Product forums

Hi, I am experiencing a technical issue with the ST 16GZMAI camera when connected to the EVK-U0I1 control board. While the system works fine with my 55G1MBI1 camera, the EVK GS 1.1.2 GUI fails to recognize this specific model and displays the following error: "Error: could not broadcast input array from shape (341,280) into shape (340,280)" I am also unable to change the detector format. Could you please refer me to a technical expert who can assist with the configuration of this model? Best regards, Sean

Hello everyone,I am working on my bachelor thesis about sensorless Field-Oriented Control (FOC) for a three-phase BLDC motor.At the moment, I have a NUCLEO-F303RE board, a small BLDC motor, an ESC, and a power supply. I have already generated and measured PWM/SPWM signals from TIM1 channels on the STM32, but I understand that using an ESC with a 50 Hz throttle signal is not the same as directly generating three-phase PWM for FOC.For this reason, I am considering using an X-NUCLEO-IHM07M1 motor driver expansion board with my NUCLEO-F303RE board.My question is:Can the NUCLEO-F303RE + X-NUCLEO-IHM07M1 combination be used for a sensorless FOC thesis project? More specifically, can this board act as the required three-phase motor driver/inverter stage so that I can implement or test sensorless FOC with STM32 Motor Control SDK or m

Hi everybody.I'm currently trying to use the N6 Nucleo for a personal application but am having trouble starting the debugger after initially successes. I am using the Nx_TCP_Echo_Server example, and after a couple of successful iterations my debugger stopped working entirely.I am using the VSCode extension. When I start my debug session with ST-Link GDB server it will connect to the debugger, but an error will follow in the terminal as shown ("target not responding"). After disconnecting and re-initializing the debugger I will get the following error ("error in intializing... please check power"). I get the same issues after power-cycling the board. LED 2 (Red) will then remain off until I power cycle the board after the first error.

Device: NUCLEO-N657X0-Q Board Environment: STM32CubeIDE for Visual Studio Code Extension (v3.9.0) Description & Symptoms: The debugger loses a connection with the board with “Target not responding” and “Unable to read memory” errors.  Reverting to version v3.8.0 of the extension and all of its dependencies resolves the issue. Steps to Reproduce:Set a breakpoint on the first line of the FSBL Reset_HandlerRun the debuggerStep past the following line in the Reset_Handler: mov sp, r0 Expected Behavior: Debugger is able to continue stepping through the code Actual Behavior:

Due to absence of a security forum for MPU's (while there is for MCU's) posting this here.The CRA prohibits products with known CVE to be placed or made available on the EU market.The ST Yocto ECO 6. Scrarthgap currently has 632C CVEs. The latetst Yocto master has 13.As such,1. how to place a product on the market while a distro without known CVE's does not exist ? A company may have great documentation and processes but if the actual supplied software has known CVE's there isn't a to place it on the market2 Many devices may use even older  ECO systems (5.10) images which may have even more CVE. How will there get patched ?3. Where can information about the known CVE's in ST kernel , U-Boot, OPTEE and TF-A (dev packages) be found ?

Hi everyone, I’d like to ask for your expertise. I’m working with a custom board based on the STM32H755ZIT, configured in LDO mode. My issue is that when I connect the board to my PC via USB to use the Virtual COM Port (VCP), the computer does not detect the device. I haven’t encountered this problem on other boards I’ve used, such as those with STM32L4 or STM32WB, where USB VCP works as expected. Is there a particular difference in the USB VCP implementation between the STM32H7 series and the STM32L4/WB series that I should be aware of? Here is the noteworthy configuration of my project in CubeMX RCC, HSE=Crystal/Ceramic Resonator SupplySource = PWR_LDO_Supply (This is in line with my hardware design) Power Regulator Voltage Scale = Scale 2 USB_OTG_FS,Mode=Device_Only USB_DEVICE_M7, Class For FS IP = Communication Device Class (Virtual Port Com)   For the code:

