STM32CubeProgrammer (MCUs)

Hi,our c 13:26:59 : STM32CubeProgrammer API v2.14.0 | Windows-64Bits 13:27:37:380 : UR connection mode is defined with the HWrst reset mode 13:27:38:416 : Device Descriptor: 13:27:38:416 : |_bLength : 0x12 13:27:38:417 : |_bDescriptorType : 0x01 13:27:38:417 : |_bcdUSB : 0x0100 13:27:38:417 : |_bDeviceClass : 0x00 13:27:38:417 : |_bDeviceSubClass : 0x00 13:27:38:418 : |_bDeviceProtocol : 0x00 13:27:38:418 : |_bMaxPacketSize : 0x40 13:27:38:418 : |_idVendor : 0x0483 13:27:38:418 : |_idProduct : 0xdf11 13:27:38:419 : |_bcdDevice : 0x2200 13:27:38:419 : |_iManufacturer : 0x01 13:27:38:419 : |_iProduct : 0x02 13:27:38:419 : |_iSerialNumber : 0x03 13:27:38:420 : |_bNumConfigurations : 0x01 13:27:38:420 : Configuration Descriptor: 13:27:38:420 : |_bLength : 0x09 13:27:38:421 : |_bDescriptorType : 0x02 13:27:38:421 : |_wTotalLength : 0x36 13:27:38:421 : |_bNumInterfaces : 0x01 13:27:38:421 : |_bConfi

Hi,I've just downloaded the STM32CubeProgrammer software in order to build a C++/QT project with it.As I was adding the CubeProgrammer_API.dll into my project, i found that i needed some QT5 dlls dependencies such as : Qt5Core.dll Qt5Script.dll Qt5SerialPort.dll Qt5Xml.dllthe problem is that i'm using QT6 in my project ! is there by any chance a version that dont need QT or at least QT6 ?is there any source code that i could compile on my side in order to update those dependencies ?Thank you in advance for all the support you can provideRegardsSofiane

Hello, STM32cubeprogrammer fails to install, can you assist?M1 Macbook Pro (Ventura 13.4.1)Java Version = 1.8.0_381STM32CubeProgrammer = 2.14.0 

I updated my old STM32CubeProgrammer to 2.14. Now it  takes a very long time to start... Much more than the time to program the MCU! What is he doing during this time? No doubt marketing exchanges with ST servers. The primary use of this type of tool is to work with the MCU, not to wait for it to finish conversing with ST. Could you go back to a more convenient start time? Thanks.

Hello forum,we are facing a very strange issue with the STLINK-V3MINIE debugger.Controller: STM32G0B1CE seriesSTMprogrammer version: 2.14.0Debugger:  STLINK-V3MINIEwe are trying to connect the device(controller) with the stm32programmer application using STLINK-V3MINIE debugger but every time it is showing the error message as shown below.Error: No STM32 target found! if your product embeds Debug Authentication, please perform a discovery using Debug Authentication. 

Hi, are there any information's or app-notes available how to use this programmer over CAN bus. I cant find any information which hardware is supported or how make the can hardware on my laptop visible to the programmer. Thanks for your support!

Hello,I have implemented a little project with a nucleo board with STM32G474RE MPU. The purpose is to manage the firmware upgrade, written in the user flash, from a PC connected via USB interface. The MPU, when boots up, start in the DFU modality since the boot0 pin is high (nSWBOOT pin is also high the first time) and so the program starts from system memory. The PC connects with the DFU, parse an hex file, transforms it  into a bin file and writes the flash directly using the API: sendOprtionBytesCommand() and writeMemory(). After doing that the PC switch the MPU to the user flash calling the API: execute(0x08000000).MPU at this point should modify the option bytes so that all following reset will start from user flash. And that is achieved by setting nSWBOOT0 to 0 and nBOOT0 to 1. There are HAL specific API that can be called to perform  that task. But the problem is that, when the program in user flash starts, there are already

