STM32 MPUs Software development tools

Dear Team,Could you please guide us on how to set the Linux terminal and SSH login password for the STM32MP257F series platform?We would appreciate it if you could share the required steps or documentation for configuring the password.

HelloI am developing a custom board using the STM32MP255F-AKUpdates to the DeviceTree (DT) of a custom board placed in the `mata` layer are not reflected in the build.I have already fetched the source using `devtool modify virtual/kernel`The Device Tree for the custom board is located at .../layers/meta-st/meta-st-stm32mp-addons/mx/ddlskt/..Edit the kernel's DT (stm32mp255f-ddlskt-mx.dts)Add a marker to `model = “...”`: `model=“... AAA”`I tried building it$ bitbake virtual/kernelWrote Image.gz, *.dtb, and modules to the SD card and booted(brd-ddlskt) # cat /proc/device-tree/modelSTMicroelectronics custom STM32CubeMX board - openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06AAA has not been added to the modelRunning `cleansstate` before building will reflect the updated device tree$ bitbake -c cleansstate virtual/kernel$ bitbake virtual/kernelWrite Image.gz, *.dtb, and module

Hi everyone,I'm trying to install the EGit plug‑in on STM32CubeIDE version 1.14.1, but I'm running into persistent issues.During the installation, the dependency calculation phase fails, and CubeIDE proposes alternative solutions. If I continue using the option to keep the original installation and modify only the required components, the process eventually ends with an installation error.The exact same problem also occurs on STM32CubeIDE version 2.0.0, so it doesn’t seem related to a single release.Below is the full error log I receive:An error occurred while collecting items to be installedsession context was:(profile=STM32CubeIDE,phase=org.eclipse.equinox.internal.p2.engine.phases.Collect, operand=, action=).No repository found containing: osgi.bundle,javax.annotation,1.3.5.v20230504-0748No repository found containing: osgi.bundle,org.eclipse.emf.common,2.29.0.v20230916-0637No repository found containing: osgi.bundle,

Hi ST Dev team!I have found that LSE is mandatory when building a new custom board. If not LSE is mounted and configured, then both TF-A and Op-tee will complaining about clock ID 5, which is LSE.Here is a walk around for Op-tee by removing the &clk-lse.https://github.com/DanielMartensson/Watermelon-Wine-1A/blob/linux-testing/watermelon-wine-os%2Fcubemx%2FCA35%2FDeviceTree%2Ffirmware%2Foptee-os%2Fstm32mp257f-firmware-mx.dts#L497-L498And for TF-A, ut must need some modification inside the code:

Due to absence of a security forum for MPU's (while there is for MCU's) posting this here.The CRA prohibits products with known CVE to be placed or made available on the EU market.The ST Yocto ECO 6. Scrarthgap currently has 632C CVEs. The latetst Yocto master has 13.As such,1. how to place a product on the market while a distro without known CVE's does not exist ? A company may have great documentation and processes but if the actual supplied software has known CVE's there isn't a to place it on the market2 Many devices may use even older  ECO systems (5.10) images which may have even more CVE. How will there get patched ?3. Where can information about the known CVE's in ST kernel , U-Boot, OPTEE and TF-A (dev packages) be found ?

Hi,i tried to migrate my project to CubeMx v6.17.0 coming from v6.16.0As a result, the firmware package was also updated to FW_MP1 V1.7.0I am using CubeIDE 2.0.0After migration the compilation fails with following error in auto-generated FreeRTOSConfig.hDescription Resource Path Location Type each undeclared identifier is reported only once for each function it appears in FreeRTOSConfig.h /PROJECT_CM4/Inc line 71 C/C++ Problem/* USER CODE BEGIN Header */ /* * FreeRTOS Kernel V10.6.2 * Portion Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. * Portion Copyright (C) 2019 StMicroelectronics, Inc. All Rights Reserved. * * Permission is hereby granted, free of charge, to any person obtaining a copy of * this software and associated documentation files (the "Software"), to deal in *

Dear all I was setting up the RISAF4 for STM32MP257, however, the partition with name "linuxkernel2" has a glitch where its size shows as givenWhich is beyond the size of my LDDR4 set to 8Gb.How to solve it? A quick reply will be appreciated.Thanking you!With regardsAmit 

Dear ST Team,I Need the clarification can I use YT9218MB in place of RTL8211F-CG ,Please recommend me , If we can then we need to use OpenWRT

Hi!I think a have found a bug in CubeMX for STM32MP257F processor.If you go to RIF - RISAB - VDERAM. You will find that the region size can only be 0x21000. That's more than 128 kB, according to the data sheet.SYSRAM1, SYSRAM2, SRAM1, SRAM2, RETRAM have 0x20000 as maximum region size.Question: If this is a bug, then I want to send a PR to the Github ST repository of the MP2 firmware. Can you guide me where the code is so I can make a PR?

Hi there, I want to flash a HEX file using a Raspberry PI. So I followed the steps described here.But if I run this line:$> ./SetupSTM32CubeProgrammer-2.13.0.linuxI get the message:bash: ./SetupSTM32CubeProgrammer-2.13.0.linux: cannot execute binary file: Exec format errorHas someone an idea why this is not working?Im running Raspbian GNU/Linux 11 (bullseye)

Hello everyoneWhen I add OpenAMP to Pinout & Configration of .ioc and build it, the build failsThe steps are as follows:Create a new project (fuga_oka) for STM32MP277F-EV1 in STM32CubeIDEBuild this project. The build will finish successfullyAdd OpenAMP to this projectOpen fuga_oka.ioc                   - Select OPENAMP in Pinout & Configration -> middle ware & Software Packs         - Check M33NS(Cube)         - Also check Activated         - Save fuga_oka.iocBuild the project. Some errors will be reported and the build will failAn excerpt of the error part of the build log. The raw log is attached separately~~~C:/STM32MP2xx/fuga_oka/Middlewares/Third_Party/OpenAMP/libmetal/lib/system/generic/condition.c:12:10: fatal error: metal/c

