MEMS (sensors)

Does anybody know where do I get the .a library for LSM303AGR on ambiq apollo4blue plus platform which contains following feature.Acc Data + Mag Data -> AzimuthMag Data Calibrationnote:I am currently using this two library, but it doesnt work well and I have been tring to find the referrence about this two lib but I can not find any as well. 

We have a STEVAL-MKI224V1 kit, which should be equipped with a LPS22DF. I have tried to use the static (I2C) address of the sensor, and after much time, I discovered it is (depending on the state of SDO) 0x5C/0x5D, and not 0x6B/0x6A, as stated in the datasheet.Strangely (or not) 0x5C/0x5D is the static address of the LPS22HH, but according to the GETPID command, I do have a LPS22DF.Thank you.

Hello,We have implemented the LIS3DH with a nRF52832 in I2C mode on our board, and are using the accelerometer to detect motion and vibration events. The LIS3DH internal high-pass filter and threshold detection are used to generate the INT1 interrupt.Our issue is as follows. We are observing an excess current draw of ~40uA in this state. Our evaluation has found the excess current to be associated with setting the INT1_CFG register value for interrupt generation. Attached are two charts showing 10 minute periods of idle current measurements of the whole PCBA, one with firmware built to set INT1_CFG=0x2A, the other with firmware built to set INT1_CFG=0x00, and otherwise the exact same code. The spikes in current can be ignored, those are BLE advertisement bursts. In neither case was the interrupt actually triggered.LIS3DH registers are set as below, other than the changes noted above. Register writes occur in the order indicated. I have also attached a screenshot

Hi there!I'm having issues with my LSM6DS3TR device FIFO. I am trying to read and process all values stored in the FIFO by the accelerometer every interval using I2C. I am doing this by:1) Retrieving number of unread messages in FIFO at addresses 3Ah and 3Bh.2) For every unread message:2.1) Reading the pattern in address 3Ch and 3Dh.2.2) Reading the value of the FIFO in addresses 3Eh and 3Fh.2.3) Processing and storing value retrieved from value as x, y or z axis. I assume the pattern will tell me which axis the FIFO value relates to? I am only using the accelerometer, so I assume pattern = 0 is x axis, 1 is y axis and 2 is z axis? However, the pattern seems to be corrupted when I leave the program running long enough and will no longer align with the axis; for example- sometimes it will sh

STHS34PF80 code needed to access SEL_ABS bit in ALGO_CONFIG embedded register Address: 28H using Arduino NanoI would like to know how to generate the code to set SEL_ABS bit in ALGO_CONFIG embedded register using Arduino Nano Board as the micro-controller.

Hello everyone,My goal is to record audio from one MP34DT05-A microphone via SAI PROTOCOL in an STM32F446 Nucleo Board. In resume, I receive data from microphone via DMA, then I make the transformation via PDM2PCM Library and write the buffer into an SD CARD via SDIO.I'm using STM32Cube IDE and I can see that the two buffers (input SAI data and output PDM2PCM data) are always being updated with values. Also, I confirmed that all the values are written into the SD with no missing values.I tried to replicate the code from "Microphone_Streaming" Stm32 examples (also made in this video: https://www.youtube.com/watch?v=BjTj1XXpjBU. But the result is always looking like this graph below. It seems like the microphone never respond to any higher sound... 

Hello all.I would like to ask how to calculate dB from a data recorded by a MEMS microphone.I currently use the MP34DT04 on the SensorTile Kit. I checked the SensorTile can record sound with the microphone, and store a wav data file in MicroSD.In the .wav file, there are chunk of data and, of course, there are sound level data. Then, I would like to calculate dB data from the sound level data. How can I calculate?If the sound level data is 16 bit, the data would be in between -32768 and 32768. Is the digit can be mapped to full scale sensitivity? The sensitivitiy means the parameter in the datasheet. In the case of the MP34DT04, the sensitivity is in the range of -26dB to 120 dB.I also wonder what the description in the page 6 of the datasheet means. It says "Duty cycle: min = 40% max = 60%". Is it related to the dB calculation?Please take care yourself first, and looking forward to the answers. 

