STM32CubeIDE (MCUs)

Are support for STM32H745 or STM32H747 at STM32CubeIDE planned and when will it be available ?

I use STM32CubeIDE.l have one external input (ADC_IN8), the internal temperature as a second channel (ADC_IN17) and Vdd voltage as the third channel.void HAL_ADC_ConvCpltCallback(ADC_HandleTypeDef *hadc){   if (hadc->Instance == ADC1)   {      if (__HAL_ADC_GET_FLAG(hadc, ADC_FLAG_EOC))      {         ADC_raw[idx] = HAL_ADC_GetValue(&hadc1);         idx++;      }      if (__HAL_ADC_GET_FLAG(hadc, ADC_FLAG_EOS))      {         idx=0;         Vdd = (*VREFINT_CAL_ADDR)/ADC_raw[2];    &nbsp

how to erase or program using by st cube ide stm32f030k6t6 ? after I have program ic PA13 and PA14 set as input pin. now I can't erase or debug with stlink swd . please help thanks

Hi,I am using stm32 f407 for my project. I have set stack size min 0x6000. I am using STM Cube IDE. In one of the project files I have a float assignmentfloat val = resizedImage[i]; I have enabled FPU in the systemInit() function. I have set FPU_PRESENT and FPU_USED as 1. The following code excutes in SystemInit() function #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)  SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */  __DSB();  __ISB(); #endifI have selected floating point hardware implementation in project properties (-mfloat-abi==hard). The floating point unit is FPv4-SP-D16. However, there occurs a hardfault in the float val assignmemt code. The fault analyzer states "attempt to execute a coprocessor instruction".

I have two questions about the IDE:Is there a way to change the refresh rate of the variables in Live Expressions?Semihosting works only with OpenOCD. The problem with OpenOCD is that the Live Expressions doesn't work. Are you going to implement the semihosting for ST-Link GDB and/or Segger?

How to set the data breakpoint in STM32cubeIDE for DMA register access.

Hello,I am working on STM32G4 and used the STM32CubeMX and STM32IDE tools. After generating the code using the CubeMX and copying DSP libraries from CubeMX repository to project/Drivers folder, I encounter this error during compile: Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)Well, for this MCU, __FPU_PRESENT is already set to 1. But, Upon checking core_cm4.h, I noticed that SOFTFP is defined, and thus FPU_USED will be set to 0.Please let me know how to resolve the SOFTFP issue or is there anything I missed.#elif defined ( __GNUC__ ) #if defined (__VFP_FP__) || !defined(__SOFTFP__)  #if defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)   #define __FPU_USED    1U  #else   #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"&n

We encountered what appears to be a compiler bug as rewriting the code slightly by adding intermediate variables solved the issue.Relevant code :#define HT16K33_DISPLAY_NB_COLUMNS (8) #define HT16K33_DISPLAY_NB_ROWS (16) #define HT16K33_DISPLAY_NB_COLUMN_BYTES (HT16K33_DISPLAY_NB_ROWS/8) class HT16K33_SevenSegment { void writeASCII(const uint8_t ledPos, const char character);   private: uint8_t screen[HT16K33_DISPLAY_NB_COLUMNS*HT16K33_DISPLAY_NB_COLUMN_BYTES]; }   const char AlphaNum[] = { /* ... list of bytes ... */ };   void HT16K33_SevenSegment::writeASCII(const uint8_t ledPos, const char character) { assert(ledPos<3); assert(character<100); #if 1 screen[ledPos*HT16K33_DISPLAY_NB_COLUMN_BYTES] = AlphaNum[character-'0'-7]; #else { int charIdx=character-'0'-7; char charVal=AlphaNum[charIdx]; screen[ledPos*HT16K33_DISPLAY_NB_COLUMN_BYTES]=charVal; } #endif }In the above extract, the co

Hi everyoneI am getting desperate, I was able to add a few simple libraries to a project in cubeide, but I still fail to understand how the path for libraries are supposed to be added. Can anyone please direct me to a tutorial on how to add libraries.I am currently trying to add the VL53L0X API library to CubeIDE for my STM3F3.