Hello,I am working with the B-L4S5I-IOT-01A board (MCU: STM32L4S5VIT6) and attempting to load a .hex file using the UART bootloader via USART1 (PB6, PB7).Since this USART is connected by default to the ST-LINK interface, I removed the necessary resistors (R42, R43) to isolate the ST-LINK connection. I then provided direct RX/TX connections from the MCU side through the corresponding pads.However, I am unable to detect the MCU UART in the STM32 Programmer IDE. The device does not appear or respond during the bootloader communication attempt.Could you please guide me on the correct procedure to:Properly enable UART boot mode on this board

i created a project with the MCSDK for controlling my 3-phase motor,i used it to create a new project with the ioc file with the cubemx, but got many compilation errors, i manage to solve lots of them but got 1 error i cant solve:error: #error "Please select first the target STM32G0xx device used in your application (in stm32g0xx.h file)"133 | #error "Please select first the target STM32G0xx device used in your application (in stm32g0xx.h file)" but the macro STM32G031xx is defined on my PREPROCESSOR definitations. There are lots of issues with the last third-part parties software lately (MCSDK and GFX as well), the projects are lucking some folders, like the include folder in which the main.h exist or the h files of the drivers and are not part of the project when doing searches 

Hello group,I'm a humble hardware guy integrating the LSM6DSV16X into a robotic application.We are going to use it in control loops, between 3kHz and 5kHz sampling.Between the main mode and the OIS mode, there are tons of ODR to choose from.However, is there a way to make the ADC sample at EXACTLY 5kHz?? Like a triggered or synced ODR?Or do I have to set the ODR at 7.68kHz and read the latest value from the FIFO and deal with the small discontinuities?I see the Triggered-ODR section 6.6 in the datasheet. Does it means enabling this will sync the ADC with an external INT2 pulses? Does the new values appears in the FIFO after a defined short delay?Thanks!

Hello everyone,this is my first time building an STM32 Based Board myself.I am trying to talk to the Chip Using a CP2102 UART Bridge connected to PA9 & 10.For Reset and Boot 0 ive connected Reset (NRST) to RTS of the UART Bridge and Boot0 to its GPIO0 Pin and configured that Pin in the Bridge. I have however also tried just pulling Boot0 High and Jumping NRST to GND and then immediately connecting using STM32CubeProgrammer.Using an Oscilloscope ive found that the Magic Packet is sent to the STM32 (0x7F, 115200 Baud, Even Parity, 1 Stop) but there is no response (Tx of the STM32 stays high all the Time).PB15 is left floating, I am using the VIT6 Variant (The LQFP100 Package), its a Brand new Chip, is there any configuration required before this works?

Hi,first time TouchGFX user but not new to graphics programming and hoping to get some help understanding a TouchGFX problem I'm having on a Riverdi RVT50HQSNWC01-B I'm thinking of using for an automotive dashboard display.If I don't throttle my display changes, the display buffers don't have the same content. The buffer with the most complete looking content does have a small glitch towards the bottom right hand side of the RPM segmented display, so I'm guessing it's not as simple as TouchGFX didn't get around to doing all updates on both buffers but more like it ran out of space somewhere to manage the updates? I've tried putting invalidate()'s either side of making changes, as suggested in this (https://community.st.com/t5/stm32-mcus-touchgfx-and-gui/double-buffer-one-buffer-is-not-updated/m-p/165271#M9822) thread, but that d

