STM32 MCUs TouchGFX and GUI

TouchGFX adds a redundant line ending to .cproject file when clicking generate code even if nothing has changed.This causes changes to show up in git and also makes merging and pull requests more complicated.In STM32CubeIDE the line ending is removed after making any change to the project (and optionally reverting the change). -<?fileVersion 4.0.0?><cproject storage_type_id="org.eclipse.cdt.core.XmlProjectDescriptionStorage"> +<?fileVersion 4.0.0?> +<cproject storage_type_id="org.eclipse.cdt.core.XmlProjectDescriptionStorage"> I'm using TouchGFX 4.23.2, but the problem was also present in older versions. Using STM32CubeIDE 1.15.1, but older version had the same effect.Please fix this.  

Hello ST Community Team,We are currently working on an STM32N6-based design using TouchGFX and would appreciate your guidance regarding the LTDC framebuffer address configuration.Setup details:Display resolution: 800 × 600Graphics framework: TouchGFXExternal memory device: eMMC – IS21ES08GA-JQLIThe eMMC is used as external memory in the systemWhile configuring TouchGFX and LTDC, we need to specify the framebuffer start address for the LTDC layer. Since the framebuffer is not located in interna

Hello,How do I enable 8MB external SPI Flash on the WBA65+RVA15MD using TouchGFX Designer?Thanks.  

Hello, I have a problem to display the screen on my board, it is always blank white screen. Below is a simple Screen:It shows as a blank white screen on my board, please find attached relevant files lest it is a hardware problem. Please advise. Best regards

Hello everyone,I’m working with the STM32N6570-DK and trying to bring up a TouchGFX project by following the official STM tutorial:https://www.youtube.com/watch?v=NFljjd_vQGAI generated the project with TouchGFX Designer and programmed the board using STM32CubeProgrammer exactly as shown in this one:FSBL flashed at address: 0x7000 0000Application flashed at address: 0x7010 0000The flashing process completes without any errors.However, when the board boots, the GUI is completely corrupted. The display only shows colored noise/static like in the video I attached.It seems like framebuffer data, LTDC configuration, cache handling, or memory mapping might be wrong… but everyth

I have successfully tested the board that is based on STM32H750B-DK Architecture using Touchgfx based code demo for STM32H750B-DK but now I have created a fresh stm32cubemx project with same files and settings and same ld as of the demo board but the Code is getting stucked at the static int32_t MT48LC4M32B2_Delay(uint32_t Delay){ uint32_t tickstart;tickstart = HAL_GetTick();while((HAL_GetTick() - tickstart) < Delay){}return MT48LC4M32B2_OK;}What could be the problem?

I hope to achieve the scrolling effect like the file browser of Windows. I attached a demo video.

Hi,Is underline of text supported by TGFX or will that be part of the ttf-files in Typographies?The goal is a text like this: "Press SETTINGS now." 

I have successfully run the USB HS Mass storage on a new project without the use of freertos and touchgfx , But when the touchgfx code  for STM32H750B-DK is modified to run the code I am getting hard faultsstatic uint8_t usb_done = 0; extern ApplicationTypeDef Appli_state; extern USBH_HandleTypeDef hUsbHostHS; extern FATFS USBHFatFS; extern char USBHPath[4]; void Debug_Print(char *str) { HAL_UART_Transmit(&huart4, (uint8_t*)str, strlen(str), 100); } static uint8_t file_written = 0; void StartDefaultTask(void *argument) { Debug_Print("Task Started\r\n"); for(;;) { USBH_Process(&hUsbHostHS); if (Appli_state == APPLICATION_READY && file_written == 0) { Debug_Print("USB Detected\r\n"); if (USBH_MSC_IsReady(&hUsbHostHS)) { Debug_Print("MSC Ready\r\n"); FRESULT res; FIL file; UINT bw; /* Mount USB */ Debug_Print("Mounting...\r\n"); res = f_mount(&USBHFatFS, USBHPath, 1);

I have created a UI in touchgfx designer, after I opened CubeMX and based .ioc file from touchgfx designer generate codes for stm32n6.Now I want to build these codes in Cube IDE but get this Error .   Errors occurred during the build.Errors running builder 'CDT Builder' on project 'STM32N6570-DK-FreeRTOS_Appli'.Cannot invoke "com.st.stm32cube.common.mx.registry.IIdeHelper.getRootProject(org.eclipse.core.resources.IProject)" because the return value of "com.st.stm32cube.common.mx.registry.MxRegistry.getIdeHelper()" is null  

