STM32CubeIDE (MCUs)

Hello!Then i've upgraded STM32CubeIDE v. 1.0.2 for macOS to v. 1.1.0, i can't load program to my Nucleo L476RG board. With v. 1.0.2 all works fine.Error: Data mismatch found at address 0x08000004 (byte = 0x75 instead of 0xA9).i tried to remove "Verify flash download" flag on Debug settings. After that, board becomes broken. Error: Device not found.How can i restore board?How can i fix flashing issue on v.1.1.0?P.S. Then i directly download v.1.1.0 .dmg file (not using "Check for updates") i get "Program corrupted - move to Trash" error after installation.Full log:STMicroelectronics ST-LINK GDB server. Version 5.3.2Copyright (c) 2019, STMicroelectronics. All rights reserved.Starting server with the following options:    Persistent Mode      : Disabled    Logging Level     &nbs

When I try to install STM32CubeIDE on my MacBook Pro, I get a message following verification that the application is damaged.I have re-downloaded several times with same result.

I'm facing a problem trying to format floating point numbers in STM32CubeIDE. The uC is STM32F103. I've checked the "use newlib-nano to print floating numbers" in the project settings.To narrow things down, I used the following code snippet to reproduce the error:char strP[100]; uint16_t cx = 0; cx = snprintf(strP, 100, "%6.2f, %6.2f, %6.2f, %6.2f", 0.0115697104, -0.0796313286, -0.0220388453, -0.111881733);The error doesn't appear on every iteration of the example code. It works most of the time, actually. When it fails, it prints:26815634999686289245754584189029181710324847797922429453525901675501503951146118153956426275383940846635237101275691881352391832390627762028461487571337216.00, 0.00, -0.00, 0.00"Or:0.00 2.00 0.00 2.00Things I tried to fix the problem:Increased the stack from 0x400 to 0x500 through STM32CubeIDE interface.Changed the linker scripts li

..

In the 'Check for Updates' portion of 'Help' there is a reference to updating the 'Available Software Sites preferences.' How do you set this to insure that the proper STM site is checked for updates?

Hi,I'm using STM32CubeIDE with a SEGGER J-Link connected to an STM32F7.I manage to flash and debug the board but I can't find how to attach the debugger to the target without resetting it.Thank you for your help.HG

Hi everybody!Have problem with building project, which is OK in TrueStudio. I have:Core/Inc/font24.o:(.rodata.Font24_Table+0x0): first defined herecollect2: error: ld returned 1 exit statusmake: *** [makefile:42: test3.elf] Error 1"make -j7 all" terminated with exit code 2. Build might be incomplete.15:42:59 Build Failed. 1 errors, 0 warnings. (took 151ms)Tried to solve the issue with Builder setting, but this settings is unavailable under MacOS Catalina /STM32CubeICECould you pls suggest any solution?RegardsEvgenii

You have hided most interesting pluigins Atollic has like RTOS avare debugging and hard fault analyzer. There is no J-Link support. All the easy avaiable views in atollic are now hidden. What is going on?

When trying to create a Debugger configuration for a project opened from sources + Makefile, STM32CubeIDE fails to create the configuration and shows the following error messages:" Not able to get board target."" An internal error has occurred. Update LCD"The project is using the STM32F405RGT6.How can I create this configuration and start debugging the project?Thanks

 Is there a document that has the exact procedure on how to import an example into the STM32CubeIDE?

I'm working with a STM32F4 Discovery (413) eval board and working through bringing the device up on Azure IoT hub through various mechanisms. I've successfully (the firmware does not like being talked to from a Mac serial port, i've only had success using Windows TeraTerm for the interactions) registered the device with shared keys, and CA Certificates. Next is to use the Device Provisioning Service (DPS). According to the readme.txt in the package By contrast to the direct X.509 authentication to the hub, the DPS allows the device to generate its own authentication certificate and to get it signed by the "test root CA" which is embedded in the HSM emulator of the Azure C SDK.I however do not see anything regarding any certificates anywhere in the code tree. Can someone point out where this might be found.

I would like to log this bug that concerns STM32CubeIDE.The CubeMX handles the scaling well, why not the IDE?https://community.st.com/s/question/0D50X0000BMGpgySQD/how-to-fix-stm32cubeide-very-small-on-4k-display

IAR Workbench has this:https://www.iar.com/iar-embedded-workbench/certified-tools-for-functional-safety/.and they assert compliance with IEC 62304.Of course it's good to comply with development standards when making the development tools themselves, but can anyone think of a situation in which this certification would be required?If such a situation exits and applies to the device I'm working on, I'm sure my company would be willing to pay for a certified version of STM32CubeIDE. Does this exist, or are there any plans for a certified edition in the future?--AndyC

Hello,I would like to use the ITM Printf directly inside a Console of STM32CubeIDE but It doesn't work on my side.I was able to display a character inside a "SWC ITM data Console" by using ITM_SendChar(). But I have the next issues:- For using printf, I read somewhere that I have to change the _write function inside syscalls.c like this:__attribute__((weak)) int _write(int file, char *ptr, int len) { int DataIdx;   for (DataIdx = 0; DataIdx < len; DataIdx++) { ITM_SendChar( *ptr++ ); } return len; }But even with this change, printf doesn't work.- It seems that it is mandatory to click on "Start Trace" on "SWV ITM Data Trace" each time I want to use the console display. So I have to do it every time I run a new debug session. There is a easy way to enable by default the "Start Trace " at each debug session?Thansk for your help.