Dear Sir or Madam,  We would like to use NUCLEO-WL33CC2 to verify DMR RSSI reliable detection(compulsory requirement) and demodulation(optional requirement).  We only need rx chain for scanning purpose.  As per ETSI TS 102 361-1, DMR TDMA frame has sync word in the middle of 30ms frame and does not have preamble. And in Chapter 10.2.2.2 (Physical layer), an RRC filter is designed for 4FSK.  It seems these settings may not have corresponding option in STMWiseCube, so that we would like double check with you if there is any better setting for detect 30ms packet RSSI at least.  We do know the sync word content for DMR, which is 48 bit long. The modulation is 4FSK, nomial channel width is 12.5kHz, and data rate is 9.6kbps. And deviation is +/-0.648kHz and +/- 1.944kHz for 4FSK, shall we use 1.944kHz in the setting of deviation in STMWiseCube?   Our requirement is RSSI at room temperature for this TDMA fra

When using a Zephyr RTOS host with PAwR synchronization response enabled, the STM32WB09 controller (observer role) reports a legacy LE Periodic Advertising Report (subevent 0x0F) while syncing to a PAwR broadcaster.The broadcaster is implemented on EFR32BG42 (SiLabs). Zephyr host reports:[00:00:02.987,453] <dbg> bt_hci_core: hci_event: event 0x3e[00:00:02.987,480] <dbg> bt_hci_core: hci_le_meta_event: subevent 0x0f[00:00:02.987,497] <err> bt_scan: The controller shall raise the latest unmasked version of the eventWhich corresponds to:LE Meta EventLE Periodic Advertising Report (legacy) The Zephyr BLE controller layer is based on stm32wb0x_ble_stack_controller_only.aDoes stm32wb0x_ble_stack_controller_only.a support:BLE 5.4 PAwR (Period

I am looking for an EEPROM device that has the UID but also supports the 256-byte identification page.I was lead to believe that densities less than 1M support either/or, but greaterthan/equal to 1M does support both.However, from what I can tell from the datasheet(s), the -F version (M24M01E-F) says: "The device offers an additional 256-byte page, called the identification page. This page can be used to store sensitive application parameters, which can later be permanently locked in read-only mode."But the -F version does not have section 4.5 so it does not have UID.  datasheet for version -U (M24M01E-U) says "The device also offers an additional 256-byte identification page. This page stores a 128‑bit (16‑byte) unique factory-programmed serial number, locked in read-only mode at factory delivery."And in section 4.4 says "This is an additional 256-byte page, permanently locked in read-only mode. The us

Hello,   in an earlier post it was suggested to reset the FDCAN for full error recovery using RCC_APBRSTR1.FDCANRST Bit This bit seems to be global for all FDCAN instances. Is it correct that full error recovery in one FDCAN instance is not possible without interrupting traffic in the other instance - as all (or both in case of stm32g0b1) instances have to be reset?   t

Hello,I'm having an issue for a few latest versions of clangd. I was hoping this issue would be resolved in newest update of VS Code extension - clangd v1.0.5., but still with no success. Issue: I'm using two Configurations in CMake -> Configure. Configurations are defined in CMakePresets.json like this:I'm using define as this:

Hello all, Split from this thread: I'm using an STM32U5G9 and I need to read files from a USB stick. I don't want to use ThreadX because I have to keep this application small. How can I achieve this if UsbX and FileX are supposed to be used only with ThreadX and not in standalone mode?   Thanks for your help. Best regards, Julien

Dear community,I am looking for help to have TFM ported for nucleo_u385rg_q so that I can build the tfm secure and non secure images and do a secure boot on this board. The closest board is b_u585i_iot02a which is a stm32u5 variant. But there are many low level code required for this in trusted-firmware-m repo. Is there a work done by someone that I can use for my work? Any pointers as to how to accomplish this. Thanks in advance for your support.

In an Edge AI audio project that I'm working on, there is SAI2 peripheral that stops audio transmission after a while when the AI algorithm in the while loop of the main.c has done some inferences.The AI algorithm code was generated with Cube AI Studio and, when STM32CubeAI_Studio_AI_Process() is commented, the SAI peripheral works normally without interruptions.The board used is a NUCLEO-N657X0-Q.The version of software used is:-ST Edge AI Core: version 4.0.0-STM32CubeIDE: version 2.0.0-Cube AI Studio: version 1.1.0I've tried to search on internet for a solution and there is no material concerning it! I've tried to ask for help in other posts, but nobody helped me. Can somebody try to explain why and find a solution? I'm desperate and I don't know what to do for my project but withdraw. 

