STM32CubeMonitor (MCUs)

Hello A new release of STM32CubeMonitor-RF is available on st.com. Click on "Get latest" to download the version 2.18.0. What are the main changes in this version ? Alignment with STM32CubeWB firmware 1.23.0. Alignment with STM32CubeWBA firmware 1.7.0. Alignment with X-CUBE-WB05N_V2.0.0 Upgrade supported OpenThread version to 1.4.0 API 377 Support of Command Line Interface (CLI) : Add the possibility to send some commands or start scripts from command line Bug fix Changes details can be found in the  release note RN104 and User manual UM2288 Do not hesitate to create new posts if you have any question. The STM32CubeMonitor-RF team.

Dear all,haven´t yet found topic like this.I would like to...(need) make a windows executable file / application from a Cubemonitor flow.Any Idea if and how possible? Thanks and have a great day!

Hello. I can plot an array in STM32CubeIDE, STM32CubeMonitor and Keil uvision with the Time Graph or Logic analyzer in Keil using this function and viewing signal_sample: void plot_signal(uint32_t delay){ for(int i=0;i<_5HZ_SIGNAL_LEN;i++){ signal_sample=_5hz_signal[i]; for(int j=0;j<9000;j++){} // Delay } } The problem is that in all the software above, this gets plotted like a step plot, because the sample rate of the trace is so high it samples the constant value between the Writes to the signal_sample: &

Hello, I want to use STM32CubeMonitor to debug the code. The .elf is imported into CubeMonitor, and the connection is built. However, clicking on "Deploy", the follow error message shows: "TypeError: Cannot read properties of null (reading 'variablelist')". I check the .elf file, it really contains "null".  The .elf is generated in STM32CubeIDE. The code can be excuted in both debug and normal run mode without problem. But the .elf contains "null". How to solve this problem? Thanks for support!STM32User

Dear Expert,I could view an array-buffer thanks to "https://community.st.com/t5/stm32cubemonitor-mcus/how-to-watch-an-array-using-stm32cubemonitor/td-p/225086/page/2"Following flow is my test-flow blocks. Cube-array block was referenced from above link.When I tried to draw double graphs, I can see only one graph is updated.(following is captured image, where upper graph is updated but bottom graph is not updated.)

We were following the ULPMark™-CoreMark User Guide for getting the ulp mark score but the STM X-NUCLEO-LPM01A is always throwing up some error and the LD2(ErrorLED) turns on causing issues. Also if in the case it runs its always telling    “>! Validation failed, too little runtime: 0.014000000000000234” “>! Set iterations above 749999 for Energy run”. Even after using the same parameters its throwing the same error. Also at 1ms the connection is never achieved and fails.It would be great if you can guide us on this.

Hello ST Community,I'm using STM32CubeMonitor-Power (latest version) with an X-NUCLEO-LPM01A board (firmware v1.0.8), and I'm facing an issue in static current measurement mode.Problem Description:In standalone

Hi Is there a way to communicate with the STLNK-V3PWR to extract current consumption?  (the Acquisition & Replay output).  I would like to communicate with it via Python (or other language) to automate current consumption measurements? Thank you.Pete.

I want to store the stm32 cube monitor graph data or store the corresponding variable data in to xml sheet. How can I do that.

Hi, I'm using a fresh debian testing (12) and when i try to launch "SetupSTM32CubeMonitor-Power.jar", i get the error :Command line arguments: SEVERE: java.lang.ArrayIndexOutOfBoundsException: Index 70131 out of bounds for length 22674Debian is not in the supported operating system, but ubuntu should not be so far. I found on the forum, that the error occured on stm32cubemonitor on ubuntu recent version.Is there a patch/upgraded planned or anyway to make it run ?Could someone on ubuntu tell me if it work on it ? Thanks in advance,

Hello,I'm running ubuntu 24.04 and running STM32CubeMonUCPD with "jara -jar SetupSTM32CubeMonitor-UCPD.jar" fails with error  Command line arguments:SEVERE: java.lang.ArrayIndexOutOfBoundsException: Index 70131 out of bounds for length 22674This same thing happens for both version 1.4 and 1.3 of ucpd monitor. What are my next steps? Kind regards

Hello,I am experiencing an issue with STM32CubeMonitor on Windows 11 where some nodes, including acquisition out, are marked as "not found" and cannot be used.I have found similar reports from other users:https://community.st.com/t5/stm32cubemonitor-mcus/cubemonitor-acquitions-installing/td-p/660215https://community.st.com/t5/stm32cubemonitor-mcus/missing-acquisition-nodes-on-macos/td-p/644151I have tried the suggested solutions, such as running stlinkserver, but the issue persists. After starting stlinkserver, is there any additional setup required?Has anyone solved this issue using a different approach?

