STM32 MCUs TouchGFX and GUI

I have made a dynamic menu made with a listLayout with a number of buttons inside a scrollableContainer. When a user push the buttons the listLayout is updated with new content.I have not been able to have the scrollbar reflect the size of the listLayout after the listLayout is updated. The scrollbar will only update when the user starts scrolling through the new content. Until then it reflect the precious size of the listLayout.I have tried:scrollableContainer1.doScroll(0, 180);Thinking it would have the same effect as the user scrolling the scrollableContainer, but it does not work.Is there a way to force update of the scrollbar?

I am a software developer working for a company that plans to use TouchGFX for its display solutions.We are currently integrating TouchGFX into an existing IAR-based project and want to use our own display and DMA drivers instead of the CubeMX-generated setup. While TouchGFX initializes and runs partially, we are facing a critical issue where several expected callbacks are never triggered.Problem descriptionThe following methods are never called during runtime:TouchGFXHAL::flushFrameBuffer(const touchgfx::Rect& rect)OSWrappers::takeFrameBufferSemaphore()OSWrappers::giveFrameBufferSemaphore()Our TouchGFX thread performs all required initializations, passes our custom LCD

Hello everyone.I am doing a TOUCHGFX project with STM32H750IBT6, W25Q512, IS42S32400F-6TL. I took my first screen printout and the image came out shifted. I am using my screen vertically by rotating it 90 degrees in Touchgfx Designer. I still haven't solved the problem. I would be very happy if you could help me.

The screen has 4 containers and many widgets. I am interested in keeping the names during the export to save lot of repertitive work

I'm currently using an STM32H7S78-DK, and I'm correctly able to run TouchGFX with FreeRTOS and everything. I also an error handler function that, in case of a crash of TouchGFX it writes directly to the framebuffer.Now, I would like to do a similar thing but on the boot code, so basically before the classic jump if (BOOT_OK != BOOT_Application())I have an external RAM mapped at the address 0x90000000 which works correctly in TouchGFX with .icf likedefine symbol __region_EXTRAM_start__ = 0x90000000; define symbol __region_EXTRAM_end__ = 0x91FFFFFF; define region EXTRAM_region = mem:[from __region_EXTRAM_start__ to __region_EXTRAM_end__]; place in EXTRAM_region { first section TouchGFX_Framebuffer , section Video_RGB_Buffer , section Nemagfx_Stencil_Buffer };I wanted to use the same section of memory in the Boot, accessing the framebuffer directly, so I edited th

 Hardware ConfigurationMCU: STM32F469NIH6Custom Board: Pin-to-pin replica of STM32F469I-DISCODisplay: HF-35040-X365-A0 (3.5-inch, 800x480 RGB parallel interface)SDRAM: IS42S32400J/F (16MB, 0xC0000000)Interface: LTDC (NOT DSI - DSI explicitly disabled)Framework: TouchGFX 4.26.0Working ReferenceThe same display works perfectly on STM32F429 with the same LTDC configuration, so the display hardware is confirmed functional.Problem DescriptionThe display continuously shows RGBW color cycling (white → red → green → blue, repeating every ~1 second) instead of rendering the TouchGFX UI.Critical o

Touchgfx 4.26.0 (and was same on 4.24.0) keyboard examples are the same resolution although there are (3) resolution of display resolution selectionsThey all display the keyboard size as approx. measured 43 mm (1.7 inches) X 33mm (1.3 inches) on a 5-inch display 800 X 480 resolution. To be usable we believe the keyboard needs to be about 1.5 to 2 times larger than present. (about 25% LARGER) See details in pdf attachment

I’m working with TouchGFX in STM32CubeIDE. After creating a new project and copying over the IOC file and pin configuration from the verified design used for my custom PCB, I’m now running into errors. Some components fail to build, and I’m getting “file not found” errors for certain header files—even though the files clearly exist and I can open them in the IDE.Do you have any suggestions for fixing include paths or linker settings to resolve this?  

I'm very new to this so be kind.  I've been working on a display for CAN data.  I have the display designed and it works and while building code for the CAN and using the GPIO5 LED for testing, when I Run it, I get a garbaged display.  I have a working sample project that was provided to me as a guide, when I run it, it works fine, but when I go back to my project, part of the other project is still being displayed.  It's as if it's not fully erasing and programming everything.  I did some research and found suggestions to select Full Chip Erase, but there isn't one. 