I BOUGHT STEVAL- MKBOX PRO AND AM THINKING OF USING IT.I have a wireless function, but please tell me the status of technical conformity approval for use in Japan.There was no conformity mark on the package.

Hello,I'm designing a custom board with a LIS2DW12 accelerometer for motion detection. I want to use INT1 to send a signal to the MCU when it detects movement, which should wake up the whole system. The accel supports both i2c & SPI communication but I intend to use SPI. I would like to verify how I plan to make my connection between the accelerometer and MCU. Please refer to the images below.

1- Is there a permanent memory in LSM6DSOX for machine learning? In other words, does the ".ucf" file that we load in case of power off or reset become permanent?2- Can we load the ".ucf" file without using "STEVAL-MKI109V3"?3- Can we load the ".ucf" file using I2C communication? Thank You.    

Hi,I am working on a custom ISPU code for LSM6DSO16IS and I want to generate interrupts on INT1 and INT2. I checked all the examples in x-cube-ispu/Ispu/ism330is_lsm6dso16is at main · STMicroelectronics/x-cube-ispu generates an interrupt only on INT1.Is it possible to generate interrupts on INT1 and INT2 at the same time? Thanks a lot :)Chen

私はB-L475E-IOT01A2(開発ボード)が手元にあります。B-L475E-IOT01A2に含まれている以下のセンサーを使ってデータを取得をしたいと思っています。相対湿度と温度の静電容量式デジタルセンサー (HTS221)高性能3軸磁力計（LIS3MDL）3D加速度計と3Dジャイロスコープ（LSM6DSL） これらのセンサーからデータを取得するサンプルプログラムが欲しいです。最終的にはここで取得したデータをNANOEDGE AI STUDIOで使用する予定です。Translated by ST community team I have the B-L475E-IOT01A2 (development board). I would like to acquire data using the following sensors included in the B-L475E-IOT01A2: Relative humidity and temperature capacitive digital sensor (HTS221) High-performance 3-axis magnetometer (LIS3MDL) 3D accelerometer and 3D gyroscope (LSM6DSL) I would like a sample program to acquire data from these sensors.

I am looking at the LSM6DSV16X MLC examples in the MLC Git Repo.I am confused by some of the register settings. For example, in lsm6dsv16x_six_d_position.h  const ucf_line_t lsm6dsv16x_six_d_position[] = { {.address = 0x10, .data = 0x00,}, {.address = 0x11, .data = 0x00,}, {.address = 0x01, .data = 0x80,}, // many lines deleted {.address = 0x02, .data = 0x31,}, {.address = 0x08, .data = 0x8E,}, // PAGE_ADDRESS: Address 0x8E not in the data sheet  I cannot find the address (0x8E) in the data sheet. I'm obviously missing something in my understanding.Any insights, guidance would be appreciated

Hello everyone, I have an ASM330LHH mounted on my selfmade board with stm32f405. The ASM330LHH works well except for the data sent by the gyroscope over the Z axis. This data is not stable at all. It wobbels very badly, quickly and with long intervals. The data around the X and Y axes is fine. How can I make the angle measurement around the Z axis stable?Hint: i use this library for configuring and getting the data out of the sensor: https://github.com/STMicroelectronics/asm330lhh-pidThank you very muchZain

Posted on February 19, 2018 at 17:42Hi all,I've tried several time to get in contact with the ST Online Support (http://www.st.com/content/st_com/en/support/online-support.html  and then the Submit Request button)  but every time I've experienced an error into an unknow 'Serena Business Manager Log In ' it give me all time Invalid User ID or Password (note I've did the login to the ST support page with success).I've no idea how to get in contact with the support team then I'm writting here, sorry if this may be not the right place to do that.just to know if others have same trouble or not.Thanks in advance.Best RegardsFabio

I'm interested in integrating multiple ST IMU(6 or 9 axis) sensors to my project. However, all IMUs will be connected in serial to simplify electrical circuit design so each IMU should has its own I2C address. Pls recommend several ST IMUs either 6 or 9 axis so I can test and connect them only by I2C bus. THX!

