STM32 MCUs Embedded software

Hello, is it possible to boot FSBL and load application from SD card upon powerup, bypassing onboard flash?  I didn't see any clear guides on this procedure.Thank you

In testing the LoRaWAN_End_Node_LBM application supplied with STM32CubeWL-1.5.0 release I found that the output power is substantially lower than the same test setup with the LoRaWAN_End_Node application supplied with STM32CubeWL-1.4.0.  This testing was conducted only using the US915 region setting.First I found that the EIRP was being defined as 16 dBm in Middlewares/Third_Party/LoRaWAN/smtc_modem_core/lr1mac/src/smtc_real/src/region_us_915_defs.h when it should be 24 dBm.#if defined( LR11XX ) || defined( SX1262 ) || defined( SX1268 ) // region is 30 dBm but radio is 22 dBm ERP (+2 to EIRP) #define TX_POWER_EIRP_US_915 (24) // define in dbm #else // region is 30 dBm but radio is 14 dBm ERP (+2 to EIRP) #define TX_POWER_EIRP_US_915 (16) // define in dbm // TODO must be checked, SX126x dependent for the max power #endifSince the project compiles with the preprocessor symbol

@FBL Can you explain me about buffer descriptor table (BDT)? Is it fixed?I have got behavior that I can't explain.Dumping packets on host I got wrong data. Length is ok, but data is wrong.In BDT I wrote correct address and length. Data wrote in pma (adress that is in BDT) is correct.But when I stop in debugging address in BDT is changed. As I think in BDT there is a place for each endpoint (or it is like cyclic buffer?)What I found if I set break point with "if" condition, just before sending address in BDT is OK, and data on host is OK. It seems to me that I am working incorrectly with BDT.

I am coding from the scratch to learn how STM32 works with MIPI-DSI LCD, because I am going to use customized MIPI-DSI LCD. I refer to the official code, but some incorrect content as below:official default code: in main.c , static void MX_LTDC_Init(void):// SETVCOMuint8_t InitParam60[4] = {00, 00, 00, 0xC0};if (HAL_DSI_LongWrite(&hdsi, 0, DSI_DCS_LONG_PKT_WRITE, 4, 0xC7, InitParam60) != HAL_OK){Error_Handler();}BUT, I check HX8379C datasheet (LCD control ), SETVCOM command is (B6h), and there is no 0xC7 command ?so what's this code for? and HX8379C datasheet dosen't mention initial sequence , how do we know that we need to set SETPOWER, SETD

I am trying to capture data from the LINE_IN (blue jack on board), but I am not receiving the correct input. I evaluated my output at the oscilloscope and noticed that I am not receiving the sinusoid I am injecting; the frequency is correct, but the data appears clipped, as shown in the picture. I tried to reduce the Vpp, but it just started getting noisy instead of giving the correct input.My second test was to record on the sd card, and the problem persisted; I am only getting data above zero and noise

Dear community members,STM32H7S78-DK: USBX standalone (CDC ACM + PIMA) works in HS now but PIMA / MTP is not supported in standalone mode in USBXCurrently, it is not possible to use the PIMA/MTP class in USBX in standalone mode (without an RTOS). The MTP implementation depends on Azure RTOS ThreadX, and there is no official support for running it in bare-metal configurations.When attempting to use it in standalone mode, the stack returns:#define UX_FUNCTION_NOT_SUPPORTED 0x54This is also reflected in the official documentation:USBX Getting Started – Bare-metal support matrices 

Hello,   I configured TIM5 to generate a signal out to a pin using STM32CubeMX2 for a Nucleo-C562RE board. I enabled the EXTI interrupt for the pin in the timer configuration to get EXTI6 interrupts on the falling edge. I also enabled the use of register callbacks for EXTI. The problem that I am having is that I cannot find the function to retrieve hEXTI6 to register the EXTI callback. I looked in the mx_tim5.h/c and in mx_gpio_default.h/c. I had no problem getting the EXTI handles for GPIO EXTI (for example mx_gpio_default_exti7_gethandle()) and getting TIM handles (mx_tim5_gethandle()).   To make the code work I had to add mx_gpio_default_exti6_gethandle() prototype to mx_tim5.h and the implementation below to mx_tim5.c:   hal_exti_handle_t *mx_gpio_default_exti6_gethandle(void) { return (&hEXTI6); }  