Right now, if there are any widgets on a page the Designer automatically creates a canvas buffer for it.  The following code is created in the ViewBase .hpp/.cpp files static const uint32_t CANVAS_BUFFER_SIZE = 12000; uint8_t canvasBuffer[CANVAS_BUFFER_SIZE]; touchgfx::CanvasWidgetRenderer::setupBuffer(canvasBuffer, CANVAS_BUFFER_SIZE);   This gets set up for each view that has widgets.  I want it to STOP DOING THAT.  I want to allocate my own buffer to it, in a piece of ram that I choose.  Please, please, please give me the option to tell the Designer that I will handle it myself.I can allocate my own buffer in the TouchGFXHAL::initialize() function, but it's just going to get overridden as soon as a View gets, as that constructor will set up it's own function. This is especially important, because I have give it a buffer at the sta

Hello,We have procured a STM32U5G9J-DK1 discovery kit. We are in need of the default pre-loaded program that comes with the kit as this will help us to understand how to use Touch display and its other features. We see that this pre-loaded program is not available in the repository downloaded for STM32U5G. Therefore, request you to kindly share it here.With regard,Sudarshan Chaudhary

Hello ST Community Team,I am facing a TouchGFX project generation issue related to path mismatch while working on an STM32H745 dual-core device – unable to locate .ioc / .cproject ?I am sharing my setup and issue details below.  Environment Details:STM32CubeIDE: 1.17.0TouchGFX: 4.25.0X-CUBE-TOUCHGFX: 4.25.0Controller: STM32H745XIH3Core Used: CM7Toolchain: STM32CubeIDEOS: Windows Issue Description:I have written application code for Core-M7, and when I try to generate images / assets using TouchGFX, the generation fails during Post Generate Target.Error observed:Post Generatetouchgfx update_project --project-file=simulator/msvs/Application.vcxprojDonePost Generate Targettouchgfx update_projectUnable to locate D:/WORKSPACE_APPLICATION/LPOCIP_090126_1430_PM/LPOCIP_SCRATH_jumper_QSPI_APIS_SWETHA_UPDATED_QSPI_SDRAM_CAN_P

I'm experiencing a HardFault that occurs always on cold boot (after the board sits unpowered for ~1 hour). It also occurs sometimes when flashing and immediately running from the debugger.I'm using FreeRTOS, and I've noticed that commenting a task, flashing the new firmware, no hard faults. De-commenting the same code, flashing again, problem solved (with debugger on).I exit the debugger and try to power cycle the device, all works.After the board sits unpowered for a certain time and I try to turn it on, Hard Fault again.The issue is always the same CFSR.IMPRECISERR (imprecise data access error)I managed to have a call stack and the assembly codeCFSR.IMPRECISERR (imprecise data access error) PC = 0x70017DD2 Stack trace: HardFault_Handler <Exception frame> touchgfx::LCDGPU2D_AXI::blitCopy

Hi,I have 3 radio-buttons in a custom container which is present on several screens.I would like the radio-buttons to keep their states between when switching screens.I have the radio-buttons states reported to the model every time a button is pressed and when the screen changes, the new active view fetches the radio-button state.However, I do not see a function to update a radio-button state without triggering the button action.Is there such a function?

I'm currently using Touchgfx after updating from version 4.25 to 4.26.When I build and run the code generated by Touchgfx 4.26, Display color doesn't match the design in Touchgfx 4.26.But When I do the same thing through Touchgfx 4.25, Display color matched very well. 

Hi,I'm trying to drive a 5 in LCD with STM32H757. However the MCU's internal RAM is too small for the frame buffer for this 800x480 LCD. So I have a PSRAM APS6404L on the QUAD SPI bus. I have succeeded in setting the memory mapped mode for reading the PSRAM, but I don't know how to integrate the custom write routine for the touchGFX. The MX configurator seems not allow me to set up a partial frame buffer in the internal RAM. I have tried to use custom LCD type to forcefully set the partial frame buffer, but I'm unable to get the touchGFX task to run.Does the custom LCD type require lot of work? I feel so stuck right now. Please help. Thank you.

