Product forums

Hi everyone! I'm working with the NFC07A1 board associated with the Nucleo L053R8, with the intention of being able to perform ADC readings. I configured everything(ADC, pin, NFC07A1, etc.) on CubeMx, and then, opened the generated file on CubeIde. After writing the code for reading the ADC in the main file, i tried to run it, but even though there were no errors in the code, the  "startup_stm32l053r8tx.s" tab opens by pointing to line 51 (as well as Reset_Handler: ldr r0, =_estack). Consequently, the values acquired via the ADC are not printed on the screen, but the only thing printed on the sreen is "welcome to x-cube-nfc7 example". Could you help me solve the problem?

I am trying to interface STM32U5G7VJT6 with MT25QL128A using OCTOSPI1 in Quad SPI mode, but I still cannot store/run TouchGFX assets from external flash memory. Current configuration: Memory Type: Micron Device Type: Flash Device Size: 24 Clock Prescaler: 2 Clock Mode: Low Sample Shifting: Half Cycle Wrap Size: Not Supported Delay Block: Bypassed Screenshot attached.Could someone please check if I missed any important configuration like memory-mapped mode, linker settings, TouchGFX asset location, BSP/init sequence, or MT25QL128A command setup?

Greetings.I'm a Linux user, I use Windows on a smaller notebook for tools like TouchGFX, but this is quite inconvenient.Is there any plan to release a Linux version of TouchGFX Designer?I saw in the documentation that there's a simulator and that it can even be used with Wine; I'll test it today, but it would be really good to have a native version.Link where I saw information about the simulator: https://support.touchgfx.com/docs/introduction/prerequisitesthanks

I have a TouchGFX (latest version) application using STM32H753 and an OLED with GRAM.  Runs under Threadx.I found the development process quite complex but had no problem eventually building the project with all the subsystems apparently working properly.BUT....The very simplest part of the task I cannot complete.  I want C code in a ThreadX Thread to initiate the redraw of the next frame in the single display buffer (after which the DMA would be initiated from the frame buffer to GRAM...).  I need to access the OSWrappers.hpp in order to provide "Vsync" to TouchGFX which I can't do from "C".  After days and days, I can assure you there is no apparent way to call the relevent C++ method from the C code within Threadx.  In other words there is no 'hook' on the "C" side to make the function call.  Any suggestions?None of the Google-search documentation on this subject makes any sense.Thank youGerry

Hello Team,We need to interface a CT with a microcontroller for current measurement. The required measurement range is 0.01 A to 60 A with a 10 mA resolution.Please find the attached block diagram for better understanding. We require the reference circuit for the blue highlighted section.Awaiting your response soon.Thank you in advance.Image placed in line for easier viewing:  

Looking through the STM32Cube codebase, I’ve noticed a fairly strange but thoroughly consistent coding style. Indentation size is 2 spaces, using space for indentation; bracing style is more similar to Allman’s style rather than K&R and 1TBS. Naming style is also uniform, using CamelCase for external identifiers such as functions, structure fields, and global variables; along with a bit of Hungarian notation here and there (for example, pTxBuffPtr).This style is mechanically consistent through STM32Cube firmwares, drivers (LL, HAL, and CMSIS), code generated by STM32CubeMX, and BSP drivers. Even example projects follow suit.Could STM employees please share with us some documentation or guideline regarding this coding style? Looking for something similar to the Linux Kernel Coding Style and the 

Moved from the STM32 MCUs forum - this has nothing to do with MCUsFor this circuit, how can I implement the tactile switch functionality using the dual-LED feature? Can any one explain how the circuit should be designed for a 28V input? I am unable Implement this LogicLike My requirement is 28V I am getting upto 42mA So This switch Should Receive and that will be working like the Tactile and need to Glow the Once pressed one will glow if anoother Press other LED should Glow . How to Implement This Logic please reply fast 

I am working on converting projects from STM32F745VET to STM32U575VGT. Part of the startup routine of the projects is checking for flash errors using the CRC peripheral. The STM32F7 projects initialize a DMA channel in the following way: void MX_DMA_Init(void) { /* DMA controller clock enable */ __HAL_RCC_DMA1_CLK_ENABLE(); __HAL_RCC_DMA2_CLK_ENABLE(); /* Configure DMA request hdma_memtomem_dma2_stream1 on DMA2_Stream1 */ hdma_memtomem_dma2_stream1.Instance = DMA2_Stream1; hdma_memtomem_dma2_stream1.Init.Channel = DMA_CHANNEL_0; hdma_memtomem_dma2_stream1.Init.Direction = DMA_MEMORY_TO_MEMORY; hdma_memtomem_dma2_stream1.Init.PeriphInc = DMA_PINC_ENABLE; hdma_memtomem_dma2_stream1.Init.MemInc = DMA_MINC_DISABLE; hdma_memtomem_dma2_stream1.Init.PeriphDataAlignment = DMA_PDATAALIGN_WORD; hdma_memtomem_dma2_stream1.Init.MemDataAlignment = DMA_MDATAALIGN_WORD; hdma_memtomem_dma2_stream1.Init.Mode = DMA_NORMAL; hdma_memtomem_dma2_stream1

