STM32 MCUs

Hello everyone.I have recently made my own STM32 board based on the STM32F405. After soldering all the components and testing all pads and connections, finding them to be wired correctly and checking that the 3.3V is being supplied to all the correct pins, I tried to upload some code, but to my shock, the STM32F405 isn't establishing a connection via the ST-Link V2 nor the USB cable. After trying multiple fixes, I suspect the issue might be the STM32F405 chip that I got off AliExpress itself. Before taking any further steps to replace it, I decided to post a question here for review in case the problem was in my PCB design. And sure enough, I had misplaced the chip pin due to the faulty pinout diagram I used as reference.I have since fixed the chip's orientation and rechecked all pad and pin connection

I need support for the design of STM32WL30XX PCB Antenna. Are there reference designs available for the PCB antenna?Specifications:Two layer board Output power 10dBm in the 868MHz band.   

NUCLEO-F767ZI I'm trying to use the LwIP middleware which I have enabled in MX. First I'm trying to check if an ethernet cable is attached or not. I have setup UART3 to use printf (which works as expected) I've set the callback in lwip.c to print when the cable is removed or plugged in or so I thought but I get no message when I connect or disconnect the cable. The LEDs on the socket light up when the cable is connected, so the board at some level does see the cable. What am I missing here? EDIT:: LWIP_NETIF_LINK_CALLBACK was enabled in MX // In main.c MX_LWIP_Init(); /* USER CODE BEGIN WHILE */ while (1) { MX_LWIP_Process(); /* USER CODE END WHILE */ /* USER CODE BEGIN 3 */ } /* USER CODE END 3 */ // In lwip.c the callback function that is registered in MX_LWIP_Init() static void ethernet_link_status_updated(struct netif *netif) { if (netif_is_up(netif)) { /* USER CODE BE

Hello STM team,   We are working to interface the  NUCLEO-U5A5ZJ-Q and nRF7002-DK using QSPI. We are using vanillas zephyr. We are able to built the code for SPI. But can not be able to built for QSPI. It will be very helpful if you provide a proper support to interface this.

Hello,   I configured a timer in STM32CubeMX2 to use 2 channels (HAL_TIM_CHANNEL_1 and HAL_TIM_CHANNEL_3). After the mx_system_init() I use the following code: hal_tim_handle_t *htim5 = mx_tim5_gethandle(); if (HAL_TIM_OC_StartChannel(htim5, HAL_TIM_CHANNEL_1) != HAL_OK) { return (-1); } if (HAL_TIM_OC_StartChannel(htim5, HAL_TIM_CHANNEL_3) != HAL_OK) { return (-1); } if (HAL_TIM_Start(htim5) != HAL_OK) { return (-1); }  The first channel starts as expected, but when I attempt to start the second channel the code causes an assert in HAL_TIM_OC_StartChannel: /* Check and update the channel state */ ASSERT_DBG_STATE(htim->channel_states[channel], HAL_TIM_OC_CHANNEL_STATE_IDLE);   Do I need to do anything different?   Regards, -Gil

The entry for address 0x1FFF7838 in Table 17 ( Organization of option bytes) shows FLASH_PCROP1ASR as the "Corresponding option register" - it should be FLASH_PCROP2ASR.

   Trying to Interface ADS1293 with STM32U5 for 3-Lead ECG – Need Help with Lead II Data Hi STM32 Community :waving_hand:, We’re trying to build a 3-lead ECG signal acquisition setup using the ADS1293 analog front-end connected via SPI to an STM32U5G9ZJT6Q microcontroller. The goal is to capture and plot Lead I, Lead II, and derive Lead III using TouchGFX.  What’s Going Well: We are able to receive and plot clean ECG data for Lead I (RA - LA) using CH1 of the ADS1293. SPI communication is stable, and the plotting is handled through TouchGFX without lag. Sampling is working at 500–1000 Hz using a DRDY-based interrupt routine.

hello ST Community,There's an STM32 board in a USB pen drive format with a small flash memory capacity and only a few pins (3-5 pins) for UART serial communication. On this STM32 board, inside the USB pen drive, I can program the dedicated software for serial communication.If it exists, can you tell me the model and serial number? I can't find it online.Thanks for the information.

Hi all.I wish disable auto PAD disable CRC append.  Send packet use low_level_output(), before call HAL_ETH_Transmit_IT()I set TxConfig.ChecksumCtrl = ETH_CHECKSUM_DISABLE; TxConfig.CRCPadCtrl = ETH_CRC_PAD_DISABLE;but packet allways pad to 60byte,if use TxConfig.CRCPadCtrl = ETH_CRC_PAD_DISABLE;, no packet outputif use TxConfig.CRCPadCtrl = ETH_CRC_INSERT;  output fine but have 4byte crcr append.How to do , NO-PAD NO-CRC send packet?

