STM32 MCUs

Hi, I am using the Nucleo-L552ZE-Q board. I use STM32CubeMX version 6.17.0 which appears to be the laters version. When generating code for SD card FAT FS using CubeMX i get "sd_disckio.c" file containing only stubs of the functions, without content (the stub functions just return error value/no_init value). In CubeMX i have done some fault finding steps already with no luck. I have configured SDMMC1 before enabling FATFS. I am staying with default values, exvcept clock divider (Currently using 8). I am using Mode "SD 4 wide bus" Under Middleware->FATFS i enable it for SD card. SOMMC instance is SDMMC1, BSP code none.  The rest is default values. FAT FS version in cubeMX is R0 12c I have tried investigating the options in CubeMC, but i cant spot anything wrong so far. I also tried starting from scratch with a new project in CubeMX, with the same result: sd_diskio.c  only contain stubs. Does anyone have

Hi,I want to create a pin-compatible board to X-NUCLEO-SRC1M1 to further explore USB-C charging, is there a STEP or DXF file available for this or any other X-NUCLEO board that has both the ST Morpho and Arduino UNO R3 connectors please?Kind regards,Al

Hi, I am using two rotary encoders on an STM32U5G9ZJT. Currently I have:- TIM8_CH1 and CH2 available- TIM3_CH3 and CH4 available I know that standard encoder mode uses CH1 and CH2. CubeMX shows options like:- Encoder Mode (with remap CH1/CH2)- Encoder Mode + Index (with remap CH1/CH2 + ETR) My encoders are simple mechanical rotary encoders. Question:Should I use "Encoder Mode with remap" to map CH3/CH4 to CH1/CH2,or is there any benefit to using "Encoder Mode + Index"?   Is there any difference, If I use "TIM8 in encoder mode" or "TIM3 encoder mode from remap" Thanks!

Hi everyone,I’m currently experimenting with the GPIO_IOToggle_TrustZone example using STM32 TrustZone.When I build and flash both the Secure and NonSecure firmware, everything works correctly: the LED toggles as expected, so the interaction between Secure and NonSecure worlds seems fine.However, I’m running into an issue with debugging:I can successfully debug the Secure projectbut I cannot seem to debug the NonSecure projectI am using STM32CubeIDE and I would like to understand how to properly configure the environment to be able to debug the NonSecure application as well.Specifically:Do I need a separat

COO DetailsTop Marking

Added "DHCP" in the title to give the context. Using an STM32H7S78-DK I try to set up the network to join an IPv4 network through DHCP. I did set up the board using CubeMX, standard configuration, MPU activated. FreeRTOS + LwIP Removed all other interfaces I don't need. Made sure the Ethernet clock shows 50MHz The LED's on the RJ45 start to blink (Orange LED blinks with packets exchanged) but I get no IP address. digging in the possibilities I added a simple routine to monitor the DHCP advancements. struct dhcp *dhcp_data = netif_dhcp_data(&gnetif); if (dhcp_data != NULL) { printf("[DHCP] State: %d, Retries: %d\r\n", dhcp_data->state, dhcp_data->tries); } this shows I get stuck in state 6: waiting for an ACK -> what could be behind this? can someone share an .ioc file that sets everything cor

 Hi @Community, I have previously posted the same issue , that i have been working on the STM32H723ZGT6 - Nucelo board on Ethernet LWIP to acheive TCP/IP without free RTOS, Im still facing the same issue that i cant ping the IP.I have tried the GITHUB of STM32CUBEH7 -> APPLICATION ->LWIP -> TCPSEREVR ECHO . Its working perfectly , but cant remake or reuse it due to some library issue , im in a middle of a development of a project. so i tried to take the tcp confing in the example code and reuse it , but that also failed So i tried to remake the all the linker script and searched various Youtube videos , but everything remained in  vain , ill share some screenshots of my configuration , can anybody help me with this , I previously seens several quries that facing the same issue , those who got resolved the issue kindly share your solution and approach with me.  

The WL series is great, but unfortunately there aren't any chips with more than 256KiB flash and 64KiB RAM. This appears to be a serious limitation for a SoC with LoRa connectivity.The value proposition of this series is that you pay for one package that provides both connectivity and compute, which is cheaper than paying for 2 separate ICs. I'm personally working on a project where this small memory is beginning to be an issue, and I might end up having to separate those ICs.It kind of seems strange to me that the G0 "entry-level" series comes with much more memory - up to 1MiB / 144KiB.Are there any plans to bring out WL series chips with more memory?Thanks

Hi, As per UM3610 « section 7.7 », a "Bootloader limitation" has been found in NUCLEO-WBA25CE1. Please refer to "Workaround" section if you are facing this limitation.

