STM32CubeMX (MCUs)

The Infineon AIROC-Wi-Fi-Bluetooth-STM32 Expansion Pack is an extension of the CMSIS-Pack standard established by Arm.The pack is compliant with the full CMSIS-Pack standard, with additional requirements/restrictionson the final pack to meet the STM standard. GitHub space: https://github.com/Infineon/AIROC-Wi-Fi-Bluetooth-STM32/releases/tag/release-v1.8.0What Changed?v1.8.0Support the STM32N6570-DKUpdate the H1combo clm to v3Update the btstack-integration to v.6.2.0Update the btstack to 4.1.4v1.7.1Update Wifi firmware 4373/4373E TO 13.10.246.356Update the wcm application to version 3.6Supported STM32 Boards and MCUSTM32N6570-DKSTM

Follow-on from CubeMX code generation from command line.I am posting again in hopes of getting meaningful answer.I tried creating a simple script text file to automate code generation for my project. The script file has all of three lines:config load DCC_tester.iocgenerate code .exitThe feedback I got on why it did not work was my .ico file was corrupted. To prove this was not the case I used a very simple project file using one of your example projects from one of your released STM32H5 bundles.The only modification I made was changing the name and making it a cmake project.I am running on Windows 11 with CubeMX installed using all defaults.I can click on the .ioc file from Windows Explorer and the MX IDE opens just fine. I can click the "GENERATE CO

A new question moved from this thread. Thank you a lot! But still I have many questions regarding this. Like this one: I have configured the ADC with the Temperature Channel and Vref int channel to be used with DMA. However in many examples they show how to configure the rank for the DMA but the rank option is missing within my CubeMX:   Is this a bug or I'm missing something?

In the STM32CubeMX configuration interface, there are two identical options here.They can be configured into different options.

I would like to automate code generation of my .ioc file using CubeMX from command line or PowerShell.AI says its possible with the -q (quiet mode) option but it does not seem to work.

I recently switched to Mac Tahoe 26.1 and it seems since then stm32CubeMX 6.15 is not listing the contents of my Documents folder anymore. It doesn't seem like a rights management issue sincethere were no changes to the Documents rightsthey are identical to sibling folders which CubeMX would properly enumerateAnd yes, the folder does have contents and is not empty as shown in the screenshot from the file open dialog attached.Anyone experiencing similar issues? How to come around that?Best,Oliver

as the image, after code generate in MX, instances chooser UI's graphic resolution is broken. I cannot choose any botton and projects. please solve it.

Hello everyone, I'm creating a TIM3-based project using CubeMX. I'm using the Nucleo-H755ZI development board, which features the STM32H755ZITx dual-core MCU.I've completed all the necessary configurations—GPIO settings, TIM settings, SYS, and PROJECT settings. However, when I click "Generate Code," it creates the main.c file but does not generate the xxx_FLASH.ld linker script file. My selected Toolchain is STM32CubeIDE. I'm using CubeMX version 6.15 and CubeIDE version 1.19.Does anyone have any idea what might be causing this issue? 

Hi, may I confirm whether the STM32H755 supports only the muxed PSRAM configuration? I want to experiment something with an unmuxed connection with separate data and address. Is there a work around on this or is it an internal design that I cannot change

Hello,I’ve created a custom STM32Cube Pack using STM32Cube Pack Creator and added an example project inside the pack. The pack builds successfully and installs correctly in CubeMX. However, the example I added does not appear in the CubeMX Example Selector.It appears in "Repository/Packs" in my user folder in c:/Details:Pack created with STM32Cube Pack CreatorExample project added under the Examples folder in the pack structurePack installs fine and is visible in CubeMXThe example does not show up in the CubeMX Example Selector listQuestions:Are there specific requirements or metadata (e.g., .pdsc file entries, example description XML) that must be included for CubeMX to recognize and display the example?

