STM32 MCUs Products

Hello everyone,I am currently working on a project using the STM32H755 microcontroller, and I am facing an issue with the program getting stuck in the `Reset_Handler` during debugging. Specifically, the code halts at the instruction `ldr sp, =_estack`, which sets the stack pointer, and does not proceed further.### Project Setup:- **Microcontroller**: STM32H755- **Core**: Only using the Cortex-M7 (CM7) core, with Cortex-M4 (CM4) code generation disabled.- **Debugger**: ST-LINK V3- **IDE**: STM32CubeIDE- **Firmware**: No custom firmware for CM4, only CM7 is active.### Steps Taken:1. I created the project with STM32CubeMX, configured it to use only the CM7 core (CM4 is disabled).2. During debugging, the code reaches `Reset_Handler` but gets stuck at `ldr sp, =_estack`.3. I have tried stepping through the code and confirmed the program halts at the stack pointer initialization.### Possible Causes Considered:

Hi, I'm stuck on a problem with setting PWR_CR_VOS on NUCLEO-32 STM32L031K6- I want to select HSI16-PLL as clock source- VDD is 3.3V- FLASH latency is set to 1WSBut I can only set PWR_CR_VOS to RANGE 2 and RANGE 3.RANGE 1 cannot be selected, so I can't set HSI-PLL to 32MHzwhere am I going wrong?Example code:// Set the Flash ACR to use 1 wait-state// and enable the prefetch buffer and pre-read.FLASH->ACR |= (FLASH_ACR_LATENCY | FLASH_ACR_PRFTEN | FLASH_ACR_PRE_READ);//----------------------------------------------------// 1. POWER ENABLE CLOCK and VOLTAGE REGULATOR//----------------------------------------------------// APB2ENR->SYSCFGENRCC->APB2ENR |= RCC_APB2ENR_SYSCFGEN;// APB1ENR->PWREN: Power interface clock enable bit for PWRRCC->APB1ENR |= RCC_APB1ENR_PWREN;// PWR: VOS[11:2] bits (Voltage scaling range selection)// !!! 0x0UL: FORBIDDEN// 0

HI, how do I read the temperature value of a STM32C071 ADC and convert it into °C using DMA? I cant find any formula in the datasheet. BR Matthias

I am working on an STM32 device with TrustZone enabled, and I am using the RTC with backup domain powered by VBAT. My RTC is initially configured while VDD is present, and after power-off, the time is supposed to be retained using VBAT.When I use the LSI clock, the RTC initializes correctly, and the time is retained across power cycles. However, I observe some drift, so I switched to the LSE clock. With LSE, the drift problem is gone, but a new issue appears:The RTC time is NOT retained when the system is powered from VBAT only.After removing and restoring VDD, the RTC resets instead of keeping the previous time.Details :TrustZone is enabled in the project.RTC + Backup domain is configured in the secure domain.Powering the RTC from VBAT works when LSI is used but fails when LSE is used.LSE crystal is soldered and oscillation appears stable.VBAT is present and verified during power-off.No backup registers or RTC clock

I want to use stm32f103rct6 inner RTC, I write some code as below to active RTC, But I found I couldn't set DBP bit of PWR_CR reg to 1,   __HAL_RCC_PWR_CLK_ENABLE(); __HAL_RCC_BKP_CLK_ENABLE(); LL_PWR_EnableBkUpAccess();when I debug the reg as below(gdb) x/2x 0x40007000 0x40007000: 0x00000000 0x00000000 

Hi,I am currently trying to update my STM32L433 on my custom board and I am having some issues with the RDP level 1.When receiving the blank boards (not programmed yet), I use a RPI with OpenOCD and a JTag to update the chip. When I set the RDP level 1, I can't seem to find a way to restart the device with having to do a manual power cycle. I am missing something?This is what I do :initreset initstm32l4x mass_erase 0sleep 50flash write_image "$name"sleep 50reset runAfter first programming, I am trying to update through USB dfu using a custom application in C# based on CubeProgrammerApi. I am able to boot the device in the Bootloader (I have control over the Boot0 and Reset pins), to connect to it, remove the readout protection (using connectDfuBootloader2) and flash the new firmware.I am unable after that to set the readout protection using sendOptionBytesCmd("-ob rdp=0xbb") (gives me an error) and if

Split from: Power Supply for STM32F030 Cortex TSSOP20 VDDA and VDD pin; specifically this post.@TDK wrote:that satisfies the condition. But only the "VDDA >= VDD" condition - it doesn't satisfy the "VDDA must be first" condition. As noted, I suspect that the 2nd condition is incorrectly stated; I guess it should say, "VDD must not come after VDDA" or similar ? @TDK wrote:That is the most c

I am trying to use SWD for printing using ITM_Sendchar, Printf not calling _write, I tried to put breakpoint and see, But it is not hitting breakpoint  