ST moderator: post split from this thread. Hello mƎALLEm, Thank you for your confirmation on this issue. I would like to provide some additional information. I have also encountered the same problem on the STM32F405RGT6. In STM32CubeMX, when I configure both HSE or LSE to "Bypass Clock Source" mode, the tool insists on reserving PH1 (OSC_OUT) or PC15 (OSC32_OUT) as RCC pins. It blocks me from configuring them as regular GPIOs, even though the hardware (as you've confirmed) supports it.

Hi there, im using Nucleo-F446RE , ST HAL and CubeMX, and im learning to configure the clockI use HSE Bypass mode (MCO from the st-link in the nucleo), everything perfect hereIn the RM i found out that, when using HSE BYPASS mode, PH1 (OSC_OU) should be left in HI-Z state What does HI-Z means in STM32 MCUs? does it mean configuring the pin as digital input? or it means configuring the pin as analog input?Or it depends?   When selecting HSE BYPASS MODE the chip image in the .ioc file gets set like thi

Here are the logs and waveforms. The slave device of IIC is unable to raise the SCL response. The data cannot be sent out either. The code is provided in the attachment.HAL_I2C_AddrCallback: 开始接收数据接收到字节[0]: 0x40接收到字节[1]: 0x03接收到字节[2]: 0x22接收到字节[3]: 0xFE接收到字节[4]: 0xBEHAL_I2C_ListenCpltCallback: 开始接收数据接收到字节[0]: 0x41HAL_I2C_ListenCpltCallback: 开始发送数据发送字节[0]: 0x05发送字节[1]: 0x62发送字节[2]: 0xFE发送字节[3]: 0xBE发送字节[4]: 0x30发送字节[5]: 0x31

Module / setup- Module: ST87M01-1301- Host: STM32-class MCU over UART, 115200 8N1, no flow control- Carrier: 1NCE NB-IoT (auto-PDP on CID 5)- AT manual reference: v3.1, 2025-10-06Current sleep-related configuration16:34:39.720 -> === AT readbacks ===16:34:39.720 -> >>> AT+CGMR16:34:39.720 -> <<< A:2.7.0-M:2.7.0-S:2.7.016:34:39.720 -> <<< OK16:34:39.720 -> >>> AT#SLEEPMODE?16:34:39.720 -> <<< #SLEEPMODE: 1,5,016:34:39.720 -> <<< OK16:34:39.720 -> >>> AT#WAKEUPEVENT?16:34:39.720 -> <<< #WAKEUPEVENT: 15,316:34:39.720 -> <<< OK16:34:39.720 -> >>> AT#SLEEPIND?16:34:39.720 -> <<< #SLEEPIND: 0C16:34:39.720 -> <<< OK16:34:39.720 -> >>> AT#RINGPIN?16:34:39.720 -> <<< #RINGPIN:0,20,1,

Dear ST,Now I'm testing my VL53L7CX sensor that is on the package P-NUCLEO-53L7A1 in Autonomous Mode with integration time = 2ms, ranging freq. = 4Hz and 4X4 Resolution, the attached screen-shot represents the output current related to my integration time and it's typically 2ms.My question is about the added peaks after the integration time peak, Why could this happen?and, How can I eliminate or reduce it?Knowing that the duration of these peaks illustrated in the other screen-shot attached.Thank you.    

Hello Team, We are currently investigating an issue related to the SPI communication between the STPM34 sensor and the STM32F4 microcontroller.At system startup, all values measured by the STPM34 remain stuck at zero. Even when voltage and current are injected using an OMICRON test bench, no measurement values are received or displayed.Several tests were performed:If we power up the system and confirm that the issue is present, then electrically restart only the board containing the STPM34, the communication recovers correctly and the measured values are no longer stuck at zero.We also soldered wires on one of the SPI buses (SPI1). Since there are two STPM34 devices on the board, two SPI instances are used to communicate with each sensor. The purpose was to verify whether the communication between the sensor and the STM32 was correctly established.Interestingly, simply soldering wires on this SPI bus makes the issue disap

Hello,I’m working on an STM32H757 (Cortex-M7 core, dual-core system) using SDMMC1 + FATFS (CubeMX-generated stack) and I consistently hit a blocking issue: Core issuef_mount() always returns:FR_NOT_READYor the execution breaks inside Error_Handler() depending on build/debug timing. Hardware / system contextMCU: STM32H757 (Cortex-M7, DCache enabled)SD interface: SDMMC1, 4-bit modeDMA: enabled (CubeMX SDMMC DMA configuration)External subsystem: Riverdi TFT display 12.1 inches (LTDC active)FATFS: CubeMX middleware (generic SD diskio template)No RTOS Software architectureSTM32CubeIDE latestHAL SDMMC driver (CubeMX generated)FATFS with sd_diskio.c DMA templateBSP