I'm trying to interface with a W25N NAND flash chip on an STM32H7, over QSPI. I've only got consistent output out of the reads, and even then, I notice the system hangs forever and can't accept anymore input after a read. Everything else will hang immediately, even a print statement to the terminal at the top of the function won't appear, and the whole system hangs.   From some similar issues I found online, I thought it would be a timing issue, and so I tried to implement a status register check. That's my first function in my excerpt below. However, this function couldn't even run alone without again hanging the system (meaning something else is causing the resets, program, clear, and even status check to hang). What else could be the issue that stops everything from running?   Any advice much appreciated. Thanks very much in advance.

Hardware: STEVAL-MKI109D (STM32H563ZI)CubeMX: 6.17.0CubeIDE: 2.1.0Connection: USB-C directly to STM32H563 USB OTG (no ST-LINK chip)PROBLEM:I need USB CDC Virtual COM Port in a bare-metal application(no RTOS). CubeMX 6.17.0 for STM32H563 only offers:- USBX (requires ThreadX)- ThreadX- FileX- LevelXClassic USB_Device middleware (usbd_cdc_if.h / CDC_Transmit_FS)is NOT available for STM32H5 series in CubeMX 6.17.0.USBX requires ThreadX RTOS. Without ThreadX running,MX_USBX_Init() causes the board to crash silently —after DFU flash the board is completely invisible on USB(no lsusb entry, no /dev/ttyACM*).QUESTIONS:1. How do I implement USB CDC on STM32H563 WITHOUT ThreadX?2. Is there a way to enable classic USB_Device stack for STM32H5in CubeMX 6.17.0?3. Is there a bare-metal USBX CDC example that does NOT requireThreadX for STM32H5?4. Can

While I was experimenting with the 'L476 Disco, the RM wording goes across multiple families, so it may be relevant to most/all of them. In particular, for Shutdown mode (which is supposedly the lowest-VDD-consumption mode), the RM says: What does "switch to Backup domain is not supported" mean, exactly (assuming VDD and VBAT have separate sources)?  as soon as Shutdown mode is entered, RTC (backup domain) is switched to VBAT even if VDD is present, potentially draining the VBAT source (battery, capacitor) in Shutdown, while VDD is present, RTC is powered from VDD; but when VDD is removed, RTC is *not* switched to VBAT, resultin

Hello, is it possible to boot FSBL and load application from SD card upon powerup, bypassing onboard flash?  I didn't see any clear guides on this procedure.Thank you

In testing the LoRaWAN_End_Node_LBM application supplied with STM32CubeWL-1.5.0 release I found that the output power is substantially lower than the same test setup with the LoRaWAN_End_Node application supplied with STM32CubeWL-1.4.0.  This testing was conducted only using the US915 region setting.First I found that the EIRP was being defined as 16 dBm in Middlewares/Third_Party/LoRaWAN/smtc_modem_core/lr1mac/src/smtc_real/src/region_us_915_defs.h when it should be 24 dBm.#if defined( LR11XX ) || defined( SX1262 ) || defined( SX1268 ) // region is 30 dBm but radio is 22 dBm ERP (+2 to EIRP) #define TX_POWER_EIRP_US_915 (24) // define in dbm #else // region is 30 dBm but radio is 14 dBm ERP (+2 to EIRP) #define TX_POWER_EIRP_US_915 (16) // define in dbm // TODO must be checked, SX126x dependent for the max power #endifSince the project compiles with the preprocessor symbol

I’m designing a board using the STM32U083MCT6TR, and my system supply voltage is VDD = 1.8 V.The design does not use USB at all. The datasheet specifies that VDDUSB normally requires 3.0–3.6 V for USB operation, but it’s not fully clear what the correct connection is when USB functionality is not needed. My question:What is the recommended way to handle the VDDUSB pin when USB is unused and the MCU is powered at 1.8 V? Should VDDUSB be tied to VDD (1.8 V)? Should it be left unconnected? Or is another configuration required? If anyone has experience with the STM32U0 series or clarification from ST, I’d appreciate the guidance. Thanks, -Tal

Hi everyone,I’m currently working on a project involving LR-FHSS and I’d like to know whether there are STM32-compatible end devices and gateways that already integrate LR-FHSS-capable radio chips.From what I’ve found so far:End Devices (sensor/node): They must use a chip from the SX126x family.Gateways: They need to be based on the SX1302 or SX1303.Before I start designing custom hardware, I’d like to confirm whether there are existing commercial end devices or gateways that already include these chips with LR-FHSS support.If anyone has experience with this or can recommend specific hardware, I would really appreciate it.Thanks!