Hi everyone, I’ve been stuck on a CAN communication issue between two boards: STM32F429 Discovery (Classic CAN) STM32H743XIH6 (FDCAN) I’m trying to establish CAN communication between them. Currently, the F4 board can transmit and receive data correctly. The H7 board, however, can transmit but is unable to receive any messages. I’m wondering if the issue is due to the H7 using FDCAN (Selected Classic CAN on H7 Board .ioc file) while the F429 uses Classic CAN. If this difference causes compatibility problems, please let me know. Otherwise, if you know what might cause the H7 to fail in receiving classic CAN frames, I would really appreciate your help. Thanks in advance! would be great

I have multiply\accumulate operations that I want to streamline by using the FMAC. For my application I will be loading the X1 buffer by DMA from peripherals and I don’t want to use circular mode. Documentation mentions ‘vector mode’ which matches what I need, but I don’t see documentation anywhere detailing how to make it work this way. Is this really supported?I'm researching how to improvise by tweaking the R\W pointers, but I'm not sure it is allowed either:Is there a way to keep the pointers from advancing after setting FIR and START bits?Can I reset the read pointer to the base address before executing the start commands? 

In a recent design I needed an additional pin and I configured the PA13 / SWDIO pin as a GPIO input.All going fine, code works, but then this happened: After I program the chip in automatic mode and set the option byte rdp to 0xBB I can't connect again with the programmer. Programmer sais: No STM32 Target found...I tried different modes and reset modes, no luck.The readout protection alone is not the issue, I have been able to connect and reset this on other designs after it was set. The difference here is that the processor is using the SWDIO as an input when running. I thought this would not affect it as it should be available to the programmer directly after reset. The code without the readout protection set does not prevent me from connecting either. This must be the combination of both somehow.Any smart ideas how to circumvent this and connect the programmer again?Regards, PeterP.S. I know you like to look at the schematic for a custom

Hi, We are planning to use  PSRAM chip apmemory (APS12808L-3OBM) with STM32U575QII6. Please check pin assignment from STM32 to PSRAM chip And also please share the schematic and layout guidelines for STM32U575QII6 OCTASPI to PSRAM chip integration. And general layout guidelines. Thanks.

I'm using an STM32H725 to communicate with an i2c sensor. I'm using the I2C4 bus with the HAL DMA functions. I also enabled the BDMA channels for the rx and tx and respective interrupts. The problem is that the complete rx/tx callbacks are not triggered. I found that this could be related to the problem described here: https://st.my.site.com/community/s/article/FAQ-DMA-is-not-working-on-STM32H7-devicesAny solutions to this problem?

i use STM32N6570-DK to do a simple project but i cannot get any useful info via printf() on SWVITM data console. (1) I add some code in systemcall.c for printf() on SWVITM data console or UART1 via a "define" in my main.c. (AS many professionals suggested on the net)   Now i can get info correctly by using uart but not the SWVITM. (2) I also choose SWD under DEBUG in .ioc config. Three wires are used. SWO is populated.(2) when i use SWV ITM data console, the display is just messy symbols. AI told me that it is either due to the wrong Baud rate or wrong encoding. The default is UTF-8. I tried different Baud rates and coding standards. No one works. The same messy display (3) I have watched a few youtube clips and followed their methods. No one works either. Has anyone got the correct display of printf () in   SWV ITM data console ON THIS STM32N6570-DK?Thanks a lot in adv

Now I want to know whether the STM32C011J6Px has a Low-Power Timer (LPTIM).Currently, we are planning to use the STM32C011F6P6 MCU in STOP Mode 2. Since we do not have any external pin interrupt available as a wakeup source, we are planning to use the LPTIM to wake up the system every 1 ms, read one analog value, and then go back to deep sleep again.I checked the datasheet and found the following list of timers for this series. Can you please confirm whether this is correct, or let me know if I am missing anything?TIM1 – Advanced-control 16-bitTIM3 – General-purpose 16-bitTIM14 – General-purpose 16-bitTIM16 – General-purpose 16-bitTIM17 – General-purpose 16-bitIWDG – Independent WatchdogWWDG – Window WatchdogSysTick – System Timer

Hi, I am using STM32H743ZI Nucleo 144 board for one of my application. As per the observations I got the utilization factor with STM32H743 is 35% where as with STM32H752 it was 60%. We have not initialized any crypto or secure features on STM32H753 but still i can see drastic change in the utilization factor. Have you observed this before? Any suggestions to check? 

Hi,In STM32H742xI/G datasheet (DS12110 Rev 8), the SRAM3 memory block is not specified in the "Table 7. Flash memory and SRAM memory mapping" but I can see the availability of the SRAM3 in the generated .map file.Can someone please confirm, it is typo mistake in datasheet or really not available for STM32H742xI/G?