With the recent split of STM32CubeIDE and STM32CubeMX, I'd like to propose a dark mode option be added to STM32CubeMX.In consideration of the competing priorities for STM's software development team, I have two suggestions for how this proposal could be implemented:The first suggestion is the typical route: STM's in-house software development team add the UI theming and inputs to switch between dark and light mode.The second suggestion is less typical: make STM32CubeMX open source and let the larger software community assist with adding dark mode. Perhaps the source could be placed alongside other repositories in

Follow-on from STM32F030K6T6 microcontroller with Adafruit 2478 display and touchscreen.Hello all, i have a part of code for the touch screen for the 2478 display.I have found an example made with Arduino and i have adapted It for stm32, i would like to know if my code Is fine or It has some issues to fix and what u would suggest me to do. This part Is only for the touch controller of the display but i got several questions, like how many readings i should make from the ADC? rn i do and average basically.  #include "main.h" #include <stdint.h> /* ================= CONFIGURAZIONE ================= */ #define LCD_W 320 #define LCD_H 240 // PIN TOUCH (MODIFICA!) #define

Hi, We are planning to use STM32H743ZI for our project. Our requirement is to interface a 7-inch LCD touch display with 1024x600 resolution using a 24-bit RGB interface (RGB888) through LTDC. Can STM32H743ZI reliably support this display resolution? Also, what frame rate can realistically be achieved with this configuration? Are there any important hardware or performance considerations before selecting this MCU? Any suggestions or reference designs would be helpful. Thanks.

Hello There,I am currently trying to use the ST25R200 with the X-CUBE-NFC10 Software package.First thing am not sure about: In the "Software Packs Component Selector" I have to configure the "Board Extension NFC/NFC10A1" even when i don't plan to use this board. Otherwise i get a warning that "NFC10Boardlface" requires "NFC/NFC10A1". If I don't select the board part, I get a simmilar warning from the RFAL component.If i either don't add NFC/NFC10A1 in the component selector or don't select "Board Part NFC10Boardlface" in the Mode selection for the X-CUBE-NFC10 package, CubeMX seems to have problems ge

I am making use of the SWV to plot a 5Hz Sine Wave.The output on the plotter does not resemble a sine wave:Any recommendations to fix this?

I have created a firmware for a STM32L010F4Px microcontroller.I was able to Connect and Download Firmware by using ST-LINK V2.For some reason, I can't connect to the MCU at the moment by using CubeProgrammer + ST-LINK V2.Instead, I can connect/debug my microcontroller by using a SEGGER J-Link Ultra+ + J-Flash tool.The log from CubeProgrammer doesn't give me much details:13:28:34 : UR connection mode is defined with the HWrst reset mode13:28:34 : ST-LINK SN : 37FF71064E573436D2C1144313:28:34 : ST-LINK FW : V2J47S7

Hello!I am studying the SPC58NH92E7. My chose of MCU is driven by the need to have two Fast Ethernet transceivers operating simultaneously.I'm looking for baremetal (no OS) example for 100BASE-TX. Has anyone come across examples like this? I couldn't one among the standard examples in SPC5Studio without FreeRTOS.The standard approach in SPC5Studio is to use FreeRTOS. I have tried with FreeRTOS + RMII PHY. It's work correctly. Next step - baremetal application with ethernet promiscuous mode. I need to receive simple IPv4 UDP packets.And another question. Where can I find documentation for components/spc5_network_components_rla? "Generate SPC5 Application" doesn't generate any documentation for this. No "doc" folder inside "spc5_network_components_rla".

Dear Team,Could you please guide us on how to set the Linux terminal and SSH login password for the STM32MP257F series platform?We would appreciate it if you could share the required steps or documentation for configuring the password.

Dear ST,Now as you mentioned in VL53L7CX_ULD the Firmware is uploaded through the I2C protocol to the VL53L7CX every initialization in (Hex form) from the Buffers.h file as also it includes the default configurations for the VL53L7CX While I'm testing it in the Autonomous Mode with parameters integration time = 2ms, ranging freq. = 4Hz and 4X4 Resolution, making also the host board (NUCLEO-F401RE) in sleep mode which means that, there is no communication data on the I2C Bus.I found the current peak as illustrated in the screenshot attached, the first peak represents the integration time which is typically 2ms as configuration.Now I need a detailed explanation about the wave regions illustrated after the first peak and how can I minimize or eliminate them.As also I need to know how to update this firmware and if it has a datasheet or source code.Thank you

I'm working on STM32mp25f-EV1, i have downloaded FLASH-stm32mp2-openstlinux-6.6-yocto-scarthgap-mpu-v26.02.18 package but i'm facing problem while accessing SSH.