Product forums

Hello,My end node activation mode is OTAA, and is supposed to enter shutdown mode and wake up after a specified period of time period, in order to save power, the end node should skip joining the network at every wake up. I was able to skip the joining process by switching the activation mode from OTAA to ABP after the first join process, but after that, the server did not receive every packet sent from the end node like it used to when i was working with OTAA I doubt this is a good solution since a lot of packets are lostMy questions are:1) What do you think of my solution? is it missing something?2) What are my options if I want to stick to OTAA while skipping the joining process?3) Should I just go with ABP?

Can force a specific DR for LoRaWAN?I tried using: uint8_t custom_dr[7] = {0};custom_dr[3] = 1;lorawan_api_dr_strategy_set(USER_DR_DISTRIBUTION, STACK_ID);lorawan_api_dr_custom_set(custom_dr, STACK_ID);   but did not work.

Hi, I am experiencing a bug in the latest version of the Extension for VS Code. As soon as I open the extension I receive this message:"Unable to contact the STM32Cube registry, verify your Internet connection..."If I run "cube bundle list-online" in the terminal I get this:cube bundle list-online Download attempt 2 out of 5 for https://developer.st.com/bundles/BundleRepositoryIndex.json ... Download attempt 3 out of 5 for https://developer.st.com/bundles/BundleRepositoryIndex.json ... Download attempt 4 out of 5 for https://developer.st.com/bundles/BundleRepositoryIndex.json ... Download attempt 5 out of 5 for https://developer.st.com/bundles/BundleRepositoryIndex.json ... Failed to list available online bundles: Failed to download bundle repository index: Failed to send request: error sending request for url (https://developer.st.com/bundles/BundleRepositoryIndex.json)But if I install the 

OverviewDebug Authentication Discovery occasionally succeeds in CLOSED state, but Full Regression fails (“Unable to boot on RSS_DA” / “Unable to detect DBGMCU Mailbox”)Get ready for the stm32 safari! Product / Environment- Board: Custom based off of STM32H7S78-DK (MB1736)- MCU: STM32H7S7L8H6H- Debugger(s) used: STLINK-V3SET- Tool: STM32CubeProgrammer v2.19.0- ST-LINK FW: V3J17M10B6S1- Board setup used during recovery attempts:- tried altering Boot0 (boot from RSS/system flash)- tried manual reset- tried low SWD speed and hardware reset modes Summary of the issueI was attempting to recover the board after secure configuration experiments. The board was originally reachable over SWD, but after running the **`ROT_Provisioning/DA/provisioning.sh`** flow from the

Hi ST, This is just to let you know that STM32CubeMX version 6.17.0 does not generate correct cmake file for the STM32WL33 and this error results in the microntroller not starting up correctly but hangs in function  SystemInit() in system_stm32wl3x.c.   The problems is that the wrong is -mcpu is generated. The problem can be found in the file -> path/to/dir/cmake/gcc-arm-none-eabi.cmake # MCU specific flags set(TARGET_FLAGS "-mcpu=cortex-m4 ") // wrong for the WL33 # MCU specific flags set(TARGET_FLAGS "-mcpu=cortex-m0plus ") // correct for the WL33 Ola

Hi everyone,I’m currently working with STM32 Secure Boot and Secure Firmware Update (SBSFU) and integrating it with my custom application. I’m trying to design the project in a modular and scalable way for long-term use, and I would really appreciate some guidance from those who have worked with SBSFU in production. Current ScenarioMCU: STM32 (Cortex-M series)Bootloader: SBSFUApplication: Custom firmware using HAL, middleware, and CubeMX-generated codeDevelopment tool: STM32CubeIDE Challenges I’m Facing1. Shared Drivers & Middleware

Hi, I tried exporting the IBIS model from ST website. On importing model to SI tool I can see that there is no model assigned to DSI lines. It is showing NC. Can you share the IBIS model with MIPI drivers in it. or share some IBIS model which I can use for my simulation of MIPI line interface  

Hello all,I can't download the STM32CubeIDE even as I am registered. There seems to be somthing broken with the Web page. I have tried several browsers. This is what I get, so there is no download button and the table is garbled:Any help appreciated.Johannes 

Good Evening,I am a student doing a capstone project, and I have been having a massive headache with the STUSB4500 PD negotiator. I am using it to pull 15V at 3A from a power brick so I may power a handheld device downstream. We utilized a recommended layout from the datasheet itself so that we may program it ourselves. Attached below.The good news is, it can sustain loads and power our project... but the bad news is these chips have up and died about as randomly as a carnival prize goldfish, attached are pictures of my layout and schematic for this section of the board. Apologies for any amateurish mis

Hi Team,I have successfully integrated and run SBSFU with my custom application, and it is working as expected.Currently, I am transferring the .sfb file .via USB to the DWL_SLOT. Once  the transfer is complete, I trigger a reset using    NVIC_SystemReset(), and the process works fine.I have a few questions regarding the .sfb header. It contains fields such as:FW Tag (SHA-256)Header SignatureFirmware Size (FwSize), etc.My questions are:Using FW Tag (SHA-256) for validationIs it possible to use the FW Tag (SHA-256) to validate the received image in the DWL_SLOT befo

Hello I'm trying to wire up the STM32G0B1CET6N and I don't know how to use the VDDIO2 pin. What is it for and how should I wire it?