Hello,I am trying to estimate initial SOC of battery by using a polynomial equation obtained from discharged voltage data of battery. I successfully run this polynomial equation in MATLAB but don't know how to write in STM32cubeIDE.The obtained polynomial equation is-p1 = 9.722*10^(-24); p2 = -1.565*10^(-19); p3 = 9.908*10^(-16); p4 = -3.139*10^(-12); p5 = 5.22*10^(-9); p6 =-4.318*10^(-6); p7 = 0.00127; p8 = 3.709; x=4; j = p1*(x.^7)+p2*(x.^6)+p3*(x.^5)+p4*(x.^4)+p5*(x.^3)+p6*(x.^2)+p7*(x)+p8 Here 'j' is polynomial equation and 'x' is initial voltage of battery.Thanks.

I'm new to FreeRTOS and STM32F4xx processors and therefore looking for some Sample FreeRTOS TCP/IP projects to aid my learning.RegardsNasir

..

I has a dev board and i sets some settings to fit the board.I wants it to be a temple.but i can't find a way to copy the project.is it having ways to do this in stm32cudeide 1.1.0?

When I use CMSIS RTOS I set a stack size of 128 words. Then the following code is generated: /* Create the thread(s) */   /* definition and creation of cmdHandlerTask */   const osThreadAttr_t cmdHandlerTask_attributes = {   .name = "cmdHandlerTask",   .priority = (osPriority_t) osPriorityNormal,   .stack_size = 128   };   cmdHandlerTaskHandle = osThreadNew(CmdHandlerTask, NULL, &cmdHandlerTask_attributes);When I read the documentation, the stack size in osThreadAttr_t is in bytes and the code seems to confirm this. Is this a bug or have I misunderstood it? (Im new to stm32 and this kind of low level programming so Im not too confident that I understood things right.) Can someone confirm or disprove my suspicion?Best,Anders

Since I have been having issues with some other efforts, I'm stepping back and creating a simple blinky test application. Everything builds fine, however when i use Debug, the upload failes with STMicroelectronics ST-LINK GDB server. Version 5.3.2 Copyright (c) 2019, STMicroelectronics. All rights reserved.   Starting server with the following options: Persistent Mode : Disabled Logging Level : 1 Listen Port Number : 61234 Status Refresh Delay : 15s Verbose Mode : Disabled SWD Debug : Enabled   Waiting for debugger connection... Debugger connected ------------------------------------------------------------------- STM32CubeProgrammer v2.2.0 -------------------------------------------------------------------       Log output file: /tmp/STM32CubeProgrammer_CRmk67.log ST-LINK SN : 066EFF505453707867193830 ST-LINK FW : V2J34M25 Voltage : 3.24V SWD freq : 4000 KHz Connect mode: Under Reset Reset mode : Hardware reset Cannot identify the d

HelloI am trying to debug a project in STM32CubeIDE v1.1.0.Debug probe: ST-LINK GDB server.I get this error:"Error in final launch sequence:Failed to execute MI command:target remote localhost: 61234Error message from debugger back end:Cannot access memory at address 0x4c05b508Failed to execute MI command:target remote localhost: 61234Error message from debugger back end:Cannot access memory at address 0x4c05b508Cannot access memory at address 0x4c05b508 "Is this issue known? How to solve it?I attach the debug log.

..

When I set a GPIO output level to high in the device configuration tool, it generates an LL_GPIO_SetOutputPin call on top just below the EnableClocks inside the MX_GPIO_Init function. This doesn't work. When I copy this call to the bottom of the generated function it works:static void MX_GPIO_Init(void) { LL_GPIO_InitTypeDef GPIO_InitStruct = {0};   /* GPIO Ports Clock Enable */ LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_GPIOC); LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_GPIOD); LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_GPIOA); LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_GPIOB);   /* * * * * * * * The generated calls below do not set the GPIOs * * * * * * * */   /**/ LL_GPIO_SetOutputPin(FW_INT_NRST_GPIO_Port, FW_INT_NRST_Pin);   /**/ LL_GPIO_SetOutputPin(SER_DATA_SEL_GPIO_Port, SER_DATA_SEL_Pin);   /**/ LL_GPIO_ResetOutputPin(MCU_GPIO0_GPIO_Port, MCU_GPIO0_Pin);   /* * * * * * * * The generated calls above do

..

I've been working on a project for a while (I2S based). I seem to have done something to confuse the IDE. Now when I try and debug, it says it's connected, but the Nucleo F722ZE is still running the previous firmware. The debug does not step into the first line of the code, as usual, and instead shows the call stack below.STM32_WM8731_Test.elf [cores: 0] Thread #1 [main] 1 [core: 0] (Running) I'm now unable to update the firmware on the board. I've tried reinstalling the IDE but I have the same issue.