// To regenerate crash, follow these steps // In simulator mode // 1. Rotate screen if (touchgfx::HAL::getInstance()->getDisplayOrientation() == touchgfx::ORIENTATION_PORTRAIT) { touchgfx::HAL::getInstance()->setDisplayOrientation(touchgfx::ORIENTATION_LANDSCAPE); } else { touchgfx::HAL::getInstance()->setDisplayOrientation(tou

Hello everyone,I’m working on a project with the STM32H750B-DK board using TouchGFX and FreeRTOS. I need serial output via the onboard ST‑LINK Virtual COM Port for debugging. According to the board documentation, the VCP is connected to USART3 on PB10 (TX) and PB11 (RX).The problem:In CubeMX, I select USART3, set mode to Asynchronous, and assign PB10/USART3_TX and PB11/USART3_RX. However, in the pin configuration table, these pins remain with "n/a" in the GPIO mode column, the "Modified" checkbox stays unchecked, and they are not configured as Alternate Function Push‑Pull. The generated code therefore never initializes the

I'm trying to use LCD16DebugPrinter to display debug text on a 480x480 RGB565 display running on STM32U5A9J-DK (circular display). I've set it up in TouchGFXHAL::initialize():static touchgfx::LCD16DebugPrinter debugPrinter; debugPrinter.setPosition(0, HAL::DISPLAY_HEIGHT - 20, HAL::DISPLAY_WIDTH, 20); debugPrinter.setColor(touchgfx::Color::getColorFromRGB(0, 0, 0)); debugPrinter.setScale(1); touchgfx::Application::setDebugPrinter(&debugPrinter);And in my view's handleTickEvent():static char debugStr[128]; snprintf(debugStr, sizeof(debugStr), "TICK TEST"); touchgfx::Application::setDebugString(debugStr);Nothing appears on screen. Things I've already ruled out:String buffer lifetime - using

This is a followup on this post https://community.st.com/t5/stm32-mcus-touchgfx-and-gui/compilation-error-macro-quot-bind-quot-requires-3-arguments-when/td-p/881690 . mƎALLEm provided very comprehensive answer for the issue. I was unable to post a reply hence this post. I've followed the solution to the letter using the guage touchgfx example. I got a blank white screen and this is the debug window: and here is main.c:                          &

I have a problem with disabling gfxmmu. I don't have a rounded display so that actually I do not need GFXMMU.I created a project by using Touchgfx Designer Templates (STM32H7S78 DK BPP). GFXMMU is activated in default. I would like to disable it. So, I disable it in cubemx then exclude instrumantation files. Then I updated TouchgfxHal.cpp and frame buffer adresses as 0x9000 0000 - 0x9020 0000.Then I could succesfully build the project. When I run it, it is working particularly but the frame/image is broken down. I am adding the image here!Could you explain me how to enable or disable gfxmmu properly from project?

Hi Team,I have an application running on touchgfx with STM32H750B-DK board, currently the display which comes along with this board is around 4 inch, but the requirements are 7 inch. Please help me to choose the display to integrate with the board. I'm currently in India.   Regards,Siva

Will this peripheral ever be documented in detail? i.e. registers, interrupts, etc.Or even a lightweight/low level library would be acceptable.We may choose STM32U5 for a product but not if we are forced to use TouchGFX for good performance. 

Hello everyone,I’m working on a project with an STM32H750B-DK board using TouchGFX and LWIP (Ethernet). After configuring LWIP in CubeMX and generating the code, I encountered a compilation error that took me a while to understand. I’d like to share the problem to help anyone who might run into the same issue.The ErrorIn file included from ../Application/User/gui/NetworkTask.cpp:13: ../../TouchGFX/gui/include/gui/model/ModelListener.hpp:13:23: error: macro "bind" requires 3 arguments, but only 1 given 13 | void bind(Model* m) | ^ In file included from ../Application/User/gui/NetworkTask.cpp:11: ../../Middlewares/Third_Party/LwIP/src/include/lwip/sockets.h:616: note: macro "bind" defined here 616 | #define bind(s,name,namelen) lwip_bind(s,name,namelen) | Similar errors appeared for Model.hpp.&nbs

Hello ST Team,I am working with the STM32N6570-DK board and trying to display the live camera feed on a TouchGFX application.I cannot find any ready-to-use example that integrates DCMIPP (Camera) and TouchGFX.Current Situation:TouchGFX Designer: I have created a UI with a transparent area in the center (Alpha = 0) to display the camera feed. (Please see the attached screenshot).Cube IDE Firmware:  I found the DCMIPP_ContinuousMode example and confirmed that it works fine independently. However, merging it into a TouchGFX project manually is quite difficult for me.