Posted on November 09, 2016 at 15:03Hello,as I understood, x-cube-cryptolib is a plugin for the cubemx software, isn't it?But when I run SRM32CubeMX, Version 4.17.0 and use Help->Install new libraries-> from local and select en.x-cube-cryptolib.zip, I get this error:This Package version is not managed on this version of STM32CubeMX.What's wrong?  #cubemx

OverviewAfter migrating a project from CubeMX v5 to v6 (DB 6.0.150), the pin assignment for I2C1_SCL (PB8) and I2C1_SDA (PB9) is automatically removed when SPI1 is enabled.This issue did not occur in CubeMX v5, and on real hardware both I2C1 and SPI1 can operate simultaneously. Steps to ReproduceOpen a project created in CubeMX v5 and migrate to CubeMX v6Assign PB8 → I2C1_SCL, PB9 → I2C1_SDAEnable SPI1 (Full-Duplex, Master or Slave)PB8/PB9 immediately lose their I2C1 assignmentsIn some cases, I2C1 disappears entirely from the .ioc, and MX_I2C1_Init is no longer generated EnvironmentMCU: STM32F103CBTxCubeMX: 6.15.0DB: 6.0.150Firmware Package: STM32CubeF1 v1.8

TitleFDCAN Nominal Time Segment 2 (NTSEG2) Parameter Missing During STM32CubeMX Project Migration, Leading to Incorrect Baud Rate CalculationProduct/ToolSTM32CubeMXVersion Found (New)V1.16.0 (CubeMX: V6.11.0 or newer)Target FW PackageSTM32Cube FW H7 V1.12.1Original Version (Old)V6.9.1Original FW PackageSTM32Cube FW H7 V1.11.1MCU FamilySTM32H7 Series (FDCAN Peripheral)SeverityHigh - Causes incorrect calculation of the critical commu

This morning I updated my CubeIDE to 1.19 from 1.18.  I assume MX updated too... don't know how to check the MX version.After updating and then opening and migrating my project to 1.19, my OCTOSPI settings and the "octospi.c" file were gone.  When I try to set things back the way they were in 1.18, there is no longer an option for "Quad SPI -- MULTIPLEXED --".  My circuit has a flash IC and a RAM IC sharing the bus on Data [3:0] (Port1 IO[3:0] -- MULTIPLEXED --).  This has been working when using IDE 1.18, but now I'm stuck.How do I setup the new MX to multiplex OCTOPSPI1 and OCTOSPI2 ?

New question split from this thread. Hello, Thank you for your response. I have double-checked and found that the 6.10 version also cannot be configured in this way. I will adopt the single-line mode on the next hardware version. However, there is still a question regarding the configuration of can in version 6.16. Why must the sum of the two parameters in the following figure be 32? Otherwise, there will be a warning. In version 6.13, this issue does not exist.

 Hi everyone,I've noticed a change in UART pin configuration behavior from CubeMX 6.10.0 to 6.16.0 that has caused a practical issue:Before (v6.10.0): It was possible to configure only the RX or TX pin for an asynchronous UART, enabling "receive-only" or "transmit-only" modes.Now (v6.16.0): Both TX and RX pins must be assigned simultaneously; otherwise, the UART peripheral cannot be enabled.Problem: This wastes a GPIO pin. My specific use case is an SBUS receiver (one-way communication, requiring only the RX pin). Now I'm forced to allocate an additional TX pin that will never actually be used.Questions:1. Is this a permanent new requirement in CubeMX, or is it a GUI bug in version 6.16.0?2. What is the technical reason behind this change?3. Is there any way to achieve a true single-pin UART configuration under the new version?Thanks for any insights.

Hello,I have a Nucleo-L496ZG-P evaluation board that has a STM32L496ZGT6PU processor installed on.The processor has 2 CAN bus peripherals, and I would like to run an example that uses either of those.The STM32CubeMX has CAN examples, but not for STM32L, just for STM32F family.Could anyone recommend how I can import the CAN examples from the STM32F into the nucleo board.Thanks, D 

H745 startup files are located in "CM7/Core/startup/startup_stm32h745xx_CM7.s" or "CM4/Core/startup/startup_stm32h745xx_CM4.s".However, the build source path for the startup files in the mx-generated.cmake in each core's folder is ". /Startup/startup_stm32h745xx_CM7.s" or ". /Startup/startup_stm32h745xx_CM4.s".Therefore, the cmake file must be changed to build.