Hello!I have a custom board with STM32F746VGT6 MCU, LAN8742A Eth PHY and Ethernet socket. I would like to implement MQTT communication in my project with my board as a client. I am familiar with LwIP and FreeRTOS and use both of these libraries in my current program.I already tried using WolfSSL and WolfMQTT (and succeeded to some degree), but it wasn't very pleasant experience and I had to manually copy and change many files to make it work. I want to rewrite the MQTT implementation as the current one doesn't work very efficiently, but I don't really know where to start. I'm grateful for all suggestions!

Hello,I am trying to port the official BLE_Ota example from STM32CubeWB (WB55 project) to an STM32WB30 device, but I am facing multiple compilation issues after importing the project into STM32CubeIDE.After configuring STM32_WPAN and generating the project for STM32WB30, I get many errors such as:RTC_HandleTypeDef unknown typeIPCC undeclaredFLASH_ECCR_* undeclaredSCB_* undeclaredLL_* functions not declaredHAL and LL drivers missing or inconsistentIt seems like the project is not correctly recognizing the STM32WB30 device definition, and many peripherals (RTC, IPCC, FLASH, RCC) are not properly included or enabled.I already tried:Adding STM32WB30xx define in the compiler preprocessorEnabling STM32_WPAN middleware (BLE stack full mode)Checking stm32wbxx_hal_conf.hHowever, the issues persist and the project still behaves as if it is partially configured for STM32WB55.My questions are:

I want to vary the duty cycle of two adjacent DAC values of an STM32G473.  I am using DAC1 channel1 and channel2 for the output. I want to load DAC1s DHR12Rx registers via DMA when TIM3 hits output compare values.  I set up a memory to peripheral transfer for each TIM3 channel and set the CMAR and CPAR registers to the memory location of the DAC values and the peripheral addresses of the DAC DHR12Rx registers.   I have been able to make this configuration work for making the TIM3 OC events trigger loading of TIM20's CCR registers from memory, but so far, the DMA transfer won't load the DHCR12Rx registers for the DACs.  Are there additional configuration settings to make this work?  CubeIDE\HAL has configuration options for initializing the DAC in DMA mode, but I need multiple triggers the make the duty cycling work.   

HiI've been trying to understand what level of support is available for the H573 security features in Zephyr RTOS with mcuboot but either can't find any information or no one replies to my comments.I have a Zephyr sysbuild build working where mcuboot starts, validates the singed application in slot0 and proceeds tp boot from slot0.What I can't find or confirm is if that security features of the STM32H573 are being used or not. There doesn't seem to be any configuration relating to enabling or disabling the features.Are the security features enabled in Zephyr for the H573?I'm using the latest 4.2 version of Zephyr.CheersDave

I have an old Ubuntu 18.04 system which allows STM32CubeIDE to run, but the STM32_Programmer failed because libm.so and libc.so were wrong. I found glibc-2.30 and copied the libraries into the same directory as the STM32_Programmer lib. Now I just get a seg fault, even when trying to just get the version number:bin/STM32_Programmer_CLI --version Segmentation fault (core dumped)Is there any way to figure out what might be the problem?   

I’m currently working on implementing and testing Flash ECC on my controller. According to the datasheet, the device supports ECC, and I can see that it is managed through the FLASH_ECCR register. However, I’m facing some difficulty verifying whether ECC is functioning correctly. Specifically: I am unable to find any ECC-related flags in the FLASH status register. I’m not sure how to intentionally generate an ECC error to validate my implementation (e.g., to confirm that error handling via NMI/interrupt is working as expected). Could anyone please guide me on how to reliably trigger a Flash ECC error for testing purposes on this controller? Any suggestions, references, or example approaches would be really helpful.

