STM32 MCUs Software development tools

A new version of STM32CubeMonitor-RF has been released to fix some issues related to BLE OTA feature.The points covered by this release are :115533 and 117927 : During the OTA update, issue in the ACI_GAP_START_GENERAL_DISCOVERY_PROC command, change address type to public device address115760: During the OTA update, when Optimize MTU size box is checked, download is stopped after the exchange of MTU size. Set the OTA block size according to MTU size exchanged to increase speed. (need firmware 1.13.0)Download it on https://www.st.com/en/development-tools/stm32cubemonrf.html

STM32 B-U585I-IOT02A I am getting the below response in IDE when trying to run BLE_AT_CLIENT example in IDE, and not able to get the expected output, i.e Not able to find P2PSRV�? device. as mentioned in the readme file : readme: file:///C:/ST/en.stm32cubeu5_v1-1-0/STM32Cube_FW_U5_V1.1.0/Projects/B-U585I-IOT02A/Applications/BLE/BLE_AT_Client/readme.htmlFile download completeTime elapsed during download operation: 00:00:01.063Verifying ...Download verified successfully Debugger connection lost.Shutting down...Even the simple demonstration is not working ( file:///C:/ST/en.stm32cubeu5_v1-1-0/STM32Cube_FW_U5_V1.1.0/Projects/B-U585I-IOT02A/Demonstrations/IOT_HTTP_WebServer/readme.html ) The server is not responding. Please help me out with the solution.

I am using recently updated CUBEMX version 6.6.1As soon as i enable FreeRTOS cmss_v2 in cubeMX the USB init disappears...  MX_USB_DEVICE_Init is nowhere to be found........

I deleted CubeIDE and reinstalled the latest version 1.10.1, but it still doesn't work. The test environment was tested with NUCLEO-G071RB with the most basic code. Even if you delete and reset the RUN and DEBUG configration by referring here and there, only the warning as shown in the figure pops up. Thank you for your help.STMicroelectronics ST-LINK GDB server. Version 7.0.0Copyright (c) 2022, STMicroelectronics. All rights reserved.Starting server with the following options:    Persistent Mode: Disabled    LogFile Name: C:\Users\alko11110039\STM32CubeIDE\workspace_1.10.1\app\Debug\st-link_gdbserver_log.txt&nbs

Hello, I have the latest cubemx 6.6.1 installed.I created a simple project with only one SPI enabled, but cubemx stuck in  ''Generating user source code''.Attached is the log file in case your need. 

The attached simple project contains an ioc-files where the DFSDM peripheral is configured: channel 0 and channel 1; filter 0 for channel 0 and filter 1 for channel 1. In addition i have configured TIM6; but that's not relevant for the issue. This all is based on a real project; but i have narrowed it down to a minimum because only the code generation process is relevant.The issues are in generated file dfsdm.c in sub folder Src. After generation, the file contains two errors:The code between lines 43 and 67 MUST be executed after line 102. In other words: first the channel must be configured and THEN the filter. This is an old error ... maybe two years old or even more. I don't recall where i have read that the present order is wrong. But in order to make my application work, i need to swap the generated order.The statment "static uint32_t DFSDM1_Init = 0;" occurs twice: in line 119 and in line 175 causing build-error. This is an error which must have be

Im working on stm32f767 project. I designed my board. I want to upload&download my code. First step i need to take backup (download) my code after that creating a file (xml..?) to SD card. Also i want to upload code which in SD card to MCU. How can i do these?

Hello I'm using a stm32L431. here the documentation :https://www.st.com/en/microcontrollers-microprocessors/stm32l4x1.html#documentationHSI is enabled at 16MHz for USART2, used to receive a 1200Bd signal (7bit data + even parity + 1 stop).I receive wrong characters because of the trim. of parityI already asked a question about the TRIM but that's not the problemhttps://community.st.com/s/question/0D53W00001iwHrbSAE/how-to-trim-the-stm32-hsi-easilyI connect a USB converter (

Hello. I would like to understand a little bit more about the minimum stack and minimum heap parameters on the cube mx: I use stm32cubemx and stm32cubeIDE1.How can I see what is total available heap and stack memory2.Currently, I use Build Analyzer in stm32cubeIDE

As a project expands, scolling down the main.cpp file is slowing me down. So I wished to break down the main.cpp by selecting "Generate peripheral initialisation as a pair of '.c/.h'files" inside the ioc file-> project manager -> Code Generation ->Generated files. After compiling the generated code, the IDE shows:undefined reference to `MX_FREERTOS_Init()'make: *** [makefile:83: MX_FreeRTOS_test.elf] Error 1The same issue exsits in an empty project, and the issue would not appear if the project is converted to a C project. I noticed that other peripheral files such as usart has a pair of .c/.h file, whereas freertos only has a .c file been generated. in a C project. How can I fix this issue? Will this be fixed in later versions of cubeIDE?