I have been trying to get VS Code working with the latest STM32 VS Code plugins, and not having much luck. Latest plugins installed, on a nice fresh install of Fedora Desktop Linux.I have been using Red Hat/Fedora/CentOS, Ubuntu and versions of Mint and Arch as desktop OSes and development platforms since 1995...That being said, I was frustrated that I couldn't get this piece of the plugin puzzle working. The plugin could not find the Cube MX installation. So, I tried adding a .exe extension to it (yep, on Linux), and lo' and behold, there it was. Cube MX came to life.This tells me the plugins are coded to search for a .exe file extension by default.John

Hi, I'm trying to understand what filters I have to apply in CubeMX to find products that support 2 QUADSPI with independent clock. E.g. h7a3aii6q seems to be such part that allows me to have two independent  QUADSPI and there are parts like e.g. H743XIH6 that have QUADSPI Dual-Bank with two NCS but with only 1 Clock and there are also Parts with OCTOSPI, but they don't seem to have two independent interfaces most of them time.Any chance to make part search easier for me to find products that have features like these two independent QUADSPI?Thx

In the H562 CubeMx setting the flash option bytes only allows flash number of sectors up to 7. If you look at the FLASH_EDATA_EraseProgram example in the H5 firmware bundle you will see it sets the number of sectors to 8 before calling FLASH_OB_EDATAConfig function. this function decrements by one before ORing the sector enable bits. Because CubeMx only allows up to seven when it generates code you do not get the full EDATA range. And if you set 1 in cubemx I guess you do not get any??? 

I have started a new project using STM32H573. This is using the following:Cube MX 6.16Cube IDE 2.0 - Build: 26820_20251114_1348 (UTC)The project has secure zone enabled. I have written bare metal code and shown I can run/debug code in the non-secure environment without issues, and I can invoke non-secure callable functions etc.My problem comes when I add Free RTOS and enable CMSIS RTOS v2 to the non-secure side.When I build, I get linker errors (see below).When I search the forums, there have been similar issues raised, but most are quite old posts or seem overly complex (which always worries me)``C:/Users/531023/git/TEML20/Monitor/NonSecure/Debug/../Core/Src/app_freertos.c:86:(.text.MX_FREERTOS_Init+0xa): undefined reference to `osThreadNew' C:/ST/STM32CubeIDE_1.18.0/STM32CubeID

So here is a weird thing I've noticed with a STM32U073... CubeMX shows that this CPU has the "Trace Asynchronous SW" option, but for this mcu it is no longer listed under SYS, but under its own category: "Trace and Debug" -> "DEBUG". Anyway, after enabling it, the signal shows up on the graphical pinout, with the name "DEBUG_JTDO-SWO". This is pretty much the same as i was used to with other STM32 mcu's. So when i was designing a PCB for this new STM32U073 MCU i assumed it had support for SWO (or SWV or whatever the name is). But now when I'm trying to debug this MCU, the debugger doesn't allow me to enable "Serial Wire Viewer (SWV)" in the debug configuration properties of STM32CubeIDE. The option is just greyed out. So I did some more digging in the datasheet for the STM32U0, and I'm starting to wonder if it even has support for SWO/SWV?  Can anyone enlighten me? Is this just a problem with the debug config in STM32CubeIDE, or does the&n

STM32Cube MCU Package for STM32U0 Series 1.3.0  + STM32CubeMX 6.15.0 + STM32U083RCT6You can configure the SWO output in the configurator (CubeMX), but in fact, SWO is not present in the microcontroller. 

Hi I am using STM32H7S78-DK.I don't understand how to use the compare tool in cube mx project.My project consists boot and application software, i.e., a total of four different software versions. Which software does the compare tool compare? How can I select the software?