MEMS (sensors)

In ASM330LHB datasheet, gyro and accelerometer self test to be executed only when device is in static condition. But in field operating environment, device may goes into high dynamic condition during self test active, thenis ASM330 device gets damaged ?  OR device will be ok but only self test results will be failed?Thanks is advance,Pavani.

Dear Sirs,I would ask how it is connected ISM330BX with STEVAL-MKI245KA in the webinar. In fact STEVAL-MKI245KA has inside different sensors and I don't see the connector to plug STEVAL-MKI245KA.Moreover in en.FP-AI-MONITOR2_V1.0.0_RC8 need to be installed in CubeMX?The en.FP-AI-MONITOR2_V1.0.0_RC8 use one of INT1 and INT2 or both of ISM330BX? Thanks

Dear,I'm testing the lsm6ds3tr-c free fall function, but it's hard to tuning the threshold, i attach the current registor settings, I want to dectect the 1m free fall, can you give some guide? thanks a lot.

Hi, I’m working with the IKS4A1 Nucleo expansion board and F401RE. I need to generate a PWM signal on INT pin 2. The documentation I found focuses on connecting the IKS4A1 with MEMS Studio, and I couldn’t find guidance on configuring PWM signals in MEMS Studio.Is it possible to configure the PWM signal in MEMS Studio, or do I have to use CubeIDE instead? Any guidance or resources would be greatly appreciated!

I am trying to do USB sensor data streaming Real Time Plot by conecting  my steval mkboxpro with hsdatalog_GUI.py but it keeps saying "Device Template Model Loading". Anyone can help?Thanks 

Hello,I am programming my ISPU code that work on interrupts INT1 and INT2 in STM32CubeIDE and testing it in STEVAL-MIK109V3 with adapter board MKI229A (LSM6DSO16IS) and showing my output value in MEMS Studio.I configured the conf.txt linking the interrupts NT1 to function "algo_00" and INT2 to function "algo_01".conf.txt:     acc_odr 104     acc_fs 2     acc_mode high_performance     gyr_odr 104     gyr_fs 500     gyr_mode high_performance     ispu_irq_rate 104     ispu_int1 enable     ispu_int2 enable     ispu_latch disable     algo 0 enable     algo 1 enable     algo_int1 0 enable     algo_int2 1 enable After building and uploading

I have been trying to get a connection to my sensortile kit using the serial  connection. I only get "Board not identified". I have tried loading the DatalogExtended.bin file to try get the board to be recognized but this didn't help. I also tried making a small "application" with the Algobuilder in Mems Studio but this seems pointless as there is no connection. Is there a tutorial or app note that could explain how to get the software to detect the kit? 

Hello, I am using the LSM6DSOX sensor and reading data from the FIFO, following these examples on GitHub (https://github.com/STMicroelectronics/STMems_Standard_C_drivers/blob/master/lsm6dsox_STdC/examples/lsm6dsox_fifo.c). I've set the same frequency for both the accelerometer and gyroscope, but when I read the data from the FIFO in continuous mode, the samples are not aligned. For example, I receive the first two accelerometer samples followed by one gyroscope sample, then three accelerometer samples, two gyroscope samples, and so on.Since the frequencies are the same, shouldn't I receive one gyroscope sample and one accelerometer sample consecutively in a 1:1 ratio? Is this behavior normal? Or is it necessary to adjust the accelerometer's configuration in some way to ensure that the samples are al

Hello I am working with an ST magnetometer sensor to detect movement along the X-axis. I have a custom board featuring an L4 microcontroller, which enters STOP MODE 2 until an interrupt is triggered. I use the following function to initialize the sensor for this mode, after which the device goes to sleep. When the magnetic data exceeds a specified threshold, the magnetometer generates an interrupt and the device wakes up. However, I am facing a challenge regarding maintaining the device's proper functionality when exposed to temperature variations. The interrupt generation is based on raw magnetic data returned by the function lis2mdl_magnetic_raw_get(). I am aware that the temperature fluctuations, such as reaching 50 C, can distort the magnetic readings, potentially causing inaccuracies. The magnetometer will require calibration, but my question is how to apply the calibrated values in the system?   Currently, my approach is to keep the device

I want to collect data wirelessly using the SensorTilebox.PRO and an STEVAL-MKI240KA (LSM6DSV32X) connected via the DIL24 socket. When I flash the DATALOG2_Release binary, I can see the onboard sensors using the ST BLE Sensor app, but not the external IMU. When I flash the MEMS Studio datalog extended firmware, I can log data from the external IMU but the device must be connected to a computer using a USB cable. Are there any pre-existing solutions allowing for datalogging (either through BLE connection or automatically on startup) with data from the external IMU, or does this functionality require directly modifying and flashing custom firmware?