This is probably an old hat to most of you here but I'm facing this problem momentarily:Using an STM32F103CBT6 (Blue Pill) where GPIOB Port is used already with the following PB3 - SPI1_SCKPB5 - SP1_MOSIPB6 - Some Interface Function (OUTPUT)PB7 - Some Interface Function (OUTPUT)   I want to use PB0, PB1, PB4, PB8, PB12,PB13,PB14,PB15 for a keyboard matrix scan and outputa running pattern to these pins. Writing the bits should be nondestructive what the remaining bits is concerned. At the back of my mind I recall something like BSRR, but could someone help me to get on the right track?I'm using HAL in this app (under STM32CubeIDE).

Hi, I am working with the SBSFU_Boot on the STM32U5A9 chip. After the SBSFU_Loader has written the update image into internal memory, a reset happens in order for the SBSFU_Boot to write the image to be booted. When performing the update, it ends up in a process where it has to do some encryption. The SAES engine is initialized successfully, and then AES_Encrypt is called. This keeps on failing because a read error is reported in the SAES->SR reports a read error upon enabling the SAES peripheral. It should be noted that the initialization and encryption sequence is strictly followed per instructions in RM0456 Rev 6 sections 50.4.4 (Initialization of SAES) and 50.4.8 (ECB/CBC encryption sequence) respectively. What am I missing?

@FBL Can you explain me about buffer descriptor table (BDT)? Is it fixed?I have got behavior that I can't explain.Dumping packets on host I got wrong data. Length is ok, but data is wrong.In BDT I wrote correct address and length. Data wrote in pma (adress that is in BDT) is correct.But when I stop in debugging address in BDT is changed. As I think in BDT there is a place for each endpoint (or it is like cyclic buffer?)What I found if I set break point with "if" condition, just before sending address in BDT is OK, and data on host is OK. It seems to me that I am working incorrectly with BDT.

Hello,I am following the blog "Implementing Debug Authentication on STM32H5 using CLI tools" (https://community.st.com/t5/stm32-mcus/implementing-debug-authentication-on-stm32h5-using-cli-tools/ta-p/622308) to provision my STM32H533RE based custom board on which i have configured secure word only(All the peripherals configured as secure) and i have disabled Non Secure Project from "Project Manage" tab of STM32CubeMX, and I am now stuck with the device in CLOSED state with no way to regress.Environment:Board: NUCLEO-H533RE (STM32H533RET6)STM32CubeProgrammer:&nbsp

I am coding from the scratch to learn how STM32 works with MIPI-DSI LCD, because I am going to use customized MIPI-DSI LCD. I refer to the official code, but some incorrect content as below:official default code: in main.c , static void MX_LTDC_Init(void):// SETVCOMuint8_t InitParam60[4] = {00, 00, 00, 0xC0};if (HAL_DSI_LongWrite(&hdsi, 0, DSI_DCS_LONG_PKT_WRITE, 4, 0xC7, InitParam60) != HAL_OK){Error_Handler();}BUT, I check HX8379C datasheet (LCD control ), SETVCOM command is (B6h), and there is no 0xC7 command ?so what's this code for? and HX8379C datasheet dosen't mention initial sequence , how do we know that we need to set SETPOWER, SETD

Split from WiFi or WiFi+BT modules architecture and parts recommendations as that's really a separate question!Thank you @Andrew Neil I didn’t explain myself very clearly. The part I’m mainly interested in is the audio side — specifically, a microcontroller with some kind of audio I/O capability, such as microphone input and speaker output, for recording (and then saving to uSD - perhaps using DMA if it makes sense). I’ve never worked with microcontrollers for audio recording before, so if such micro is not available, I’m also open to a low-cost solution/architecture that uses external components.Thank you

(I tried to submit a ticket but the system seems broken, giving an obscure error about an incorrect zip code).I need to confirm which version of STM32 is placed on a board. There are two versions, GP and PD. The datasheet does not really specify how the top marking is different for the two versions.   

We want to use the STSPIN32G0A1 evb, we cant find its schematics of it.

Hello, in the STM32H753xI datasheet, Table 11, "Total current into sum of all VDD power lines (620mA)," is the voltage condition VDD = 3.3V? I would also like to know the current at VDD = 1.8V.