Hello,I have some sort of experience working with linux on RPI.I wanted to increase my embedded linux experience with STM32MP.So I wonder, should I buy STM32MP2 because its newer, or STM32MP1 because it will probably have more support and more reference because its been here for some time now?Also, for STM32MP257F-DK, the debug port and the power supply are shared on the same USB-C, how can i do both at the same time? because I don't think the PC can supply it with enough powerWould I need anything to start other than the external USB-C power supply?Any other recommendations are welcome

Despite my best efforts to populate and boot the the image of the STM32MP157-DK2 using the .tsv files I am met with a mixed result To date I have yet to establish a USB connection despite following the procedures at wiki. The UART connection is working. My environment is as follows ...Ubuntu 24.04.4 LTS - stm32mp1-openstlinux-6.6-yocto-scarthgap-mpu-v26.02.18 - STM32CubeProgrammer v2.22.0 and STM32_Programmer_CLI Be it that I use STM32CubeProg or the STM32_Programmer_CLI terminal interface the FlashLayout_sdcard_stm32mp157f-dk2-optee.tsv is not found despite the path being correct. Yet I am able to flash tf-a-stm32mp157c-dk2-optee-programmer-usb.stm32 0x01 or tf-a-stm32mp157f-dk2-optee-programmer-usb.stm32 0x01 using the terminal which was the first value in a sequence of the .tsv file (see kate as an example). The same conundrum occurs using STM32CubeProg. Might you suggest how I might resolve this problem - be it in establishing a USB connection or f

经我这三两天的多次调试，我终于找到了问题所在先说segger rtt viewer的工作方式首先，我将segger rtt的源码编译烧录到stm32mp257d_m33那里去。这时m33核的暂存会持有一个_segger_rtt结构体。然后我将这个结构体地址提供给segger rtt viewer，这时就会成功建立起通讯现在我通过segger rtt viewer向stm32mp257d_m33发送数据，这时jlink这个硬件工具就会通过swd直接操作暂存将数据写入到_segger_rtt结构体的下行缓冲区，按理会同时更新_segger_rtt结构体下行缓冲区的写位置WrOff而我在stm32mp257d_m33的用户代码逻辑是，将从swd收到的数据即刻原封不动的发还回去下面是我实际使用segger rtt viewer时的输入输出窗口的内容00> WrOff=557, RdOff=557, HasData=000> WrOff=557, RdOff=557, HasData=000> WrOff=557, RdOff=557, HasData=000> WrOff=557, RdOff=557, HasData=000> WrOff=557, RdOff=557, HasData=000> WrOff=557, RdOff=557, HasData=000> WrOff=557, RdOff=557, HasData=000> WrOff=557, RdOff=557, HasData=000> WrOff=557, RdOff=557, HasData=0< 55600> WrOff=557, RdOff=557, HasData=000> WrOff=557, RdOff=557, HasData=000> WrOff=557, RdOff=557, HasData=000> WrOff=557, RdOff=557, HasData=0

It's telling me (for example) there's a "Path Entry Problem":Invalid project path: Include path not found (C:\Users\xxx\Documents\xxx\USB_CDC\USB_Device\Target).The Tool Settings / MCU GCC Compiler / Include paths contains"${workspace_loc:/${ProjName}/Application/USB_Device/Target}"and in my project there is a folder Application/USB_Device/Target, it links to a folder C:\Users\xxx\Documents\xxx\USB_CDC\STM32CubeIDE\Application\USB_Device\TargetHow can I figure out where this warning is coming from?(notice - the project builds just fine, it's just a warning, but company policy is to build without warnings)

I was excited to see the Rust support for the Developer Package (seen here and here)However, I am having some issues with the fact that the provided toolchain is version 1.75 rustc and cargo. Mostly the fact that this version cannot use dependencies which use Rust edition 2024.I know I can go through dependencies one by one and downgrade them to earlier versions until there are no edition 2024 dependencies, but this is pretty tedious and doesn't seem like a great solution in the long run.Is there any chance that the MP2 Dev Rust addon could be updated to a more recent version?Or if that isn't possible, is there any advice on other ways to update the provided toolchain or create a custom rust toolchain using th

Hi STM32Community,i am currently trying to build openSTLinux using the STM32CubeMX (6.17.0) generated device tree files with the yocto build process.For this I am using the STM32MPU Distribution Package. (stm32mp-openstlinux-6.6-yocto-scarthgap-mpu-v26.02.18)I set up the Distribution Package according your Wiki Installing_the_OpenSTLinux_distribution and I have set up the STM32CubeMX Project according How_to_create_your_own_machine  :I created the STM32CubeMX project directory "mx" /layers/meta-st/meta-st-stm32mp-addons and generated the project filesI created a new machine config file under /layers/meta-st/meta-st-stm32mp-addons/conf/machine, using the examp

Hello everyone,I'm a beginner in the STM32 world,A teacher has lent us a STM32MP157C-DK2 board (with a A7 and  a M4) for a challenge,and I am currently trying to upload a program for the MCU (a button which switches the color of a RGB LED).As I'll first describe my complete setup and what I have already done, so you can directly go to the end of the post if you want to see the main problem I'm facing which is :To "import an OpenSTLinux Project" into cubeIDE,to ultimately update the device tree of the Cortex-A7 into cubeIDE.My setup:A x64 computer running on Windows 11 with WSL 2 Ubuntu 24.04.01 LTS.The STM32MP157C-DK2 board connected to my PC with ST-LINK and by network.On WSL :I downloaded