Installation the last version on Windows 11 successfully, but starting programmer get error "Missing .. dependency, check Javal ...". Trying installation twice, got the same error info.

I am using STM32L031 for my project and since it is battery operated, I am planning to use Low Power Sleep mode for the same. And for that, I need clock below MSI range 1. So I chose to switch to 65kHz clock. But it gets stuck somewhere during clock configuration and because of watchdog, it resets the controller.Any idea how to fix this issue?here is my code to switch clock frequency and enter low power mode followed by clock_config functions: while (1) { HAL_IWDG_Refresh(&hiwdg); SystemClock_Config_65kHz(); HAL_SuspendTick(); HAL_PWR_EnterSLEEPMode(PWR_LOWPOWERREGULATOR_ON, PWR_SLEEPENTRY_WFI); SystemClock_Config_32MHz(); HAL_ResumeTick(); }32MHz clock configuration function:void SystemClock_Config_32MHz(void) { RCC_OscInitTypeDef RCC_OscInitStruct = {0}; RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};   /** Configure the main internal

Hi,I stay using stm32cubeIde and I need help to configure i2c pins to use bme/bmp280 to see data (results) in Terminal (Log)How to configure Terminal (Uart or other, I don't know) to see logs (results) of the bme/bmp280?

FP-CLD-AWS1 software package v3.0.1 for STWINKT1B fails to be compiled in higher STM32CubeIDE version than 1.8.0. Library link error happens. It is successfully compiled only in 1.8.0. version. It seems to be IDE bug. I hope it to be checked and fixed.

..

While trying to debug the program I get the following error:CM4 Failed to read all registersFAILED to REGISTER Values from the targetWhat should I do?

I bought this thing two days ago. I connected it to CubeIDE, it said "newer firmware", and... bricked. If I plug it into windows, CubeProgrammer will show the serial number(sometimes), but still won't connect. In Linus, STLink GUI can see and connect to it, but CubeProgrammer can't. I've already set BT0 high.Is my board bricked?

..

hi,i have questions about cubemx with stm32f seriesi'm testing the stm32f with cubemx + keil v5.26originally, i have created many projects using keil CMSIS Pack Installer with classic methodein this project, i can debug thread list on real time when i entered the debug modebut, after i have created a project using CubeMx with keil, i can't see the thread list and statusimage here..case 1: can see the thread list and status case 2: can't see the any information 

I'm looking to test an External Loader, so looking for guinea pigs.Had unsuccessfully tried to buy a couple of samples but none of the listing had any stock, or they wanted to quadruple the asking price.I'm interested in the extended parameters from READ-ID, trying to understand how it flags multi-die part, either as a die count, or die size. These have 4x the 256Mbit (32MB) die.Another example might be the N25Q512A that had 2x die

Failed to execute MI command:target remote localhost:61234Error message from debugger back end:localhost:61234: Connection timed out.

Hello,I am using the TIM2 with the STM32G041J6M6 and I am finding problems while enabling TIM2 using registersWith some code I have initiated the timer as reported below (TIM2 clock is enabled) While debugging I can edit some timer registers (ARR,PSC,CCR,SMCR...) directly in the SFRs tab of STM32IDE but not the CR1 and CR2 registers. If I put this line in my codeTIM2-> CR1|= (1<<0);At the end the TIM2 is not enabled and a mess appears on the corresponding output pin,the GPIOA MODER and RCC IOPAEN are affected and cannot be modified on-the-fly in the SFRs tab anymore.All this behaviour sounds weird to me....Any

I want to count external pulses for one second.On STM32F030 / HAL-Lib I did not findatomic read/reset countercapture by a second timer did not work, thoug I studied well and tested a lot how to config it by STM32CubeIDEIs there any example for a highly accurate count of external pulses by a tim (timers/capture/compare/pwm)?Thanx, Peter

Hi,I'm trying to get started with the STM32CubeIDE, but I'm unable to install the required st-stlink-server-1.2.0-3.pkg package (I'm on macOS Catalina). When I try, it fails with the following error message: "This package is incompatible with this version of macOS. The package is trying to install content to the system volume. Contact the software manufacturer for assistance." (see screen capture)So my question is: Is there a revised package coming out soon? Is there anything I can do in the meantime to start using the IDE (e.g. temporarily use an alternative to st-link)?Thank you for your time and support! A+Frank

Hello,I am working on NUCLEO-H7 board . Its dual core CM7 and CM4. When I Erase the full flash then I click into erase and programming option but I unable to add start address . The core M7 is get programming , but in Core M4 i unable to do programming because in start address block I unable to write . i am using latest version of cubeprogrammer.