Hi,I have another problem with the board "STM32F769I-DISCO, MB1225 B-02, A201800875".I wanted to restore the original firmware of the board.Download from ST site the image "10_2020\32F769IDISCOVERY_demo\Binary\STM32769I-DISCO_DEMO_V1.0.0_FULL.hex". Loaded it according to the "32F769IDISCOVERY_demo\readme.txt" file. I used two applications for loading:1)STM32 ST-LINK Utility 4.62)STM32CubeProgrammer 2.4.0with the same result, load the main picture with ST logo and stops. Nothing else. I think the reason is the wrong firmware revision. Before deleting the original " FW" I checked System Info and their FirmWare revision is 1.2, but I didn't find anywhere on ST site firmware such revision.But when I do the same on the previous board " Board: STM32F769I-DISCO, MB1225 B-02, A192400285 Screen : MB1166 A-02, A192400688"with the "10_2020\32F769IDISCOVERY_demo\Binary\STM32769I-D

Hi,I just downloaded and installed the STM32CubeProgrammer version 2.14 for linux.The installation went without any issues. However, when I execute STM32CubeProgrammer an exception is immediately raised (see below). I tried to run it as root, but this did not help (same error).I am connected via a terminal and an (working) X connection. The installer is used via the same terminal and connection.I do not have any other java installation (other than the java which is installed by the STM32CubeProgrammer installer).I have googled for this error, but I cannot find any solution for this.Any help is much appreciated. :/usr/local/STMicroelectronics/STM32Cube/STM32CubeProgrammer/bin$ ./STM32CubeProgrammerException in thread "main" java.lang.reflect.InvocationTargetExceptionat sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:6

Hai ST, I am working "STM32f103c8t6", while connecting st link debugger  , shows like   "UR connection mode is defined with the HWrst reset mode" ... 

Hello,I have seen that in the new version of STM32CubeProgrammer (v 2.14.0) there's a new API that can be used to program a flash using DFU bootloader (API which I didn't see in my previous STM32CubeProgrammer).In addition to the writeMemory() now we have the editSector() function. But the description (reported in the .chm file) is quite the same. Anyone knows what's the difference between these two functions? Thanks all

If I use CubeProgrammer to connect the internal boot loader of STM32H750XBH6 via USB (pull Boot-0 high), can I program the external SPI Flash through CubeProgrammer? I know it's possible to do this using ST-Link (ps. by stldr) directly, but I can't do it using USB by similiar way. 

Hi Team,When I tried to flash the code to stm32f411ceu6 using the stlinkv2, I was getting the error "Error in initializing ST-LINK device.Reason: No device found on target.This error was corrected using the STM32 ST-Link UTILITY. When the USB cable is first plugged in, hold down the reset button, and immediately select Target->Erase Chip upon release.  Once the chip is erased, the bootloader will be able to utilize the USB connection correctly and you will be able to use the USB port to program.After this, I did a Mass Erase (Full chip erase)in the  STM32CubeProgrammer.  STLINK got connected in  STM32CubeProgrammer. But while flashing the code to the STM32 MCU, We are getting the error:"Target not responding, retrying". Kindly provide a solution. Waiting for replyThanks and RegardsAnitta Darwin

WRP cho phép cấu hình các vùng bộ nhớ Flash không thể ghi vào sau khi chúng đã bị khóa. Lõi xử lý chính (Cortex-M4) chỉ có quyền truy cập và thực thi mã nguồn trong các vùng bộ nhớ được bảo vệ bởi WRP??? Điều này đúng hay sai?

Hi, Spoiler (Highlight to read)I would like to get help from you on a problem that I spent a lot of time on but could not solve. I am trying to do the software update operations of a card of our own design with an STM32WB55 MCU, using STM32_Programmer_CLI.I wrote a simple C# GUI which calls these commands step by step and waits for STM32_Programmer_CLI app to exit.Clear nBoot0 and SwBoot0"STM32CubeProgrammer CLI (Standalone)\Bin\STM32_Programmer_CLI.exe" -c port=usb sn=207834575352 -ob nBoot0=0x00 nSWBOOT0=0x00"Check if FUS is running"STM32CubeProgrammer CLI (Standalone)\Bin\STM32_Programmer_CLI.exe" -c port=usb sn=207834575352 -fusgetstate

..