Hi ,I'm developing a product on an STM32N6 using TouchGFX. I need to display the image coming from the camera input on the product on the TouchGFX. During our tests, we were able to directly print the image from the DCMI input to the screen and it worked. However, we need an example that takes this image and displays it on the TouchGFX. The AI ​​example prepared for the N6 actually includes this type of work, but the code is not accessible. Could you please share the relevant project or the relevant part so I can integrate it into my project, or could you provide an example project for this?

I am trying to build a fresh project using STM32CUBEMX to run STM32H750B-DK -FMC-QSPI-LTDCProject is sucessfully build and all the respected files are generated, Now I copy the Linker file from the existing project(Touchgfx Sample project for STM32H750B-DK which is running fine) But after the modification I am getting ExtMem/bootloader.o is not compiled even if I have added the files in the respective directry. arm-none-eabi-gcc "../Core/Src/syscalls.c" -mcpu=cortex-m7 -std=gnu11 -g3 -DDEBUG -DUSE_PWR_LDO_SUPPLY -DUSE_HAL_DRIVER -DSTM32H750xx -c -I../Core/Inc -I../LIBJPEG/App -I../LIBJPEG/Target -I../TouchGFX/App -I../TouchGFX/target/generated -I../TouchGFX/target -I../Drivers/STM32H7xx_HAL_Driver/Inc -I../Drivers/STM32H7xx_HAL_Driver/Inc/Legacy -I../Utilities/JPEG -I../Middlewares/Third_Party/FreeRTOS/Source/include -I../Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2 -I../Middlewares/Third_Party/FreeRTOS/Source/port

..

On an STM32U5G7VJTX I'm using a custom board with an ILI9488 480x320 display in 16-bit mode on the FMC.I am using NemaGFX version 3.5.0 for the STM32U5x9 as I don't have STM32U5x7.Drawing lines for a test works fine as long as I skip the nema_cl_wait() function, which hangs forever.To give GPU2D time to finish the work, I replaced nema_cl_wait() with a short loop that takes enough time. But that's obviously not a good idea, as some tasks can take longer or shorter.On the STM32U5G9J-DK2 Discovery kit the same GPU2D stuff runs just fine!Is this because the GPU2D in the STM32U5G7VJTX isn't exactly the same as in the STM32U5G9ZJT6Q?I've experimented with the GPU initialization in nema_hal.c, but without solving this issue.Does anyone have any ideas?/** * @brief Draws a line * [in] x1 * [in] y1 *

Hello STM32 enthusiasts,While testing NemaGFX v1.3.0 for the STM32H7RS (M7), I discovered some differences compared to NemaGFX v3.5.0 for the STM32U5x9 (M33).1. nema_clear(color); Doesn't work, I had to come up with some solution: nema_matrix3x3_t m; NEMA_VG_PAINT_HANDLE paint; uint32_t color = nema_rgba(0xFF, 0xFF, 0x00, 0xFF); /* Fill the screen with a color */ #if defined(STM32H7S7xx) /* Use this on STM32H7RS */ paint = nema_vg_paint_create(); nema_vg_paint_clear(paint); nema_mat3x3_load_identity(m); nema_vg_set_fill_rule(NEMA_VG_FILL_NON_ZERO); nema_vg_paint_set_paint_color(paint, color); nema_vg_draw_rect(0, 0, DISPLAY_SIZE_W, DISPLAY_SIZE_H, m, paint); nema_vg_paint_destroy(paint); #else /* Does not work on STM32H7RS */ nema_clear(color); #endif2. nema_bind_src_tex / nema_blit Does not work with the NEMA_AL88 format, but luckily it does wor

 Does anyone have a component to display audio spectral graphs, specifically for the STM32N6570 Discovery?