STM32 MCUs

Hi Technical Support team,Platform: STM32H7B3I-EVAL board (MB1331-H7B3LIQ-D04)I want to understand memory and flash usage when we build and run any application using TouchGFX Designer  on STM32H7B3I-EVAL board. How to choose memory size and type for customized board based on STM32H7 Platform. ? How to choose specific SOC form STM32H7 family suitable for project requirements? Please refer below details.  On‑Chip (SoC: STM32H7B3LIH6Q)Flash: 2 MB internal FlashRAM (SRAM): 1.4 MB internal SRAM (split across multiple banks: DTCM, AXI SRAM, SRAM1/2/3):package: On‑Board External MemoriesOcto‑SPI NOR Flash: 512 Mbit (64 MB)

I'm debugging an STM32N647 on a custom board and running into a strange issue: the target silently drops the debug connection every time a breakpoint is hit or a single-step lands inside HAL_Delay(). Environment - MCU: STM32N647X0HXQ (Cortex-M55) - Debugger: ST-Link V2 - Debug mode: LRUN (code in AXI SRAM 0x34000000, running with XSPI/Flash boot) - Toolchain: VSCode + Cortex-Debug + ST-Link GDB Server - SWD freq: tried 400 kHz / 1 MHz / 4 MHz — same result - D-Cache: disabled (SCB_DisableDCache()) - Optimization: -O0 Symptoms 1. Download & run works fine — the firmware executes normally. 2. Setting a breakpoint → when the breakpoint hits, VSCode shows "Target disconnected" / "Lost debug connection". 3. Single-stepping into HAL_Delay() causes the same disconnect. 4. Reset via ST-Link sometimes recovers, sometimes requires power cycle. What I've checked / tried - Power supply is stable (measured with scope). - BOOT0/BOOT1 jumpers are correct for LRUN mode. - Tried lowering S

I set ETH to be working on RMII_PTP_SYNCHRO, However HAL_ETH_USE_PTP is still not defined by default.

Hello, I am using the RTC wakeup from the power standby example provided in the STM32C5 repository. The example starts the RTC wake-up timer and places the device in standby mode. The device does go to standby, and it does wake up due to the RTC wakeup interrupt; however, the RTC initialization fails after wakeup. It is worth mentioning that the only way I can get rid of this error is to power cycle the board.The failure happens in HAL_RTC_WAKEUP_SetConfig due to RTC_WaitSyncrhroWUTW() returning an error due to  RTC_CR_WUTE being set.static hal_status_t RTC_WaitSynchro_WUTW(void) { uint32_t tickstart; if (LL_RTC_IsActiveFlag_INIT() == 0U) { if (LL_RTC_WAKEUP_IsEnabled() == 1U) { return HAL_ERROR; // Code returns this error } t

G4 ref man says there is 1 (one) FDCAN peripheral:Yet when editing the IOC file I see 2 (two) FDCAN peripherals:I believe the ref man. What's with the IOC file editor?

Moved from MPUs forum.Hello,I have made a custom PCB with a STM32F756 and I'm trying to program this MPU through STlink. My main workstation runs Linux and I use stlink tools.To flash this MPU, I have connected ST-Linkv2 to my PCB (NRST, SWCLK, SWDIO, SWO, GND) and I can obtain a answer from MPU:hilbert:[~/zephyros/zephyr/samples/basic/blinky/src] > st-info --probe Found 1 stlink programmers version: V2J29S7 serial: 49FF69065050825521491967 flash: 1048576 (pagesize: 2048) sram: 327680 chipid: 0x449 dev-type: STM32F74x_F75x But I unable to flash a test program... I have tested with standard user or root.hilbert:[/usr/local/bin] > ./st-flash --debug --connect-under-reset write ~/cvs/firmware-europulse/build/zephyr/zephyr.bin 0x08000000 st-flash 1.8.0-121-g8c34a4e 2026-05-22T15:44:31 DEBUG c

I am using the Analog Devices EVAL-ADE9430 Evaluation board for testing one of their devices. The Evaluation board uses the NUCLEO-144 STM32F413ZH processor. I am using the Keil uVision development setup to run and debug code.  I am specifically concentrating on the SPI Bus Driver and the timing. I have no previous experience with STM Devices and how the SPI transfers happen in the processor.   While walking through the code and following it on my scope to see the SPI Bus timing I am seeing something that does not make sense.  The AFERead32BitBuffer() function is called when you read a 32-bit register from the SPI Device which is an Analog Devices ADE9430 Chip (see Below).  The code calls HAL_SPI_Transmit() with the number of bytes it needs to transmit (see line 9 below). In this case it is transmitting a two byte command header where bits [15:04

