Automotive MCUs

Hi,      I need LIN driver library files for SPC584B70E5 microcontroller, please do the need full. Thanks.

The error will appear when I configurate the module of AdcGroupDefinition, but the port and the hardware channel are configuarted correctly and conform. How can i solve this problem from the picture?   category : Errorproject : Cho6M_Gpt_rtm2description: Invalid XPath-expression for Attribute "INVALID" of node "/AUTOSAR/TOP-LEVEL-PACKAGES/Adc/ELEMENTS/Adc/AdcConfigSet/AdcConfigSet_0/AdcHwUnit/AdcHwUnit_0/AdcGroup/AdcGroup_0/AdcGroupDefinition/__5": (1818) No value found for object ""detailed : Invalid XPath-expression for Attribute "INVALID" of node "<a href="datamodel://Cho6M_Gpt_rtm2?/AUTOSAR/TOP-LEVEL-PACKAGES/Adc/ELEMENTS/Adc/AdcConfigSet/AdcConfigSet_0/AdcHwUnit/AdcHwUnit_0/AdcGroup/AdcGroup_0/AdcGroupDefinition/__5">/AUTOSAR/TOP-LEVEL-PACKAGES/Adc/ELEMENTS/Adc/AdcConfigSet/AdcConfigSet_0/AdcHwUnit/AdcHwUnit_0/AdcGroup/AdcGroup_0/AdcGroupDefinition/__5</a>": (1818) No value found for object ""id : 1803resource

Dears,When debugging SPC58N's network function. When I add printf function using RUN IO components.It always crash. I want to ask how to debug freeRTOS TCPIP protocol? which method to check how to get statistics info and etc.Thanks for help.

Hello, As shown in figure, I import a samples project, compile failure hint "make: * * * [components/spc560pxx_platform_component_rla/lib/RSC/rules. Mk: 164: elf] Error 1 "How do I solve it,T  

I want to test the SPC5-FLASHER program.When installing the program, you must register the serial number.How can I get a serial number assigned?Should I send the saved information by e-mail after recording the serial number request information during the installation process?Please tell me in detail how to register the serial number.

HelloI working with spc560p and I send or receive with SPI very good and had no problem, but if I want to send or receive more than 4 bytes (32bits) in one message (one chip select), what should I do? I used this format for send and receive: spi_lld_start(&SPID2, &spi_config_Achip);spi_lld_exchange(&SPID2, 4, txbuf, rxbuf);spi_lld_stop(&SPID2); Is there any sample in spc5studio wizard?

We have bought SPC5-UDEBUG-TL license to be able to debug SPC58EE80 MCU.By description"Supports both SPC5-UDESTK standalone and the equivalent version embedded into Discovery board.Supports SPC5x MCUsSupports Multicore, eTPU and GTM debuggingIncludes FLASH programming capabilitySupport service provided through STMicroelectronics"Multicore and GTM debuging should work with this license but after registering license we got only one core debuging (unlimited by size of code). Multicore license we got after registration doesnt work and we did not got GTM license at all.Why is that?Michal Bedlivý

The mcu of SPC58 does not response the PORST reset. I knew one case that the mcu actives the reset escalation, but  MC_RGM.FRET.R and MC_RGM.DRET.R  have been set 0; I want know other possiable reason ?This problem confused me long time.  Thank you for give me some clue about this.

The chip I am using is SPC560P, please how can I do it to get the chip ID?

I am working on the development of SPC574K chip, but the debugger cannot connect with the chip successfully. When the chip is powered on, the crystal waveform is the first picture, which is normal. When I press the reset button or the connect button in the computer debugging software, the waveform of the crystal osc

Hi, I am trying out embedded virtualization with SR6X7, i have SR6X7 ZCU demo board with me. I am very new this this dev environment. could someone help me with embedded virtualization related docs.    Thanks in advance. Prabhu

Hello,I created a new project using default settings only to toggle an OUTPUT just to see the microcontroller performance.I monitored that outpup with an oscilloscope and I get only 4.17MHz.I am using a SPC58NH-DISP.Is that an expected output frequency or I am missing something?How much is the MIPS of SPC58NH microcontroller?PS.: it was used clock default settings.Best regards./* Inclusion of the main header files of all the imported components in the order specified in the application wizard. The file is generated automatically.*/ #include "components.h" /* * Application entry point. */ int main(void) { /* Initialization of all the imported components in the order specified in the application wizard. The function is generated automatically.*/ componentsInit(); /* Uncomment the below routine to Enable Interrupts. */ /* irqIsrEnable(); */ /* Application main loop.*/ for (

Hello, I want to do a boundary-scan test for a SIP module which uses ST Stellar Integration MCU SR6Gx series, how can I get its BSDL file?