Hey there,I'm currently trying to port a project that I was using successfully on the STM32U5A5, to the STM32N657.The project utilises the PDM2PCM library to convert a PDM audio stream received from a MEMS microphone via the SAI interface of the MCU into PCM audio data. It is based on an example from the STM32U3 MCU firmware package (STM32Cube/Repository/STM32Cube_FW_U3_V1.3.0/Projects/NUCLEO-U385RG-Q/Examples/SAI/SAI_AudioRecord_PDM), parts of which I have incorporated into my own application on the STM32U5A5.I'm now trying to port this project to the STM32N657 on a NUCLEO-N657X0-Q board. I've found the matching PDM2PCM library for the N6's M55 core in the X-CUBE-AUDIO-KIT as mentioned here.Now, when I integrate this library (libPDMFilter_CM55_GCC_wc32.a) into my project and start the debugger of th

Hi ST Community, I'm facing a critical and reproducible hardware JPEG encoding issue on the STM32N6. The JPEG encoder only works correctly when the image width is exactly 800 pixels. Any other width I've tested — including 480, 960, and 960x480 — causes the hardware to fail in exactly the same way. Height variations do not affect the outcome; the problem is solely tied to the row width. Environment: MCU: STM32N657xx (STM32N6-DK board) Firmware Package: STM32Cube FW_N6 V1.3.0 IDE: STM32CubeIDE Image Format: RGB565 input → YCbCr 4:2:0 subsampling, Quality

  I had some issues configuring H573 with CubeMX.When I configure TIM2 or TIM3 according to the instructions of RMII_PTP_Synchro in CubeMX I cannot enable the RMII PTP functionality.And when looking at RM0481 it seems that the description of the relationship between these two timers and ETH MAC is a bit vague.What configuration is required to enable RMII_PTP_Synchro on H573?

Hi Forum! Previous experiments, but it still could not work, I have no idea how to fix this problem:https://community.st.com/t5/stm32-mcus-embedded-software/hmd-application-stm32f1-with-bno055-via-vcp/td-p/876235 Therefore, I revisited the literature review. I found this paper from meta oculus, they using the HID to transfer the IMU data, so I want to imitate their steps. (using notebookLm to learn it )https://msl.cs.illinois.edu/~lavalle/papers/LavYerKatAnt14.pdf HID read/write tool(software)https://github.com/benbaker76/SimpleHIDWrite  Prob

Hello ST,I'm trying to communicate the STM32F411RET6 with IMP34DT05 mic, i have enabled the I2S in ioc configuration, i have downloaded and added the library file from https://www.st.com/en/embedded-software/x-cube-memsmic1.html, while building the project getting 15000+errors coming, i'm assuming this library file is incorrect, could you please review as attached and provide Specific working library for this project.Advance Thanks,Sridhar. 

Hello ST community, I configured my project in STM32CubeMX 6.17.0 and use STM32CubeIDE 2.1.1 to debug. The goal of the program is to receive a raw ethernet frame.I followed this tutorial, of course I adapted the pins to NUCLEO-N657X0-Q, and I skipped the part with the transmission, I didn't change anything in the HAL_ETH functions. I am sending from the PC (I can see that the frame is sended with wireshark):from scapy.layers.l2 import Ether from scapy.packet import Raw from scapy.sendrecv import sendp #Terminal ipconfig /all dst_mac = "00:80:E1:00:00:00" src_mac = "AA:79:39:37:92:EA" payload = bytes([0x01] * 86)