Hey,I have my images stored compressed (ARGB8888) on NAND flash accessed via FileX. Not memory mapped, so I need to cache everything before starting the GUI.I noticed this in the Bitmap API docs:Bitmap::decompress — "This method is called by Bitmap::cache when required."So does that mean I just implement BlockCopy with FileX, call Bitmap::cache(), and it handles the decompression automatically? Does it allocate for the uncompressed size and deal with the temp buffers internally?Would save me a lot of headache if that's the case;Thanks!

Hello, I hope you are doing well.I am currently working on benchmarking the Ethernet communication interface on an STM32H753 Nucleo board.My setup involves sending data from a Python script to the STM32, where the data is encrypted, and then sent back. This allows me to measure the RTT and overall throughput.I initially used Mongoose, but I encountered several issues:With UDP, I cannot reliably send more than ~1500 bytes, since larger packets get fragmented or dropped.TCP works correctly, but the throughput varies significantly depending on payload size. For example:~2.7 MiB/s for 1400-byte payloads~7 MiB/s for 10240-byte payloadsI would like to know:What is the best networking stack or library for STM32 to achieve better performance and properly handle UDP large payloads?Given that Ethernet is 100 Mbps in my case, I am not reaching near-theoretical throughput even without encrypti

Hi all,Hardware: Custom PCB, STM32H563ZGT6, USB powered.It was working fine but now gives me :Error: Cannot connect to access port 1!If you are trying to connect to a device with TrustZone enabled please try to connect with HotPlug mode. If you are trying to connect to a device which supports Debug Authentication with certificate or password, please open your device using it.Symptoms:- MCU gets hot to the touch within ~5–10 s of USB connect; cools instantly on unplug- VDD measures 3.29 V at the MCU pin- Chip is still functional: enumerates as STM32 Bootloader in DFU, ST-Link HotPlug connect succeeds, full erase + program + verify works- "Connect Under Reset" / normal connect frequently fails with Cannot connect to access port 1 or DEV_TARGET_NOT_HALTEDAlready tried:- Full chip erase via HotPlug → heat persists with empty flash- BOOT0 tied to VCC to force system memory bootloader

Hello Community,I am working on a custom board using the STM32 MCU (STM32WLE5JCI6). I am configuring the ADC with two channels:PB1 → ADC_IN5PB3 → ADC_IN2I performed the following test cases and observed unexpected ADC behavior.Test Case 1Applied VDD+ to Channel 2 (ADC_IN2)Channel 5 (ADC_IN5) connected to GNDObservation:Both ADC channels are reading 4095, even though Channel 5 is tied to GND.Test Case 2

Hello,I have been using the hrtim hardware on a prototype board with STM32G474RE and have noticed what might be a possible regression in CubeMX. Purpose:We are a group of students currently trying to develop FOC from scratch for controlling a BLDC-motor, this is a part of a bachelors thesis. As a part of developing the FOC we decided to use six-step commutation to start the motor before the FOC takes over. During the part of developing the commutation we have notice some strange behaviour between cubeMX versions.The problem:We are experiencing signal inversion with V6.17.0 of cubeMX with the exact same files pulled from the git repo. Either the migration fails for some reason or there is some sort of regression when it comes to the the configuration in CubeMX.6.16.1:HRTIM1 with slave-timers A,B,E are configured to output 6 PWM-signals with dead time configuration

Hi All,  In my application, I am using the STM32L451RCT6 and trying to configure COMP2 with the internal Vref as a reference (specifically 3/4 Vref). For some reason, it never worked. I was only able to get it working when using DAC_CH1 or an external source as the reference. After a few days of troubleshooting and research, I finally found a relevant block diagram along with an important note in the reference manual (page 532). The thing is, there are no mentions or explanations of this behavior in the reference manual, datasheet, or errata other than this. Could you confirm whether

