STM32CubeIDE (MCUs)

..

Hello all,after trying several attemts and hint's i am still confused what's wrong with my configuration or Board.Currently no slave is conected, i just wan't do display at least clock ans MOSIPlease have a look at the attached STM32Cube IDE Projekt.Let me know, where i have made the mistakes.Thanks in advanceMarc

Hi Community, I installed CubeIDE on two Windows 10 computers. In both cases there is no Intellisense. Does it have to enabled explicitly?

Hello . Why can not I download the firmware in STM32F103 to Stm32 CubeIDE. Although in STM32F407VE all is well. I'm flashing with ST-LINK.

Hi there,I have been using STM32CubeIDE for a few days now and really like it. I have managed to run some code and successfully debug my code using ST-LINK and the embedded debugger of STM32CubeIDE.I now would like to program my device so that the code remains permanently (i.e. do a "release" build and program/verify). I cannot find anywhere how I am supposed to do this.Can somebody help?Thanks!

Hi.I'd like to import an existing Atollic TrueSTUDIO project into the STM32CubeIDE. I select "Import...", then exactly "Import Atollic TrueSTUDIO project", specify a folder, but the "Import as" column shows "Convert 'System Workbench for STM32' project to STM32CubeIDE project". Importing the project as proposed produces the invalid orphaned configuration. How can I import the project correctly?

Hi Community, is there any way to make CubeIDE icons larger without causing fonts to appear blury?

..

I am using a NUCLEO-H743ZI board. Using STM32CubeMX, I was able to set SYSCLOCK to 400 MHz like so:With STM32CubeIDE, it won't allow me to do the same:What should I be doing here instead?STM32CubeIDE has been really frustrating.

I am on a windows 7 PC and used to work with MBED, then AC6 SW4STM32 without problem with an own made card with a L476RG mcu.I downloaded STM32IDE to test it, the installation ok without problem.I uploaded a very simple program called GPIO_IOT_toggled from examples. The building works fine. At the time to run the program, I choose "run as "local C/C++ application" (the only choice).A little window says:'Launching STM32L476RG_nucleo.elf has encountered a problem. Error starting process'When clicking on "details" I get:"Cannot run program "C:\Users\YPCU5336\STM32Cube\Repository\STM32Cube_FW_L4_V1.14.0\Projects\NUCLEO-L476RG\Examples\GPIO\GPIO_IOToggle\SW4STM32\STM32L476RG_NUCLEO\Debug\STM32L476RG_NUCLEO.elf": Launching failed"Can someone tell me if I missed some tuning in the STM32CubeIDE ?Thank you in advance

Hi there,we are using the STM32F303K8 with the NUCLEO-F303K8 board. I installed the latest STM32 Cube IDE v.1.0.0 and wanted to get the CAN bus working.So after searching for the latest documentation it took a while to figure out the new can bus implenentation. So as mentioned in "STM32L$ CAN new API and migration.pdf" my code looks like this:int main(void)   {   /* USER CODE BEGIN 1 */     /* USER CODE END 1 */       /* MCU Configuration--------------------------------------------------------*/     /* Reset of all peripherals, Initializes the Flash interface and the Systick. */   HAL_Init();     /* USER CODE BEGIN Init */     /* USER CODE END Init */     /* Configure the

I just installed STM32CubeIDE 1.0 version to give it a try. When I tried to enable SWV , i saw it is disabled and can not modifiable. At first, I assumed this is because of some limitation of chip, but with same hardware my other compiler ( Keil ) is perfectly using SWV and showing real time variables without stoping the code execution. Am I doing something wrong? How can I enable SWV?

After I click DEBUG ,it shows that Error in initializing ST-LINK device.Reason: No device found on target.I think it's not hardware's problem because I can download my program in Keil uvision successfully. and my debug configuration is showed as follows:​

I'm comparing against TrueStudio.Missing Subversive (and any version control system). Not a big deal to install from CommunityBigger deal is missing "Team Synchronize" perspective. I can't find a way to enable or download from Eclipse community. This makes this tool unusable to me.Once I install Subversive and check out TrueStudio project, it doesn't do an import, so project will not work. This is a nice to have. 

HiI generated code from STM32CubeIDE.I cannot use getchar() to get a charater from HyperTerminal.But I tied to use USART1->RDR. It can get a character as code below.char ReceiveAByteUART1 = '\0';printf("\fHardware: STM32L4 Discovery kit IoT node (B-L475E-IOT01A)r\n>");fflush(stdout);if(USART1->ISR & USART_ISR_RXNE) //Bit 5 RXNE: Read data register not empty{  ReceiveAByteUART1 = getchar();  putchar(ReceiveAByteUART1); // Display a character.  fflush(stdout);}But I can use above code on Keil uVision5.Could you help me to solve this problem?Thank you

I have an application, where I receive 4 sinusoidal signals simultaneously sampled through external ADC. Frequency range is 1 -1000KHz. I would like to plot these signals in cube32 IDE. My application is to detect the phase shift between signals ( in the order of -1-10 degrees) and correct them. Can I get accurate representation in cube32 IDE so that offsets and phase shift can be detected precisely?

STMCUBE IDE live expressions bug? or it is just cannot be that

Hi,I use the STM32CubeIDE to generate the code of STM32L4 Discovery kit IoT node (B-L475E-IOT01A) and I have added code to use printf command. I can send text to HyperTerminal except ">" as code below.printf("\fSTM32L4 Discovery kit IoT node (B-L475E-IOT01A)\r\n>");But I tried to use code below. It can send ">".uint8_t Text1[1] = {'>'};HAL_UART_Transmit(&huart1,Text1,1,100);Could you advise me to solve this problem?Thank you

Hi - I have a issue about debug mode by J-Link my MCU is STM32F030C8T6my debugger is J-Link OB ARM debugging emulatorthis my codeint main(void) { /* USER CODE BEGIN 1 */   /* USER CODE END 1 */   /* MCU Configuration--------------------------------------------------------*/   /* Reset of all peripherals, Initializes the Flash interface and the Systick. */ HAL_Init();   /* USER CODE BEGIN Init */   /* USER CODE END Init */   /* Configure the system clock */ SystemClock_Config();   /* USER CODE BEGIN SysInit */   /* USER CODE END SysInit */   /* Initialize all configured peripherals */ M

Hello , i need assitence on how to setup the clock settings on the nucleo board.Examples:What ware the settings for a system clock mspeed of 400Mhz (max) or 200 MHZThanks Marc

Hello,It would be nice if there was a external tools run field in the IDE just like in atollic - we always used that for flashing .hex files with segger j-flash.

I've searched the menus, and tried Google and the STM32CubeIDE's Help button and found nothing. How do I target the code to upload and run from RAM. I'm not using the CubeMX part if that's relevant - code is bare metal.