Hello,I am facing an issue with the STM32C5 HAL SPI driver related to CRC error detection.In my setup, CRC is enabled for SPI. When a CRC error occurs, I can observe that the CRCERR flag is set before the transfer is closed. However, the CRC error is never reported via the HAL error callback.Looking into the HAL implementation, I noticed the following behavior:SPI_CloseTransfer() calls LL_SPI_Disable()After disabling SPI, SPI_CloseTransfer() checks LL_SPI_IsActiveFlag_CRCERR()When this check is performed after LL_SPI_Disable(), the CRC error is no longer detectedIf I move the LL_SPI_IsActiveFlag_CRCERR() check before LL_SPI_Disable(), the CRC error is detected correctlyAdditionally, in my case SPI_CloseTransfer() is called from HAL_SPI_IRQHandler(), but:the return value of SPI_CloseTransfer() is not evaluatedonly the Tx/Rx complete callback is invokedmy error callback

This is an improvement request post.STM32 HAL on every family has tons of following code constructs:tickstart = HAL_GetTick(); while (!condition) { if ((HAL_GetTick() - tickstart) > TIMEOUT_VALUE) { return HAL_TIMEOUT; } }When using HAL with (Free)RTOS or interrupt based scheduler, then these while loops delay same priority tasks (until time-slicing kicks in), block everything that has lower preemption priority, waste energy (crucial for battery powered devices) and decrease responsiveness.There are multiple ways to improve it. One of the simplest is to supplement non-critical* loops with optional user-definable yield macros.__weak void HAL_Yield(void) { } tickstart = HAL_GetTick(); while (!condition) { if ((HAL_GetTick() - tickstart) > TIMEOUT_VALUE) { return HAL_TIMEOUT; } HAL_Yield(); }Now user can im

Hi everyone, I am currently developing an image capture project using the STM32N657 (Cortex-M55) and have encountered an extremely bizarre DMA2D write issue (a silent failure). Goal: Use DMA2D (M2M_PFC) to convert an RGB565 buffer to RGB888 and write it to CPUAXI_RAM1 (0x34080000). [Problem Description] I wrote a "minimal isolation test" to bypass all camera/GPDMA variables. I forced the CPU to fill the source buffer with pure white (0xFFFFFFFF), and then manually triggered the DMA2D to transfer it to the destination buffer. The Result: The DMA2D finishes successfully. The DMA2D->ISR register reads 0x00000002 (the TCIF Transfer Complete Interrupt Flag is set, and there are NO Transfer Errors). However, the destination buffer remains completely filled with 0x00000000. [Troubleshooting Done] To isolate the issue, I have verified the following, but t

Title edited to clarify this is about CMSIS-RTOSHello, everybody!I don't know where to look for information on which CMSIS versions are supported by specific STM32 microcontrollers. I asked one of the ST employees and STM32 Sidekick about this, and I got no definitive answers.STM software tools confuse me further. For example, STM32CubeMX (6.17.0) allows me to choose CMSISv2 the interface for FreeRTOS in my STM32F769I‑DISCO board project, but LwIP in the same project does not see the operating system used unless I change the CMSIS version to v1 (you can find more details about this specific issue in this thread). I couldn't find any document that would say which interfaces are supported by LwIP either.That's why I would like to ask You, where should I look for informat

I configured a nucleato-L152RE LED program using CubeMX6.17+STM32L1 Firmware Package V1.10.6 and found that the program kept restarting automatically. After adding the following code to the SystemInit() function generated by CubeMX, the problem was solved. What is the reason for this? And my other projects never need to include this line of code, such as F103, F411, G431, L051, and so on.SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET;

Dear all,I have a working camera + video encoder solution running with LCD display disabled.I have one preview thread that displays camera data on the LCD, this thread can be suspended and restarted. While the first run looks fine, the output has a green tint from the second start on:First iteration: Second+ iteration:

Hello STM Community,I am a beginner working with the STM32H7B3I-EVAL evaluation board based on the STM32H7B3LIH6Q MCU, and I am currently setting up my development environment on Ubuntu 24.04.3 LTS.I installed STM32CubeIDE 1.18.0 using the following installer:st-stm32cubeide_1.18.0_24413_20250227_1633_amd64.sh.zipI am facing a few issues and would really appreciate your guidance.1. Need existing demo codes for STM32H7B3I-EVALI would like to get the existing/demo example codes available for this board, especially the examples related to the firmware version currently flashed on my board, which shows:Firmware Version: V1.0.1Could anyone please guide me on where to find the exact demo code corresponding to the factory-flashed board behavior, if available?I am specifically looking f