I am using the Analog Devices EVAL-ADE9430 Evaluation board for testing one of their devices. The Evaluation board uses the NUCLEO-144 STM32F413ZH processor. I am using the Keil uVision development setup to run and debug code.  I am specifically concentrating on the SPI Bus Driver and the timing. I have no previous experience with STM Devices and how the SPI transfers happen in the processor. so I apologize a head of time. The Analog Devices ADE9430 uses a a 16-bit CRC (CRC-16-CCITT) and from what I originally read  the STM32F413ZH processor supports 32-Bit CRC (CRC-32-CCITT).  Diving deeper into the NUCLEO-144 STM32F413ZH processor manual section "29.4.2 CRC calculation" indicates "The SPI offers CRC8 or CRC16 calculation depending on the data format selected through the DFF bit." When the DFF bit (SPI_CR1 bit 11)

Hello, Can someone pls help me fill this information out for STM32H753VIH6? Thank you.      Model NameCheck Group１ (注１)２ (注２)３ (注３)４ (注５)Ministerial Ordinance Article Number第６条第一号イ第６条第一号ロ第６条第一号ハCheck ItemsPresence or Absence of Radiation-Hardened DesignDesign IntentRated Operating Temperature Range (°C) Whether or not compound semiconductors are used (Note 4)Maximum Clock Frequency (Note 4) (MHz)

I am having difficulties with initializing a SD Card.I am making use of the generated code to initialize the card:void MX_SDMMC1_SD_Init(void) I measured with a scope and I am getting 400KHz clock. All the pull-up resistors are correct and voltage is correct.Within the SD_PowerON() function, the function to send the MD8: SEND_IF_COND is called, but I get no response from the card. HAL Error Return is timeout.I tried a differ SD Card as well.Any suggestions where to start checking for potential issues?static uint32_t SD_PowerON(SD_HandleTypeDef *hsd) { __IO uint32_t count = 0U; uint32_t response = 0U; uint32_t validvoltage = 0U; uint32_t errorstate =0U; #if (USE_SD_TRANSCEIVER != 0U) uint32_t tickstart = HAL_GetTick(); #endif /* USE_S

Heyy, I'm using an STM32u545 (on a Nucleo board), and I'm trying to wake up my MCU from stop 2 mode using wake-up pin 2. Wake-up pin 2 is connected to LPTIM3 (via a jumper wire), and LPTIM3 works. Besides trying to wake up the CPU. An LPBAM application is collecting data using the ADC4 and LPDMA with LPTIM1. Also, it does work. But now I don't know how to wake the CPU using LPTIM3. Did I miss something, or is this not the way to go/ is there an easier way to do this? The program should: - read data on a specific frequency - wake up every two seconds to write the data to an SD card (eventually) Thanks in advance :) int main(void) { /* USER CODE BEGIN 1 */ /* USER CODE END 1 */ /* MCU Configuration--------------------------------------------------------*/ /* Reset of all peripherals, Initializes the Flash interface and the Systick. */ HAL_Init(); /* USER CODE BEGIN Init */ /* U

Hello,   ich set up my project with CubeMX for a CAN-FD (1 MBit/s / 4,8 MBit/s) and a Display for communication. Now i have the problem, that the SCK Signal for the communication looks more like a sawtooth signal than a rectangle. Also the SPI-Prescaler for the baud rate does not affect this signal. i am really confused. I need to use the 48 MHz HSE for my 4,8 MBit/s data phase for CAN-FD. I use an NUCLEO-C092RC and a LCD Display with ILI9341 (library from Mauro De Vecchi) Thanks for the help

Hello everyone,I'm using the stm32G0 USB Host with firmware package V1.6.3.There is an issue with H2D control transfers, where the USB Host stack send a second OUT packet before sending an IN packet on the last packet.I wrote a usb dfu host class that uses USBH_CtlReq.From this picture on the left we can see the PC sending a DNLOAD packet to the stm32h7, first the OUT packet followed by an IN packet.On the right we can see the stm32G0 host sending an OUT packet followed by another OUT packet, before sending an IN packet. The device here is the stm32f4, which for

Hello. Please check if there are any issues with the settings as shown below. PB4 : SPI1_miso PB3 : SPI1_sck PD6 : SPI1_mosi   Thank you.