Hi,How do I serve request Get Source Capabilities Extended? I'm using STM32G0B1 with a port configured as SRC.When a SINK sends the Get Source Capabilities Extended the STM PD library responds with 'Not Supported' and my code is not aware that this even did happen. Is there way to intercept and serve this request? At least the callback structure does not appear to have direct support for this. USBPD_DPM_ExtendedMessageReceived is never called. /* CAD callback definition */ static const USBPD_PE_C

A couple of weeks ago STM32Cube disappeared off my computer. I went a got the install file for the most recent version (2.1.1). Since I have installed this when I try to import an old project into the workspace or use MX to generate code when trying to configure the pin outs to start a new project it keep trying to import lots of additional projects giving prompts that the project is old, it will be removed the new version will be installed. It then tries to import the STM32072B_EVAL project and hangs up.All the projects I'm trying to work with at the moment are based on the NUCLEO-F413 board.These are the imported projects

Hello all,There might be a possible bug in HAL_UART_DeInit(). When calling HAL_UART_DeInit() when it is already initialized could lead to CPU starvation. Assume that an interrupt fires after calling __HAL_UART_DISABLE(huart); and before huart->Instance->CR1 = 0x0U; the interrupt is going to keep firing provided that some conditions are met. I was able to run a debug session and saw that only the interrupt was firing.From the ref. manual -> Note: If TE bit is reset and no transmission is on going, the TC bit is immediately set.This means that the TC bit is always going to be set and the interrupt is constantly going to fire regardless of clearing the TCF

Looking for something to try. I'm want to recover from a failed firmware update of an MLite-880 from Elecevolve after their their 1-click installer. Elecevolve suggested a manual install using the firmware binary and STM32CubeProgrammer. I can put the device in its "DFU FW update mode" and connect to the device from the STM32CubeProgrammer using USB. After connect, the log shows:08:45:07 : STM32CubeProgrammer API v2.22.0 | Windows-64Bits08:45:35 : Disconnected from device.08:46:01 : USB speed : Full Speed (12MBit/s)08:46:01 : Manuf. ID : MALAHITEAM08:46:01 : Product ID : Malahit-Lite DFU08:46:01 : SN : 305B376E313308:46:01 : DFU protocol: 1.108:46:01 : Board : --08:46:01 : IAP08:46:01 : UPLOADING ...08:46:01 : Size : 1024 Bytes08:46:01 : Address : 0x800000008:46:01 : Read progress:08:46:01 : Data read successfully08:46:01 : Time elapsed during the read operation is: 00:00:00.053Whe

is there a template for developing a custom bootloader that uses the lpuart?Has the application firmware the ability to trigger a bootloader state so I can upload the new application firmware into stm32g051g8?What are the changes that I have to do on the application firmware?Thank you all.

Hi everybody.I have a problem with my Arduino GIGA R1  + Giga Display shield, configured by CubeMX. I configured the external RAM and flash and it works fine. I also successfully configured TouchGFX.My only remaining problem is the startup of the board. When I power it up, it doesn't boot. Even the ST-Link can't see the MCU. I must start it with BOOT_O at 0 (there is a button on the board) and it enter in bootloader mode and the DFU connection works. I can then connect the programmer, flash the Arduino firmware and after that, I can program/debug via ST-Link, I can reset it it still working. I verified the BOOT_ADDRESS it's on the good memory and not changed by Arduino firmware. As it work under reset, I presume memories are well configured.I can't find what could prevent the core to start. Both core start well on reset (verified with onboard LEDs) but nothing happen on power on. Does anyone have an idea of what could fail&