Hi, I'm working on a ESL project using STM32WB09. In order to reach greater distances, is it possible to use the CODED PHY ? Thank you

Dear Community, dear STMicro, I'm trying to encrypt data on an STM32WL55JC device using the STM32CubeExpansion_Crypto_V4.5.0 library and then using Python on the PC to decrypt it again.I've taken the example code for RSA encryption from the librarySTM32CubeExpansion_Crypto_V4.5.0/Projects/NUCLEO-WL55JC/Applications/RSA/PKCS1v2.2_EncryptDecryptand adapted it.I've created an RSA 2048 bit key on my PC using this code:private_key = rsa.generate_private_key( public_exponent=65537, key_size=2048) pem = public_key.public_numbers() public_exponent = ["0x%02s" % e[i:i+2] for i in range(0, len(e), 2)] n = "%X" % pem.n n = "0" + n if len(n) % 2 == 1 else n modulus = ["0x%02s" % n[i:i+2] for i in range(0, len(n), 2)] f = open("pub.c", "w") f.write("public_exponent[] = {%s}\n" % ", ".join("%s" % s for s in public_exponent)) f.write("modulus[] = {%s}" % ", ".join("%s" % s for s in modulus)) f.c

I'm working with the STM32G4 series and using the backup registers to store time data that persists across power cycles. I have a question about VBAT brownout behavior that I cannot find explicitly documented in RM0440 or the datasheet.Background:Both RTC and backup registers are in the VBAT power domainI'm using a signature in backup registers to detect VBAT lossThe signature check works fine for complete power lossMy Question:Is it possible for VBAT voltage to drop to a level where:The RTC stops functioningBUT the backup registers still retain their contents?In this scenario, my signature check would pass (registers retained), but the time would be invalid (RTC stopped counting).Do the RTC and backup registers have the same minimum VBAT voltage threshold, or can backup registers survive at a lower voltage than the RTC requires?If VBAT brownout can cause RTC failure while backup registers persist, d

STM32CubeIDE for Visual Studio Code v3.8.0 serverRtos fails to recognize symbolFileName when attaching to running target. This causes the rtos viewer to not work properly.None working setup: "type": "stlinkgdbtarget", "request": "launch", "name": "CM7 master STM32Cube: Launch ST-Link GDB Server", "origin": "snippet", "cwd": "${workspaceFolder}/", "deviceName": "STM32H747BIT6", "deviceCore": "Cortex-M7", "serverReset": "None", "imagesAndSymbols": [ { //"imageFileName": "${workspaceFolder}/executable.elf", "symbolFileName": "${workspaceFolder}/executable.elf", } ], "serverRtos": { "enabled": true, "port": "60000", "driver": "freertos", "driverPort": "ARM_CM7" },Debug console output:RTOS proxy: STMicroelectronics RTOS Proxy. Version 0.18.1 Copyright (c) 2026, STMicroelectronics. All rights reserved. Failed generate debu

Hello,I'm designing a 2 layer PCB using STM32WL for LoRa operations at 433MHz and need a review of my RF layout. The board is JLCPCB 2 layer standard FR4, 1.6mm thick 1.46mm core, 1oz copper, 50Ω microstrip at ~2.8mm width, about 38mm long. I have placeholder caps/inductor to be populated after board fabrication. I am seeking expert opinion for:Trace width & impedance - does 2.8mm yield 50ohm given FR4, 1oz copper, and 1.46mm dielectric height?Critical length - Are there implications for 38mm length on transmission-line behavior?Taper - Taper starts 5mm in. Are there optimal lengths for tapers? Should I taper for shunt pads?Stitching vias - Recommendations for via spacing for this trace width? Every 5-8mm?Test points - Recommendations for RF test points without effecting impedance?Any other best practices or tips would be helpful. I thank you for any guidance.Best, John

I am trying to integrate Crypto lib to NUCLEOF303RE Board, Any guide or any suggestions would help 

Hi everyone,I’m working on a 4-layer PCB design using the STM32WL (based on the Nucleo WL55JC reference design).For the RF section, I followed the same layout approach as the Nucleo board, including the layer stack-up and RF trace widths.The only difference in my design is that I have some GPIO signals routed close to the RF section. These signals are routed on the 3rd layer, while I am still maintaining solid ground planes on the 2nd and 3rd layers underneath the RF section.I would like to clarify:Is it acceptable to route non-RF signals on the 3rd layer near the RF section if solid ground planes are maintained?Are there any risks (e.g., noise coupling or RF performance degradation) with this approach?Additionally, if I modify the layer stack-up:What parameters need to be adjusted (e.g., RF trace width, impedance matching, ground reference)?Are there any recommended guidelines for maintaining RF perf

Hallo,is it possible to detect in my code whether it was just loaded and started under debugger? The code should behave deifferant as usual because flash loader writes into RAM and .noinit section is modified because of this.I have already checked RSR register. It looks the same as after software reset: CPURSTF, PINRSTF and SFTRSTF are high.Moreover RSR gegister is independent from debug configuration: Debugger / Reset behaviour. I use ST-LINK v3 with ST-LINK GDB server.