Dear ST Community Team,We are currently working on a project using the STM32N657X0H3Q1 microcontroller and developing the GUI application with TouchGFX.While configuring and generating the TouchGFX project, we are encountering RAM and ROM overflow errors during compilation/linking. The internal SRAM and Flash available on the STM32N657 device are not sufficient to accommodate the TouchGFX framework, graphics assets, and application code.As an alternative solution, our hardware design includes the following external memories:External RAM: S80KS5123GABHB020External Flash (Octal SPI NOR): S28HS512TGABHM0100

Hello all,Trying to set up the custom display on the STM32H750B-DK dev board.Interestingly, the display works via LTDC functions in Keil just fine... but I do not have much luck with the TouchGFX. For example, started with setting up the TBS in the Designer to avoid the complications of memory and other configurations (thanks to the ST support) and continuing in the CubeIDE where I have opened the .*.ioc file to update the MX configuration for the LTDC and TouchGFX... it compiles ok, I can opend the TouchGFX designer and "upload" the picture, for example, I can see the picture to be in the memory. See attached build memory analyzer.However, when I run the application or debug, I cannot see the preview of the picture.One of the ideas, as it is explained in the TouchGFX manual, namely Board bring up, would be to preview a simple framebuffer, not sure how easily that would be?I am not sure how to tackle this problem, so any comments, ideas, or hints a

Hello,I'm using the board NUCLEO-H563ZI paired with RVA35HI screen.When I just created the project and generated the code i could download the touchgfx project with the touchgfx application ("program and run target" option), but after trying to download it with IAR IDE (and having problems with it) the system is not working anymore; the screen stays white and when i try to generate with cubemx, the popup message on touchgfx asking if i want to reload after the changes is not showing up anymore.It seems that touchgx and cubemx aren't synchronized anymore.When i said i have problems with IAR i mean these messages when i try to debug:1- "There were warnings while generating flash loader input. See the Debug Log window for details"2- "There were 2 errors and 1 warning during the initialization of the debugging session. There is more infrmation in the Debug Log window. Do you want to continue the "Run to" command?"The dubugger stops in the&

 Hi all I have STM32 IDE installed in "C:\STM\STM32CubeIDE_1.19.0\STM32CubeIDE" and seem to work properly so far as I am on installing the 2 programs. I try to install TouchGFX 4.26.0 in "C:\STM\ to have those two in the same area., but I received an errorlike this one: Could not set file security for file "C:\STM". ERROR 5.........So anyone have an idea ?Thanks all.

Hello,I am trying to run a touchscreen with STM32H7R7L8Hx and I am having multiple issues.This is the structure I used, I am using FreeRTOS and TouchGFX in the STM32CubeMX. Years ago I run a touchscreen with STM32H7A3RITx, it was easy because it was not asking project structure.

Hey, our team is working with TouchGFX Designer (4.19.1) and IAR IDE.TouchGFX assets include 50 MB of images, videos, fonts and texts.We are trying to find a way to change the app without touching and flashing TouchGFX assets.The TouchGFX should stay constant while only the app code itself changes.Meaning compiling the code without compiling TouchGFX assets again to get a smaller hex file to flash/store, and current TouchGFX assets that are stored in the external memory will work, so basically we want to exclude all TextFlashSection, ExtFlashSection and FontFlashSection files from compilation.The main goal is to store a backup version of the code inside the internal flash for cases of software updates, so we want to compile only the app code.Is it related to the linker file or some other configuration file?

Dear ST Support Team,We are currently working with the STM32N657X0H3Q1 controller and configuring TouchGFX to use an external RAM device.The external memory used in our design is S80KS5123GABHB020 (512 MB Octal RAM) connected via XSPI. The external RAM is intended to be used for TouchGFX frame buffers and graphics-related data.While configuring TouchGFX with the external memory in STM32CubeMX / application code, we need to set the base address of the external RAM. However, we would like clarification on the following point:What is the correct memory-mapped base address that should be configured for the external RAM (S80KS5123GABHB020) when used with the STM32N657X0H3Q1 for TouchGFX ?Is this address fixed by the STM32N6 memory map, or does it depend on the XSPI instance and configuration (XSPI1 / XSPI2)?

Is there any example how to create any simple animation? I would like to get object in motion using static isometric view. Object based on the few outlines of rectangles outlines with painter or putting the texture on it. I need to rotate one pseudo 3D rectangle in reference to the other. It is not so hard for 500MHz CPU, the issue comes with additional effects like lighting but it is not so important.

STM32H747XIH6 touchGFX, project root directory, two seperated CM4 and CM7, touchGFX under CM7, when touchGFX designer create code， always to search .cproject under root directory, (.ioc is here, but no .cproject, only .project), under CM7 exist .cproject and .project! this cause touchGFX designer code generate fail!