiste.

Hi,I am using the STM32CubeProgrammer API (v2.20.0) on Windows 11 using the Visual Studio UART example as a base. Everything works fine, however this issue is slowing down the programming workflow.After programming the MCU option bytes to RDP1 (or Closed state on some newer devices), there is a long delay (20 to 30 seconds) during the attempts to reconnect to the device. I already expect that the reconnection attempt will fail, so is there a way to reduce the time or number of reconnection attempts? Or a way to cancel the current operation? The time taken for failed reconnection attempts is 2x longer than the actual programming of the MCU.I noticed that there is a getCancelPointer() function in the API, but I have found no documentation or examples on how to use it. Is it possible to use this or is there some other way?Edit: Added info - using UART to program the device/** * \brief This routine allows to drop the current read/write operation. * \return 0 if there is no call for

Hi!I think a have found a bug in CubeMX for STM32MP257F processor.If you go to RIF - RISAB - VDERAM. You will find that the region size can only be 0x21000. That's more than 128 kB, according to the data sheet.SYSRAM1, SYSRAM2, SRAM1, SRAM2, RETRAM have 0x20000 as maximum region size.Question: If this is a bug, then I want to send a PR to the Github ST repository of the MP2 firmware. Can you guide me where the code is so I can make a PR?

Stm32l010r and s2lp using x cube sub ghz , for custom board just for coding only gpio button status, there are plenty of error, by solving all those 4-5 errors remain and their resolving method is to complete change of middleware files or some code left in file even check through free AI they finally there no such files in middleware add some, for adding it will not compatible with existing file. If tried in stm32wl33cc it also shows so many error but finally there something missing. There are some radio.spi.h and some similar files there in s2lp nucleo example in spirit 2 workshop project, but in s2lp middleware they are not available and look like board specific. If any available example and transmitting and receiving data for s2lp and stm32wl33cc.

Hello STM32 Community, I am facing a persistent "Target no device found" error when trying to program an STM32L073CZT3 custom board using a Nucleo-L073RZ as an external ST-LINK (CN2 jumpers removed). Hardware Setup: MCU: STM32L073CZT3 (custom PCB) Debugger: ST-LINK V2-1 (Nucleo-64) Connection: 5-wire SWD (SWDIO, SWCLK, GND, NRST, VDD_Sensing) Power: External SMPS providing 3.3V (Common Ground established between SMPS and ST-LINK). The Issue: While the ST-LINK pins show correct voltages when floating, the SWDIO (PA13) pin drops to 0V the moment it is connected to the target board. Pin 1 (VDD Sense): 3.3V Pin 2 (SWCLK): 3.29V Pin 4 (SWDIO):  (Measured 2.9V on ST-LINK side connection) Pin 5 (NRST): 3.3V Troubleshooting performed: Verified continuity; no physical shorts found between PA13 and GND. Attempted "Connect Under Reset" and "Hardware Reset" at 480 kHz. Schematic Check: I have a 10uF capacitor (C17) on the NRST line—could this be preventing the debugg

Hello,  I am trying to use a proteus1 to monitor temp and vibration on a spindle and i just cant seem to find the best way to do this. I would  like to use a cloud so I can monitor it off site and get a notification if the temp rises above a threshold. what would you recommend. I have tried the azur cloud i can get the device to connect but then in the classic app i can not get it to send any information. I have tried almost all firmware versions and just cant seem to crack this. Anything will help. Thank you,

Hello everyone.I have recently made my own STM32 board based on the STM32F405. After soldering all the components and testing all pads and connections, finding them to be wired correctly and checking that the 3.3V is being supplied to all the correct pins, I tried to upload some code, but to my shock, the STM32F405 isn't establishing a connection via the ST-Link V2 nor the USB cable. After trying multiple fixes, I suspect the issue might be the STM32F405 chip that I got off AliExpress itself. Before taking any further steps to replace it, I decided to post a question here for review in case the problem was in my PCB design. And sure enough, I had misplaced the chip pin due to the faulty pinout diagram I used as reference.I have since fixed the chip's orientation and rechecked all pad and pin connections, as well as the 3.3V supply, and found everything to be correct; yet I still cannot get the STM32 CubeProgrammer or IDE to connect with my board using the ST-Link V2 or a

Dear ST Technical Support Team,I am currently using the ST1S10PHR buck converter in my custom PCB design to convert 12V input to 5V output.However, the regulator is not switching to the expected 5V output. The measured output voltage remains around 0.79V.Below are the measured and design details:Input Voltage: 12VVIN_SW and VIN_A pins: Confirmed 12V presentEN (INH) pin: 12V present (device enabled)Expected Output Voltage: 5VMeasured Output Voltage: ~0.79VFeedback Resistors: R1 = 11kΩ, R2 = 2kΩInductor: 3.3µHSwitching frequency: Internal 900kHz (SYNC connected directly to GND with short trace)GND and EPAD connected to ground planeOne concern in my PCB layout is that the SW pin to inductor trace length is approximately 47mm. Although the inductor is placed near the IC, the copper routing from SW to the inductor became long due to layout constraints.The board powers up correctly, and all input pins measure properly, but the output remains close to the feedback reference voltage (~0.8V) an

Hi,We are building Linux for STM32MP157D using Buildroot, and we are experiencing an issue where the boot process sometimes does not proceed from BL2 to OP-TEE, and sometimes OP-TEE does not proceed to U-Boot.Occasionally, the kernel does boot successfully.Could this be caused by incorrect DDR3 controller settings? We are using a custom board.If so, would compiling the STM32DDRFW-UTIL source code and using it in engineering mode be the right solution?I have read that for some chips it is possible to perform automatic tuning and receive the optimal configuration as a result.Is this possible in this case? If not, what is the proper method to determine the correct DDR controller settings?If DDR is not the issue, do you have any other suggestions?For testing with DDR-UTIL, I see that there is no development board listed for the 157D series, as the utility supports "STM32MP157C-EV1_DDR_UTILITIES_A7".If we order the "STM32MP157D-EV1", will I be able to run DDR tests on it to compare with our