Hi We are using an STM32U073CCT6 on a battery-powered board. We need to put the processor in low-power mode to increase battery life. The current in STOP MODE 2 is about 20uA. To address some issue related to the power supply and our hardware, we put the processor in Shutdown Mode and obtained a current of 2uA. How could we reduce the consumption in STOP2 mode? We have already deinitialized all peripherals before entering stop mode 2.   BRGilberto

Hello there, I'm playing with the NUCLEO-H743ZI2 board and having difficultis with PTP. When TSIE (MACIER is set the interrupt is getting retriggered endlessly. I've tried to clear TSIS by reading both MACISR as well as MACTSSR (TXTSSIS bit set). The manual states this is a way to achieve this, but neither register is cleared. BTW, the alternate way (MACCSRSWCR) semes not being supported altho I've tried that as well. Just at the interrupt entry: macisr = ETH->MACISR; // 0x1000 mactssr = ETH->MACTSSR; // 0x8000 macisr2 = ETH->MACISR; // 0x1000 mactssr2 = ETH->MACTSSR; // 0x8000 macisr3 = ETH->MACISR; // 0x1000   Where am I doing the wrong thing? Thank you for any input.The ST Community moderator has edited the post to comply with the code sharing guidelines. In the

Hi i am struggling to make SPI work on my nucleo-h723z board. I am using Cubemx to configure and i press when asked to used the default setup for the nucleo board when creating the project.CubeIDE is v. 1.15.1CubeMX is v. 1.11.1my code is very basic: while (1) { /* USER CODE END WHILE */ /* USER CODE BEGIN 3 */ uint8_t address = 0x80; HAL_SPI_Transmit(&hspi4, &address, 1, 100); HAL_Delay(1000); }I have put a logic analyzer on the clock, MOSI and MISO, but no matter what, I can only see the clock signal. 

Post edited by ST moderator to be inline with the community rules for the code sharing. In next time please use </> button to paste your code and a linker script content. Please read this post: How to insert source code.i, I am using STM32C092CCT6 with FDCAN.I transmit one CAN frame every 100 ms (even tried 50 ms).But on the receiver side, I always receive frames only every ~497 ms.It looks like something is delaying or buffering the frames.What I want to know:Which FDCAN settings could cause the frames to appear only every ~497 ms?My problem summary:Tx interval configured: 100 ms → Rx sees ~497 msTx interval configured: 50 ms → Rx still ~497 msSo the transmit timing is not coming out correctly.Re

I've attempted to get an interrupt when one of the three CAN transmit mailboxes empties. In MX:It generated: /* CAN interrupt Init */ HAL_NVIC_SetPriority(CAN_TX_IRQn, 0, 0); HAL_NVIC_EnableIRQ(CAN_TX_IRQn); HAL_NVIC_SetPriority(CAN_RX0_IRQn, 0, 0); HAL_NVIC_EnableIRQ(CAN_RX0_IRQn); HAL_NVIC_SetPriority(CAN_RX1_IRQn, 0, 0); HAL_NVIC_EnableIRQ(CAN_RX1_IRQn); HAL_NVIC_SetPriority(CAN_SCE_IRQn, 0, 0); HAL_NVIC_EnableIRQ(CAN_SCE_IRQn); I am using the HAL method HAL_CAN_AddTxMessage. This method seems to be working because

Hi,Vous avez dit :I’m using the STM32H753ZIT6 in my design and I’m looking for clarification on the correct way to connect the VCAP pins. Since the LQFP144 package does not support the VDDLDO pin, what is the recommended capacitor configuration for VCAP?Should I use 2 × 100 nF capacitors to GND, or 2 × 2.2 µF to GND?Additionally, if there is no VDDLDO pin available on this package, how does the VCORE receive its internal supply voltage? Is there an internal voltage regulator that is powered directly from VDD?Thanks in advance for the guidance! 

Need getting-started help with STM32C011J6M6 MCU and USART1 in single-wire Async mode (using STM32Cube toolchain and C language.)The hardware configuration is just  the STM32C011J6M6 MCU (8-pin SOIC package) with one pin (pin 1) pulled up (4.7K to 3.3V). Intent is to use this in single-wire Async mode to communicate with outside world. All other MCU pins have similar pull-up resistors but are not otherwise connected. Power to the MCU for this test is furnished by the STLINK device. The test is using programmed I/O (no DMA,  no interrupts.) The test program solely is written to experiment with the USART1 in single-wire mode on this device; there  are no other aspects being tested or included. Tools in use:IDE 1.19.0MX 6.15.0PROG 2.10.0 Used STM32CubeMX to generate code template (targeting STM32CubeIDE), STM32CubeIDE to build the example (C-language) program, and STM32CubeProgramme

Hi, I have an STM32C092RCT6U development board and I am trying to perform UART-based bootloading. My board has a B3 button for selecting the boot mode. I am using the Flash Loader Demonstrator to flash the application, but I keep getting the following error:“No response from the target, the bootloader cannot be started.” I also tried using STM32CubeProgrammer. I configured it for UART and attempted to connect, but the connection fails with the error: “Activating device: KO. Please verify the boot mode configuration and check the serial port configuration. Reset your device and try again.” I am using a USB-to-UART module connected to PA10 (RX) and PA9 (TX) with the lines crossed (TX→RX, RX→TX).I also tested using inbuilt Virtual COM port, However, the device is unable to communicate and does not en