Hello, What HAL2 API can I use to turn on/off the output of a timer? In HAL (ver 1) this could have been done like this:TIMx->CCER &= ~TIM_CCER_CC1E; // Example for Channel 1: ~TIM_CCER_CC1E // or __HAL_TIM_MOE_DISABLE(&htimx); Thank you,-Gil

I've been using a nucleo l476rg with a LIS2DUX12 sensor and I need to use the SPI protocol, but came as a surprise that the MISO line is not working. When it's not getting 0xFF (should be 0x47), gets inconsistent values. Tried changing CPHA, CPOL, prescale and none of that is working.// 1. Tx and Rx arrays uint8_t tx_wakeup[2] = {0x3E, 0x01}; // Register 0x3E, value0x01 (Soft Power-Down) uint8_t tx_whoami[2] = {0x8F, 0x00}; // Read 0x0F (WHO_AM_I) uint8_t rx_buffer[2] = {0x00, 0x00}; char msg[50]; HAL_Delay(100); // Wake up sequence HAL_GPIO_WritePin(GPIOB, GPIO_PIN_6, GPIO_PIN_RESET); HAL_SPI_Transmit(&hspi1, tx_wakeup, 2, 100); HAL_GPIO_WritePin(GPIOB, GPIO_PIN_6, GPIO_PIN_SET); // Read who_am_i HAL_GPIO_WritePin(GPIOB, GPIO_PIN_6, GPIO_PIN_RESET); //HAL_SPI_TransmitReceive(&hspi1, tx_whoami, rx_buffer, 2, 100); HAL_GPIO_WritePin(GPIOB, GPIO_PIN_6, GPIO_PIN_SET); // print data sprintf(msg, "WHO_AM_I = 0x%

Hello my friends, I hope you are doing great.I am trying to create a custom driver for UART peripheral with CMSIS register header files.I have created a build system using the board files and linkers and make. So far I have been able to make drivers for the GPIO pins.Now I am trying to create my own driver for the UART peripheral via the CMSIS. So far I have created this: int uart_params_init(uart_t *uart){ if (!uart) return -1; // defualt configs: uart->tx_pin = 9; uart->rx_pin = 10; uart->baudrate = 115200; uart->tx_port = GPIOA; uart->rx_port = GPIOA; uart->instance = USART1; uart->tx_af = 1; uart->rx_af = 1; return 0; } int uart_init(uart_t *uart) { if (!uart || !uart->tx_port || !uart->rx_port) return -1; if (uart_initialized) return 0; // Enable GPIO clocks for the port: if (uart->tx_port == GPIOA || uart->rx_port == GPIOA){ RCC

Hi, I am using the STM32N6570-DK development kit and I want to flash my FSBL and Application firmware into external flash using USB. Currently, I am able to flash the firmware using ST-LINK, but I want to perform flashing through USB as well. I configured the boot pins as mentioned in the datasheet: BOOT0 = High BOOT1 = Low Current beha

 Hey ST-Community,I’m working with an STM32H7S78-DK board and trying to get Ethernet running. TouchGFX and FreeRTOS are working fine, but I’m stuck with lwIP. The task starts, but DHCP never succeeds (the printed IP is always 0.0.0.0). I also tried with a static IP, but I still can’t ping the board. Deactivating TouchGFX didn't help.I've followed this video: STM32 : How to Get an IP Address via DHCP on STM32H7S78-DK with LwIP using IAR EWARMLwIP has the following memory settings:MEM_SIZE = 14*1024BytesTCPIP_THREAD_SIZE = 4 * 1024BytesI've configured the MPU as well following the given Video.I’m not sure where to look next – maybe I’m missing some configuration step? Has anyone successfully used lwIP with this board and could give me a hint?Thanks a lot in advance!