I want to debug my SPC563M64 board in SPC5studio. What should I do? I will go there to obtain support files for boards like SPC58NG 1>C:\SPC5Studio-6.0\openocd\scripts\board\spc58NG_dis.cfg2>C:\SPC5Studio-6.0\openocd\scripts\target\spc58ng.cfg3>C:\SPC5Studio-6.0\openocd\scripts\target\spc58.cfg where can I get these files for  SPC563M64 board just like the above files for  SPC58NG board!!!

Is there a C program routine for the SPC560B series? I want to see SPI sending data and LIN sending data routines!

Can you tell me what these parameter settings mean? Is there any formula for calculating something? Does this 250000 represent 250KB/S! Is it SPI's SCK clock signal line? 

Hello Experts,I have AEK-MCU-SPC5LNK debugger and want to flash .hex/.out file directly into controller SPC582B.how can I do this. please share necessary step guide. I don't want to use any IDE like using debug mode to dump the code.   Waiting for reply!!   Thanks, Mohit

Hello! I would like to ask what each of the three modes in the picture below represents?Also, what does it mean if the GPIO parameter is set to PORT_1? I did not see that the GPIO bit 0 for this PORT_1 port is in use in the pin configuration editor! So I would like to ask if this parameter has been configured and used on this image?Also, what does this PCS Line mean by choosing PCS1?Is there a user manual for the parameter settings of DSPI for SPC582B! Because I want to know what the configuration parameters in the routine mean!

Dear Support team, I am Nitesh kumar from HL Mando Softtech India Pvt. Ltd.     We have ADAS based project in production stage. Boot sw was already developed by Other Team. Now we want to update the boot SW using Boot Updater. But unfortunately we are not able to erase and write the flash memory of spc560p50 microcontroller.   Therefore we seek your support on the points given below. You are requested to please guide us on the below mentioned point.    We have the project workspace of MPC5604P microcontroller so can we use the same project workspace for spc560p50 microcontroller to erase and write the flash memory? Can you please share the sample code to erase and write the flash memory of spc560p50 microcontroller?   If you need more information from me please let me know.

Hi,I'm using TMS570 with SPC5STUDIO environment.My toolchain generates out.elf and out.hex but I would like to have a byte hex stream (without address and other information) directly do use as download byanother microcontroller that lead TMS570.I have to write a source code to analyze and parse the .hex orit already exsist that format?ThanksFabio

Posted on August 07, 2014 at 12:03Hello community, i try to use the PinMap wizard in SPC5 Studio 3 and i receive the meassage ''Device specific model ''SPC563M64L7'' not supported!'' and it seems that there is no support for any model cause i try it with different cpu's. I use the SPC56M- Discovery board and i'm wondering also that this board is not available in the SPC5Studio Application Wizard. Any ideas? Thanks for your help! - Marc

Can be deleted.Noone gonne help in that weirdo forum here anyways.

Hi Team, we are using SPC56EC70B3 Microcontroller, We are trying to give a digital signal to the corresponding pins PA[1], PA[2], PC[8], and PC[9]. All the pins are configured in the same way on the software side, we have also enabled the diagnostics pins for the above corresponding pins; we can't able capture any frequency from the pin PC [8]. Rest all the pins are working as expected. Then We identified a discrepancy in the malfunctioning pin PC[8] within the UCIN of the CSR in the eMIOS UC Status Register. Specifically, for channel 3, it consistently remains in a high state (1). This issue is critical to our project, and we urgently request your assistance in resolving it. 

Hello Community Experts, provide the causes for SBC resets the MCU continuouslyWe injected the E2E ECC into SRAM and respective FCCU channels were configured for EOUT enable and SBC configured to RSTB for Fail safe.We have run into a regression on the MCU that we believe is related to the changes for the ECE reset enablement.  The issue we are seeing is the MCU will continuously reset when jumping to the bootloader. The reset appears to be coming from the SBC 

Hello All, I am currently working on implementing a bootloader via CAN on the SPC582B60E1 microcontroller (i.e., Update the firmware file using CAN). To achieve this, I have been referring to the "Firmware Updater Component" PDF document.and also referring to 'SPC582Bxx_RLA Bootloader Test Application for Discovery' sample application code.Following the instructions outlined in the document, I have set up the communication mode, baud rate, and address for the program to be loaded. During the upload process, I have been adhering to the procedure of sending the password first, followed by the binary file size of the program, and then the bin file itself.However, despite successfully sending the password and binary size frames, I am encountering an error when attempting to send the binary program. Specifically, the error indicator LED turns on after sending the binary size frame, and subsequently, the binary program fail