 I am using CUBEMX Version   6.10 STMCUBE IDE                        1.16.0FW version                               F7V1.17.0Enabled LWIP ETH With FREERTOS CMSIS2same settings did with cmsis version 1 it's working but with cmsis version2 NOT WorkingI configured on internal Timer TIM1 as soon as I connect Eth Cable program counter not reaching threads & Timer callback / TIM6(systick update).I checked in fault handlers it is not reaching here ETH State in eth handler is (READY STATE --> START STATE)Error code in eth handler is zero.Here I have attached my .ioc fileI have updated flash ld file as per repository code LWIP Debug Messages : netif: netma

Split from Transmit line stuck high on STM32F415 with MAX3232 - this is a new questionWhat ST board would you recommend? This is not really my realm. Thanks!

Hi!I'm building a device using a STM32U31xx, connected to a Network Chip via I²C (PB6/7) and 2 GPIOs for Reset and BOOT0 Pin. The intention is to have new firmware downloaded onto the network chip, and flash new firmware to the STM32U031 via the system bootloader.I power up the system to invoke a power up reset on the ST device, I immediately flash firmware and ask the chip after another reset cycle for the new firmware version to confirm the new firmware was flashed.The behavior I observe is the following:- if the STs Option Byte nBOOTSEL is 0, the process works just fine, very reliably.- if nBOOTSEL is 1, the process fails even if I mass erased the STs flash memory entirelyThis is contrary to my understanding of AN2606 Table 2, pattern 11, that states that the empty check should start the system bootloader no matter the state of nBOOTSEL bit or BOOT0pin.I intended to have the ST chip flashed on production without previous intervention into th

Hello,I am writing this because I am unable to enable the SAI on this development board. The strange thing is that I actually managed to enable it before and it was working correctly. However, while implementing another feature, I switched branches and worked on a different GitHub branch for some time. When I came back, I noticed that the SAI was no longer starting.At first, I thought I had made a mistake in a commit, so I created a completely new project where the only goal was to start the SAI. Even though I believe all the steps are configured correctly, the MCK clock never starts, and the MCKEN register bit never becomes enabled. I am attaching screenshots of the SAI registers below.

Hi everyone,I have published a small bare-metal USB-C Power Delivery sink example for STM32 MCUs with the built-in UCPD peripheral:https://github.com/robobtnet/stm32-usb-pd-baremetal-sinkThe goal is to keep it minimal and portable:- no FreeRTOS- no ST USB-PD middleware- only two core files: pd_bm.c and pd_bm.h- configurable sink profiles- starts from the highest configured voltage profile, then falls back to lower profiles- reports the selected PD contract through the APIThe current tested setup is NUCLEO-G474RE using UCPD1. I also added porting notes for STM32U5/GPDMA based on an STM32U575 test project.I would appreciate tests and feedback on other STM32 families or boards that include UCPD, especially:- STM32G0- STM32G4- STM32U5- STM32L5- boards using UCPD2

Hi all,I'm looking for recommendations on eMMC chips that are known to work reliably with the STM32H743 via SDMMC1 in 8-bit mode.I've gone through a number of threads here and put together what I've found so far:- Micron 4GB (MTFC4GACAJCN) — comes up often, though some posts mention HAL misreading certain CSD fields (appears cosmetic rather than functional)- Kingston 4GB — confirmed working with SDMMC1 + FatFS + FreeRTOS, corruption reports seem tied to FatFS rather than the chip itself- Samsung KLM series — functional but VCCQ voltage negotiation adds complexity- Kioxia THGBMDG5D1LBAIL — 153-ball WFBGA, eMMC 5.0, fewer reports but looks promisingHappy to keep things simple — 3.3V on both VCC and VCCQ, no need for HS200/HS400.Would love to hear from anyone who has had long-term success with a particular chip, or any that are worth avoiding. Any layout tips for the 153-ball WFBGA package are also welcome.

I'm using an STM32H7S78-DK with TouchGFX and FreeRTOS. I would like to limit the framerate of the target to 30fps but withouth reducing the LTDC frequency.Basically having the VSYNC fired at 30fpsI've already set the  ((touchgfx::HALSDL2*)&hal)->setVsyncInterval(33.333);In the simulatorIs there a way to force it on the target?

Is there any utility in the holes and silkscreen circles around the TFBGA225 on the NUCLEO-H7S3L8?  It appears to be the same pattern on the Discovery board, suggesting it might be for BGA placement or maybe a heatsink. Edited to put the image in-line for better visibility

Hello Team,We are using the internal SMPS configuration for the core power supply. However, the power-up sequence does not specify the timing requirements for the different stages.Could you please provide the timing details for the following? What should be the time duration for the PWR_ON signal to transition from low to high while VDD and VDDA18AON are rising (Step 1)?After PWR_ON goes high, what is the required time duration for VDDA18PMU / VDDSMPS to rise (Step 2)?What is the exact meaning and function of the SDEN signal?Are there any additional considerations or recommended guidelines to be followed during the power-up and power-down sequence? 