Hi Everybody,I am trying to test out the boot-loader of the stm32l412 as a part of development for a product my company is making. For reasons unknown to me, the STM32cubeprogrammer (v2.10.0) can only sometimes program my MCU . I made a batch script that looks something like the following, and I run it in power-shell.~~~~~~~~~~~~~~~ script startecho offif NOT .%1 == . goto okecho Error: specify Debug or Releasegoto doneif NOT .%2 == . goto okecho Error: need com port as argumentgoto done:okC:\Users\mcocke\Desktop\WorkFiles\ProjectFiles\SomeFolder\STM32CubeProgrammer\bin\STM32_Programmer_CLI.exe -c port=%2 dtr=low rts=low br=115200 P=EVEN db=8 sb=1 -w C:\Users\mcocke\Desktop\WorkFiles\GithubRepos\OtherFolder\STM32L412CBU6\%1\STM32L412CBU6.elf 0x800000000 -V:done~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ script endMy issue is that sometimes (I think 50% of the time on a good day) the programmin

STM32CubeProgrammer v2.14.0 release information New features:• Updated the support for the entire STM32H5 series: – Debug authentication with password or certificate – Authentication key provisioning – Key generation – Firmware encryption and signing – Certificate generation – SFI support, secure manager install, and module install/update• Added support for microcontrollers in the STM32L5 series and STM32WL series: – SFI integrity check• Updated support for the STM32U5 series: – SFI support for the STM32U535/545, STM32U575/585, STM32U595/5A5, and STM32U599/5A9 product lines• Added support for the STM32U5Fxxx and STM32U5Gxxx microcontrollers: – SFI support: user interface and command-line interface – SFIx support:   ◦ Via debug: user

Hello,I am using STM32_Programmer_CLI extensively from scripts (bash, python, ...) to test firmwares automatically.One really annoying thing is the fact that the tool persists to output colors even when its stdout is not an interactive tty, this make it annoying to build complex regex to extract informations.Would it be possible to add a CLI option to suppress colors from stdout/stderr, or even better detect automatically if the output is connected to an interactive session and if not disable the coloration of the output.Thanks for your support.Nicolas.

Hi, I had tried writting my own Makefile to build the project but failed. Then I installed Qt5 unwder Ubuntu and followed your doxygen documentation except I didn't use mingw but the original g++, and it failed too. Although I add all the files you mentioned in the doc, it still has the unkown reference error.Now I have no idea about the build environment and link configuration under linux, so I really need some help. Best regards

I am using the Riverdi RVT70HSSNWCA0 display with the STM32H757XIH6 (2MB Flash, 1MB RAM) microcontroller on board. I have generated the touchGFX code and ran the target. It has properly flashed the screen and the image and buttons look good. I have attached the photo of this.I now need to add functionality to this code. I open the code in CubeIDE and compile with no build error (I have not changed any code from touchGFX's output yet). I simply want to flash the screen with the generated binary file (Flash.bin). When I flash the stm32 with this code, it is extremely distorted and does not work properly. I have attached the picture of what it looks like. Please help me:) 

Hello,I am using the STM32CubeProgrammer with my board in DFU mode (over USB).It programs fine, but my application does not run after programming even though I checking the "Run after programming" option. and by programs fine, I mean if I power fail the board, the code runs.Any suggestions on troubleshooting this?Thanks,Mark

Hi,I have erased the program in the chip by pressing erase program in the STM32Cub programmer, now the board is not working , Can you please support on this issue?   

hi frnds..i want to know how to measure ac current in bldc motor using shunt resistance for stm32f103c8t6.please reply ...

Hi,I am using stm32mp157c processor with kernel version 5.10.10 over custom carrier board.I interfaced LVDS display via sn65dsi83 which is MIPI-DSI to LVDS converter and its working fine.Now i am integrating the interrupt generated by my sn65dsi83 ( which is usually generated when there is any problem in DSI lines ). Refer interrupt.patch how i integrated my interrupt.This patch works fine and when interrupt is generated my irq_thread is called. In which i wrote a simple print function.I generate interrrupt using devmem tool. I use this tool to change my DSI register settings. This force my display to go off and black screen appears. when this happens and interrupt is generated and irq_thread is called.Now want my interrupt handler to reinitialize my MIPI-DSI registers so that my display will be back in action.I tried using drm_mipi_dsi_soft_reset() function. but i think this funtion don't reinitialize registers.is ther