Hi,I am using a custom board based on STM32G4. I have successfully generated SINK code using cubemx and testing it using UCPDcube monitor. Explicit contract has done correctly but unable to select a source PDO. PFA, trace, and screenshot.  I appreciate any help you can provide.@FBL , Can you please check

Dear staffs,I'm going to use "STM32CubeMonitor" for several Nucleo boards, such as Nucleo144 of STM32H563.But, when I try to invoke, following dialog appears and does not proceed.Why ?Thank you 

I'm currently facing a frustrating problem with STM32Monitor. When I'm trying to parse data, the progress bar gets stuck at 10%. As a result, I'm unable to pull the project data list.Hardware environment: Windows 11

Hello,i use STM32WB05KZ for the bluetooth.With software can use to programme or to do some BLE test ?thanks

I downloaded Cube Power Monitor and am trying to use it to connect to the LPM01A. I have downloaded and installed the W8 version of the virtual com port driver. I can select the board in the drop down menu, but when I hit "Take Control", a dialog box pops up with the message `error pwr get`. When I hit okay, another pops up with the message `Get current range command failed` with another message below it `ERROR TIMEOUT`. Hitting ok

Mac refuses to start STM32CubeMonitor, it seems the app is neither code signed nor notarized.Happens with latest release 1.10.0

Hi  I have the cube monitor plugged in , and running the cube monitor power application. I had it working on my old computer (Windows 10) , but had to install the USB driver of ST web site. Since moving to my new computer, I cant find the driver again. Anyone point me to where it will be? My new computer is WIndows 10 too, and installing the cube monitor power application doesnt install the driver Many thanksScott

Hello A new 2.17.0 version of STM32CubeMonitor-RF is available on st.com. Click on "Get latest" to download the version 2.17.0. What are the main changes in this version ? Alignment with STM32CubeWB firmware 1.22.0 Alignment with STM32CubeWBA firmware 1.6.0 Alignment with STM32CubeWB0 firmware 1.2.0 Support of STM32WBA6x devices Bug fixes Changes details can be found in release note Do not hesitate to create new posts if you have any question. The STM32CubeMonitor-RF team.

On launch the STM32CubeMon-UCPD icon appears briefly in the dock and then disappears. The application does not launch. 

Hello A new version 1.10.0 of STM32CubeMonitor is available on st.com. You can download it on https://www.st.com/en/development-tools/stm32cubemonitor.html Click on "Get latest" to download the version 1.10.0. What are the changes in this version ? Node-RED® updated to version 4.0.7 GDB update to version 14.2, the new GDB is compatible with Ubuntu® 24.04.  Added the possibility to reset the log timing in the processing node, by sending a message with topic set to "clear". Added the support for snapshot mode with SEGGER J-Link probe Increased J-Link acquisition speed. Added a link to video tutorials

Hello,I would like to ask a question, if it is possible to access UCPD monitor via USB-UART bridge? I am following tutorial AN5418, with nucleo G0B1RE and SNK1M1 shield. Everything works fine when I use st-link, but when using uart bridge I dont see the board in board selection of UCPD and can log data only to UCPD trace...I have found out, that one can make it to work when one desolderes SB16 and SB15 from st-link on nucleo and connects LPUART to TX and RX of JP6. But is it also possible to make it w

Dear Sir,When I monitor the data, sometimes the value often accompanied by spikes, such as followed figure. In my case, I monitor 3 variables that update from ADC registers.

Hi,I would like to set the minimum and maximum values of a dashboard chart using custom values calculated with a processing node.I tried "single value" and "change" nodes, but without success.I attached my current flow...Thank youWalter