MCU : STM32WLE5CCU6Firmware Package Name and Version : STM32Cube FW_WL V1.4.0Application : FUOTA using LoRaWANSetup : End Node(STM32WL) <===> Gateway(Dragino LPS8) <====> TTNHello, I am trying to get my LoRaWAN FUOTA example running for few days with unsuccessful attempts.At first i was successfully able to build LoRaWAN FUOTA application provided by ST under STM32Cube_FW_WL_V1.4.0. This firmware is made for NUCLEO-WL55JC(STM32WL55JC, Dual core with 256KB flash)But as i have STM32WLE5CCU6(Single core 256KB flash). With that also i tried to change the startup and linkers and updating .cproject with correct part number and was able to build it but while flashing gets an error.\STM32Cube\Repository\STM32Cube_FW_WL_V1.4.0\Projects\NUCLEO-WL55JC\Applications\LoRaWAN_FUOTA\Scripts\STM32CubeIDE> .\program.bat

Hello,I have a custom board based on the STM32U5A5 microcontroller. I am trying to run a fingerprint reader sensor over USB on this board. For this project, I am using USBX Azure RTOS.The configurations I made on the CubeMX side are as follows:High Speed Clock: Crystal/Ceramic ResonatorLPUART1 for UART communication:Mode: AsynchronousBaudrate: 115200 Bits/sPB10 -> LPUART1_RXPB11 -> LPUART1_TXUSB_OTG_HS Mode and Configuration:Internal HS PHY -> Host OnlyPA11 -> USB_OTG_HS_DMPA12 -> USB_OTG_HS_DPActive_VBUS -> DisableNVIC Settings -> USB OTG HS Global Interrupt: EnabledPA9 GPIO Output enabled for USB power (I verified that the device is powered correctly.)THREADX Mode and Configuration:Core: Enabled

Hi everyone. I have a problem with my U5A5ZJ-Q core board. The mounted microcontroller is STM32U5A5ZJT6QU. The project is to drive a QUECTEL em05 LTE modem. I need to configure the USB port exposed by PA11 and PA12 in Host mode. I am using the standard Host libraries in Middlewares and also the files in the USB_Host folder. I am trying to configure everything without success. I can't find exact written procedures to do this. Has anyone had problems? Has anyone tried? The problem is with the initialization of the USB Host port. It remains in reset mode and the CSRST bit never returns to 0. Below is a portion of the serial log that I printed on the monitor. " [CLK] Enabling HSI48...<CR><LF>[CLK] HSI48 RDY=1<CR><LF>[CLK] CLK48 <- HSI48 (via __HAL_RCC_CLK48_CONFIG)<CR><LF>[USBH] Init...<CR><LF>[LL] USBH_LL_Init (FS)<CR><LF>[HCD] Enter HAL_HCD_Init<CR><LF>[MSP] AFRH(GPIOA)=0x000

Original post: https://community.st.com/t5/stm32-mcus-products/stm32h7-flash-crc/td-p/887279 Github: https://github.com/STMicroelectronics/stm32h7xx-hal-driver/blob/1501be883dae6f202c1d3f856ee6b11407dc257d/Src/stm32h7xx_hal_flash_ex.c#L733 HAL_StatusTypeDef HAL_FLASHEx_ComputeCRC(FLASH_CRCInitTypeDef *pCRCInit, uint32_t *CRC_Result) { ... ... FLASH->CRCCR1 |= FLASH_CRCCR_CLEAN_CRC | pCRCInit->BurstSize | pCRCInit->TypeCRC; ... ... }​|= will not program the expected burst size if the reset value is not b00. It looks like on reset the value is b01 (16 flash word

Hi, During the development of a bare-metal driver for USB CDC (virtual com port) in device mode i noticed an unexpected behaviour when trying to configure the USB Core to do a transmission of a multi packet message. I've got the following code which prepares the transmission over usb for a data array "data" whose size is "dlen" over endpoint number "epNr". "epInBuffers" contain the pointers to the data buffers for each endpoint, "epInBytesTransferred" keep track of how many bytes have already been transmitted and "epInDataCntrs" the total amount of bytes to transmit. __RAMFUNC void prepareUSBTransfer(uint8_t epNr,const uint8_t*data,uint16_t dlen) { USB_OTG_INEndpointTypeDef * inEndpoint = ((USB_OTG_INEndpointTypeDef*)(USB2_OTG_FS_PERIPH_BASE + USB_OTG_IN_ENDPOINT_BASE + epNr*0x20)); uint32_t epCtrl = inEndpoint->DIEPCTL; uint16_t npackets; if(dlen==0) { npackets = 1; USB2_OTG_FS_DEVICE->DIEPEMPMSK &= ~