I would like to change the state of the INT_DRDY of LPS22DF. I have tried to change the value of INT_H_L bit in register CTRL_REG3 (12h), but it has no (immediate) effect. Is it necessary to activate the pin? I have also tried different values in CTRL_REG4 (13h), without effect.Thank you.

Hi allI am trying to debug an issue at work where we use the LSM6DSV accel/gyro IMU chip and I am running into a little problemThe result registers for the accelerometer and gyroscope both say that they return a 16-bit two's complement result, and I get the followingGyro / AccelRaw unsigned value(LOW | (HIGH << 8))Two's complement value (Signed)Result (mG or mDPS)Accelerometer X65524-12-0.732Accelerometer Y1334713347814.167Accelerometer Z1111116.771

Hello,I want to use LSM6DSM, so I got the dev-kit and tested it out.Now I decided to use this sensor and was looking for the symbols in Altium, but it is NRND, so I double checked in ST Micro web site if it was NRND, but it is still Active.As I am going to use this sensor now, I would like to make sure of guaranteed longevity. I couldn't find this in the longevity page.   

Hi guys,This has likely been covered before so please feel free to point me to it.I'm trying to set up the LSM6DSOX Pedometer to store count to FIFO, but having no luck.I am not using the Library, as it is not easily ported to my uC.Would anyone be able to highlight for me the registers I need to set up for basic operation, so that I can tinker from there?I have been able to set up the pedometer to interrupt, but not write to FIFO.I'd also be interested in the steps to read from the FIFO, but imagine that this will be easier once I'm writing correctly..Thanks,Ben

Hiis there some example project for head/device orientation detection with sensor tile box / LSM6DSV?Thx

Hi, I want to acquire an audio signal from the microphone IMP34DT05 which is connected to the SAI interface of my STM32WB5MM-DK demo board in this way: L/R -> VDD; CLK -> SAI_CK2; DATA -> SAI_D2.With the oscilloscope I noticed that I generate correctly the clock signal and the microphone send out data to the SAI but the data are not acquired into the reciver buffer.I tried different configuration in the SAI_Init() function but in any case it doesn't work.This is the configuration i'm using:hsai_BlockA1.Instance = SAI1_Block_A;hsai_BlockA1.Init.AudioMode = SAI_MODEMASTER_RX;hsai_BlockA1.Init.Synchro = SAI_ASYNCHRONOUS;hsai_BlockA1.Init.SynchroExt = SAI_SYNCEXT_OUTBLOCKA_ENABLE;hsai_BlockA1.Init.MckOutput = SAI_MCK_OUTPUT_DISABLE;hsai_BlockA1.Init.OutputDrive = SAI_OUTPUTDRIVE_DISABLE;hsai_BlockA1.Init.NoDivider = SAI_MASTERDIVIDER_DISABLE;hsai_BlockA1.Init.FIFOThreshold = SAI_FIFOTHRESHOLD_EMPTY;

I am using the chip ASM330LHH, when I write 0X40 to register 0X10, I can read the value 0X40 that I wrote, but when I write 0X60, I can't read 0X60, what's going on?

Dear SirWe are Interfacing STmicro part no MP23DB01HP which is a MEMS MIC with PDM output. We are interfacing this MIC with STM32F105RB microcontroller as it has I2S port.We are unable to find any library for this and how to calculate all the parameters required. How to convert PDM to PCM in STM32F1.Our main aim is to find DBm of sound level using the MICKindly provide us support as we had already integrated all the hardware and after that its not working