Automotive MCUs

Last slot should be left unprogrammed.even slot context A,odd slot context b.i am not getting this point alone.

I used the stm application fot configuaring the Timer.1.first picture shows the timer is working for just 4 seconds but i want it to run continously i used the stm_lld_enable inside the for loop and it is not working i dont know why.

Hi all, I'm using SPC570S0DISP DEMO Board(SPC570S50E1) to lean how to config CAN's filter.And the attachment is my config and source code. In my config,i just want CAN ID 0x112 to interrupt fifo callback function.And then i get the data in callback function. But unfortunatelly,ID 0x112/0x200/0x312/0x400/0x512/0x600/0x712 can interrupt fifo callback also. So,can anyone help me correct my configuration and explain it?thanks.Jer.

-------------------------------------------------------------------------------------------------------------------- /* initialize CAN controller, setup timing, pin description, CAN mode ...*/ /* Select clock source for CAN first */ FLEXCAN_CTRL1 |= FLEXCAN_CLKSRC; /* Source --> quartz/bus clock */​ /* Enable CAN module */ FLEXCAN_MCR |= FLEXCAN_MCR_FRZ; FLEXCAN_MCR &= ~FLEXCAN_MCR_MDIS;  while((FLEXCAN_MCR_LPM_ACK & FLEXCAN_MCR)) {}--------------------------------------------------------------------------------------------------------------------​The SPC570S MCU fails to escape from CAN's lowpower mode (while(~) in the above code). ​This rarely happens, but it can not cleared by watchdog reset and is only released when power is completely shut off.​mode is DRUN, CAN clock is 40mhz, crystal is 8Mhz, and clock source is IRC.​

Hi,This is for SPC560Bxx. I need clarification on set address for bootloader and the 32-bit address that shall be mentioned on UART/CAN frame. There is one column in firmware updater component, where we are supported to choose it the set address, here 0x0010000 or 0x0018000, yes, it is mentioned in 28-bits. There shall be another address sent via UART/CAN line, in step 2 of boot process after valid password verification. I got bit confused here and would like to have a clarification on both its usage.So,What is the set address, we are speaking about in firmware updater component?What is the range of load address that can be used for SPC560B54L5? And this is a 32-bit address.Thanks for your time on helping me out.Regards,Prashanth

Is it possible to compile the application only with Gcc (free) so do not use GHS or Hightec and flash and run the compiled code?I can tolerate that this compiler is not efficient as those not free.

..

Goodmorning,    I've been using the STM32 MCUs for a while. Now I should start a safety critical project, nothing complicated, I just have to monitor a signal at precise time intervals and set some GPIO (an interrupt based on a timer and little else) but safety critical.Since the SPC5s are classified as safety critical MCUs, I wanted to understand if they could be suitable for this project.In particular, how do SPC5 differ from STM32? Whay SPC5 si a safety critical MCU?Knowing well the toolchain for STM32 (cubemx + Truestudio) how difficult would it be to switch to the toolchain for SPC5?Thanks in advance,  Federico.

For starting with development on SPC56ELxx what I need is:the discovery board : https://www.st.com/content/st_com/en/products/evaluation-tools/product-evaluation-tools/mcu-mpu-eval-tools/spc5-automotive-mcu-eval-tools/spc56l-discovery.htmlSPC5 Studio

Preferably free

with standard CAN in normal mode ..i find that example in spc studio difficult and hard to understand..

Dear All ,SPC5Studio updated components are available (56,57 on 58)more information on http://download.spc5studio.com/SPC58xHxx, Advanced GTM and USBTypeC credentials should be requested on credentials@spc5studio.comNew or updated componentsRLA 1.10.0   Support of SPC574S-DISP board with PIT demo application   SPC58: Buffered I/O support for serial driver   support software I2C implementation for SPC58xExx   I2C driver support timeout on read and write functions for SPC56x, SPC57x, SPC58x   I2C baud rate display for SPC56x, SPC57x, SPC58x   Freeze bit enabled for STM driver configuration for SPC56x, SPC57x, SPC58x

Hello Is there any specific reason behind putting this delay, if yes than what it is?I want to manage time in my application so i tried to reduce the delay but in that case I am not able to transmit data properly.below is the given function sd_lld_write(&SD1,CMD2,(uint16_t)(sizeof(CMD2)/sizeof(CMD2[0]))); osalThreadDelayMilliseconds(200);

i cant find way for install this driver, can anyone help me..i am newbie on SPC5

Hi,Kindly Refer the attachments.Can you figure am I doing something wrong on jump to application program? (refer main.c)Here, the code is flashed in address 0x00008000 as expected, but jump to application is not done. The flash area of the actual PIT program as well, starts from 0x00008000, so I presume, there shouldn't be a problem. (refer flash.pngBut the program counter points to 0x400003B0, which is a RAM area. (refer PC.png)Could you please help me in,Performing Jump to Application programRelocating vector table to point the interrupts to the application programBest Regards,Prashanth Mohan

IS The FreeRTOS™ Kernel also available for SPC5 architecture?

i have compiled adc application from examples, i dont know how to import program to my spc56el70l5-disp kit using spc5-udestk.can any one help me or point me in right direction.

Are there some seminars or introduction courses to Automotive SPC5 microprocessor in Italy?Thanks

No such document found on the SPC584B series pages

In few word my code is divided in layer, I'll expect to change only the driver layer adapting it to the new micro.

I am using SPC5Studio 5.8.1 with a SPC570S-DISP board. Following user manual instructions, I downloaded udestk-4-10-04-spc5-stk for using on board code downloader and debugger.I experienced a problem trying to cvonfigure debug settings because I cannot browse configuration files in UDE startup tab preventing me from using integrated tool.

Hello. I'm using SPC58EC-DISP Kit, SPC5Studio.I am writing a can communication program from the example.I want to know how to not use can receive filter.I want to All Packet Received.SPC58 Wizard Setting only Specified ID Received....

..