Hello, I am using an **STM32 NUCLEO-N657X0-Q** board with the **B-CAMS-IMX camera module**. Originally, the board was working correctly. In **DEV BOOT mode**, I loaded and ran my AI model, using the B-CAMS-IMX camera sold by ST. The board connected normally to my laptop, and I was able to confirm that the AI application was running correctly by viewing the camera output and the AI object detection result on my laptop. I also changed the BOOT pins and confirmed that the same AI application worked correctly in **Flash Boot mode** as well. After that, I wanted to test whether the board could run from an external power supply instead of being powered through ST-LINK. So I changed **CN9 from 1-2, STLK power, to 5-6, VIN power**, following the description in the official NUCLEO-N657X0-Q documentation. Then I applied **7V from a DC power supply to the VIN and GND pins** of the NUCLEO-N657X0-Q board. I carefully checked the polarity and connected VIN and GND corr

Hi, As per title I am unable to enter the System Memory bootloader when using the STM32C071FBP6N. Any assistance would be greatly appreciated. Following the notes in AN2606, i have configured pattern 11 (line 2) using the CubeProgrammer but when completing the reset with the Boot0 pin high it does not enter the bootloader mode and can tell this because my user application runs immediately after the reset occurs. I have been able to jump to the bootloader through my own firmware where I initialize the HAL and GPIOs and then check the status of the boot0 or other pins then manually change the PC and SP but wish to avoid this method as this should not be necessary. ------- I have followed the steps below: 1. Using a ST-Link I have successfully changed the option bits nBOOT_SEL=0; nBOOT1=1; nBOOT1=1; BOOT_LOCK=0 using the CubeProgrammer and have also flashed a basic UART output program which outputs to USART2 the whether the PA14

I am working on SDRAM execution using FMC on STM32H563ZI (NUCLEO-H563ZI board) with external SDRAM connected through FMC interface. Our target is: Execute application sections from SDRAM Place heap and stack in SDRAM Enable automatic scatter-loading/copy from internal flash to SDRAM during startup We are facing an issue where: SDRAM initialization appears successful Manual SDRAM read/write access works in application runtime But automatic copy/scatter-loading from Flash to SDRAM during startup is failing Application execution from SDRAM is unstable and leads to HardFault/reset handler Below are the detailed steps and observations. CURRENT STARTUP FLOW Reset_Handler→ SystemInit()→ PLL/System clock configuration→ FMC GPIO configuration→ FMC SDRAM initialization→ SDRAM command sequence→ __main(

Is it possible to use the awesome MDF and/or ADF on STM32U5 with input data from RAM? I have not found any configuration for BSMX for this. One use case is an high performance external delta-sigma-demodulator (ADC) on SPI with proprietary data format (24 Bit per channel, MSB first, CRC etc.) for providing the sound data. Another use case is an LSM6DSV16XTR, also connected via SPI.

Hi,I’m experiencing a consistent issue with the STM32 Motor Control SDK:The first motor start attempt always fails with a MC_SPEED_FDBK faultAfter acknowledging the fault, the second (or further) start attempts work perfectly Observations:During the first start, there is no audible motor movementCurrent signals (I_q_ref / I_q_meas) look misaligned or not properly regulatedAfter the first failed attempt, signals stabilize and the motor starts normallyThe MC state is initially IDLEFault reported: 0x0020 (MC_SPEED_FDBK)Observations:During the first start, there is no audible motor movementCurrent signals (I_q_ref / I_q_meas) look misaligned or not properly regulatedAfter the first failed attempt, signals stabil

Hello everyone! I have a problem with reterning ticks in line "measure_speed_rpm = speed_reference / LL_TIM_GetCounter(TIM2);". speed_reference is const variable and equals 15000000. When I looked at Serial Monitor, it's indicated: (picture)That's mean that LL_TIM_GetCounter(TIM2) returns '1' sometimes. Nothing in my code not calling void EXTI1_IRQHandler(void), except EXTI Interrupt. And the main question is - Why it reterns only '1'??? Not 2,3 e.t.c.Thank you for help! void

The STM32F415 transmit and receive lines are connected to the MAX3232 chip. The board also contains chips to control LEDs and read tokens, which are controlled by the STM32F415, and those functionalities work, but I am having issues with the RS-232 communication. I get nothing on the receiving end. When I hook up a scope to the transmit line for UART4 (pin 51) on the STM32 chip, it is always high (3.3 V) and nothing is transmitted. What could cause this issue?