Hi, I have been working with iis3dwb since 2020 and a week ago me and my colleague found something that looks like a design mistake from ST side, we found something like sample losses during FIFO buffering I am not sure but further I will try to provide as much info as possible to be understood. There will be a lot of details because the question isn’t easy.Prehistory:Me and my team designed a vibration sensor(further VTS) based on iis3dwb mems accelerometer (spoiler: it’s great, but…) and we are happy about it. Until recently we thought everything is ok and data reading is working as it should be, I did a lot of tests to see if we have some sample losses, I tested it on 8192 samples num for each axis due to internal uC memory limitations (and this amount was enough to calculate FFT and then acc RMS, velocity RMS… with required frequency dimension and accuracy). But this was the first step in production of VTS, then we installed 8MB RAM to store 1minute,

Hello!  First I would like to state my issue:  1. My software cannot connect to the LSM6DSO IMU sensor.   A little background on my project is that I am trying to use the IMU sensor to provide accelerometer readings in x, y, and z directions. I purchased a breakout board from Sparkfun that uses the LSM6DSO to test the sensor first with my Arduino-compatible controller via SPI communication. This proved that it works.  We then created our own design and referenced the way Sparkfun wired the LSM6DSO. Now when I run the program on the new board, the sensor doesn't work.  I looked into the library that Sparkfun uses for programming in Arduino and I see that it canno

Hi,We are working with the LPS22DF pressure sensor to be used in our device adapting a 3.3V system and have encountered issues related to the interaction between VDD_IO, VDD, and the I²C bus. When VDD_IO and VDD are connected to the same 3.3V supply:The I²C bus behaves as expected. (No issues here)However, when we disconnect VDD_IO and VDD, while I2C is active to be used for other sensors to communicate, the sensor seems to backfeed through VDD_IO's internal pull-up to VDD, interfering with the I²C bus (e.g., pulling lines to ~1.5–1.6V). (this is our theory at least)When VDD_IO is powered but VDD is not:I²C communication is disrupted.The sensor seems to partially power itself thro

Hi, I am using MotionFX with BlueCoin, for a solution that can detect vertical movement within 2 meter range with high precision.  I took the ALLMEMS2 example when I logged linear acceleration and gravity, it showed some unprecise values likelinear acceleration around 0.2 when the device wasn't moving. When I increased the full scale factor for ACC to 16.0f and Gyro to 2000dps, the linear acceleration value improved to the range of 0.05-0.1, which is still not as expected. Gravity value is strangely too high and stable 9.99, shouldn't it be closer to 9.81 max in the stale state?  NFO:__main__:Linear Acc -> x: 0.0290, y: -0.0090, z: 0.0190 INFO:__main__:Gravity -> x: 0.0590, y: 0.0310, z: 9.9990 INFO:__main__:Linear Acc -> x: 0.0090, y: -0.0180, z: 0.0490 INFO:__main__:Gravity -> x: 0.0580, y: 0.0300, z: 9.9990 INFO:__main__:Linear Acc -> x: -0.0110

Hello community,I have an application where I want to implement STHS34PF80 for detecting people PRESENCE and MOTION with a range of 3 to 4 meters. In the Datasheet it is stated that it is possible without using extra lenses. Although, I am struggling to find the best config to have a good recognition with more than 1,5m.- What would be the step-by-step to make the sensor run in 4 meters range?- Could someone give me an example config for THRESHOLD, HYSTERESIS, LPF, ODR and AVG?

FIFO_CTRL4 is 00A1 in hex , 10100001 in binary FIFO_CTRL3 is 00AA in hex , 10101010 in binary fifo_status1 is 00000000 fifo_status2 is 00100010 FIFO DATA OUT TAG IS 00100001   I have already set LSM6DSO like this but no data is inside the FIFO Must I open and close embedded function?  I saw someone 's reply in the community  riteRegister ( LSM6DSOX_FUNC_CFG_ACCESS, 0x80 ); //Open Embedded Functions WriteRegisterBit( LSM6DSOX_EMB_FUNC_EN_A, 3, true ); //Enable Pedometer sensor in Adv Func WriteRegister ( LSM6DSOX_EMB_FUNC_EN_B, 0x10); //Enable false positive rejection WriteRegisterBit( LSM6DSOX_EMB_FUNC_FIFO_CFG, 6, true ); //Enable Step Counter Batching WriteRegister ( LSM6DSOX_FUNC_CFG_ACCESS, 0x00); //Close Embedded Functions  

Hello,I am using MotionFX on STM32BlueCoin device. I tested values of linear_acceleration and gravity from MotionFX library, and I have very strange bias on produced values, although I try to feed perfect hardcoded data to the library.For example I always send MotionFX 6X input data as following, Accelerometer x=0, y=0,z=-9.81, Gyro x=y=z=0In return, I have strange values on the gravity axis. INFO:__main__:Gravity -> x: 0.0000, y: 0.0000, z: -10.0000 INFO:__main__:Linear Acc -> x: 0.0000, y: 0.0000, z: -0.1890 INFO:__main__:Gravity -> x: 0.0000, y: 0.0000, z: -10.0000 INFO:__main__:Linear Acc -> x: 0.0000, y: 0.0000, z: -0.1890 INFO:__main__:Gravity -> x: 0.0000, y: 0.0000, z: -10.0000 INFO:__main__:Linear Acc -> x: 0.0000, y: 0.0000, z: -0.1890  Why is gravity Z always 10? Shouldn't it be 9.81 in perfect condition? Why linear_acceleration have this s

Hi,I am developing a product that can be installed in either a horizontal or vertical orientation and uses the LIS3MDL as the source for a compass..The PCB is common so the LIS3MDL will be in one of 2 orientations.In a horizontal position everything is fine and I get the readings expected.In vertical orientation it is not working.My assumption was that the axes X,Y,Z were just names and that the data from each axis was relevant to that axis and that the data obtained would relate to the plane that axis was on.It seems this is incorrect. I have run a test and see that the range of values (max-min) on each axis is very different, particularly on the Z axis.Moving the sensor through 360 degrees on each axis I am getting X -59 to 25, Y -36 to 46, Z -86 to 0I assumed I would get the same min to max for each axis.So can the sensor be used in a vertical orientation? I need the Z axis facing forward (to replace

Hi,  I want to detect a shock  with the H3LIS331DL and its interrupt on threshold level. I used it in normal mode and an ODR of 1000Hz. The shock in my testbanch is : I want to know what is the minimum of time when the duration is setup to 0 with my ODR to set interrupt signal.What is the answer of the sensor when the shock is an high frequency one...There is few information about the bandwidth of the sensor or about its transfer function in its datasheet or application note.Thanks for your help   

Hello, I'm using the LIS2DW12 on my own board.Consumption seems a little high to me. In the datasheet I found a value around 5.5µA and I obtained rather 45µA.The configuration is as follows:- ODR 50Hz- FIFO in continious mode with INT1 enabled- Full-scale 4g- 14 bits resolution in LP2.I did not find any information regarding consumption in FIFO mode. Can you give me some information?Thanks

Hello,I am using STEVAL-STWINKT1B development board and I can write and read sd card using setting to SD 4 bits Wide Bus and FATFS.If I add on STM32CUBEMX as middleware FREERTOS I can't read the SD in fact I get back FR_NOT_READY when I execute the f_open method.How can I solve this problem?

Hi, I'm trying to decipher the inner workings of the fsm configuration on this sensor. While the an5904 application note features an example of configuration on page 42, things take a turn after the 21st step. The following step selects page 2, and I can't find a description of the page contents anywhere. The only available description of the embedded advanced features pages is for page 0 in the data sheet. 

Hello,  How many mechanical shock support the LSM303AH please ? and if uou have others reference of inclinometers thanks to give me informations. Thank you

Dear, Could you tell me if FS signal have internally pull up or pull down?   Regards

Hi Everyone,I'm using STM32L4 with LSM6DSM on IAR IDE and using motion AC library to calibrate the accelerometer data. Code flow is like in first position when it has got the 500 samples for one position then it will wait till you rotate the position and when it is in next position again it will take sample for that position. The problem is, If I kept the device for longer time in one position only then lets say 2 min then sensors doesn't get calibrate, not able to understand what can be the reason.Because I'm not able to find out is there any timeout or any buffer overflow is happening.