I want to load a piece of software directly to the STM32H7 internal RAM. I precise that I don't want to load some code in Flash and copy it into Flash at runtime, I want to load directly to the part's RAM.I've linked my executable to map the function in RAM. I checked it is correctly mapped by readelf and I also converted the .elf to .hex to check manually that there is indeed some code located @ 0x24000000.When I load the .elf through STM32CubeProgrammer I can see that the RAm is correctly loaded.But when I load through STM32CubeIDE (by launching a debug session, using ST GDB server) the RAM is not loaded.Is there a setup I am missing ? Or is it a known limitation of the IDE or ST GDB server ?

Can't find any drop down menu or other pointer to this functionality in STM32CubeIDE v. 1.0.2. My stm32 device - STM32 F429ZI - Nucleo. Please, help me to solve the problem?

Hello, after a code regeneration due to ioc project changes I have to restore the language standard value (Project Setting > Tool Settings > MCU GCC Compiler > General) to GNU99 instead of default ISO C 99 or my project stop to build.The same probleam appers also with a new empty project generated by the Cube.

Hi, Through STM32CubeIDE I'm acquiring analogue signal, using STM32 F3 DISCOVERY.The converted values ​​are saved in a register, then I'd like to be able to read them on the screen through TERA TERM, but I can't activate the serial port. Can you tell me what the problem is please? 

I'm using both SPI1 and SPI2 on an STM32G071RBT Nucleo board, using STM32CubeIDE code generation and LL interface. Both SPIs are configured to use DMA for receive and transmit. SPI1 uses channels 2 & 3; SPI2 uses channels 4 & 5. The DMA transmit complete interrupt is enabled on the receive channels. (2 & 4).SPI1 works fine, but not SPI2!?!?! The SPI transaction is successfully started, and the data sent, but I never receive the channel 4 transfer complete interrupt. Any thoughts? Does the DMAMUX need to be configured to receive a channel 4 interrupt? (The interrupt handler is called "DMA1_Ch4_7_DMAMUX1_OVR_IRQHandler".)Thanks for any help.

I am debugging with STM32CubeIDE, and I have a problem in my program of something unrecognized writing in the memory space. To be more specific in the 0x20001FBCCould it be possible to define a breakpoint in the debugger that shoots when this memory space is overwritten?

I am using the STM32F303RE Nucleo, and STM32 CubeIDE. I have simple code that just sets up ADC1 in scan continuous mode, reading IN6, IN7, IN8, IN9 in single-ended, 12 bit size. I turned on the DMA for ADC1, using half word size, circular buffer.What happens is as soon as the main while loop starts the processor crashes, meaning I cannot step through the code anymore, and the code is stuck in the HardFault_Handler function in the stm32fxx_it.c file.Any suggestions welcome, this should be 101 for the CubeIDE. The main.c is included. Thanks for any ideas.../* USER CODE BEGIN Header */ /** ****************************************************************************** * @file : main.c * @brief : Main program body ****************************************************************************** * @attention * * <h2><center>© Copyright (c) 2019 STMicroelectronics. * All rights reserved.</center></h2> * * This soft

Hello there,I downloaded the STM32CubeIDE version 1.0.2 and tried to import a project from True Studio following File->Open Projects from File System... and selecting the directorie where my True Studio project is located.A dialog window opened asking me to select the best match for my MCU. After doing this, the same dialog window appeared again and again. Choosing OK or Cancel options result at the same and I cannot skip this window even using close button. I had to close STM32CubeIDE using the Windows Task Manager.The MCU I am using is STM32L433CCT6 and my operation system is Windows 10 version 1903.Could you please help me so

Hi! So, TrueSTUDIO supports the Eclipse Color Theme extension right out of the box.STM32CubeIDE instead does not, but not only: even after searching for it in the Marketplace, it does not show up. Why?I know that maybe this is not an high priority issue, but I think it is important for developer used to certain color schemes (expecially dark ones) to have them, if they have to migrate to a new IDE.

Some time ago I created a static library project in AC6 System Workbench for STM32. The project expanded and I started to adding build targets for more microcontrollers, STM32L, STM32F7, etc. After migrating the project to Cube IDE I am no longer able to select a target microcontroller in Build Targets configuration. I tried to create a separate static library project in Cube IDE directly but there is no option in New Project wizard to select the microcontroller. What is more, after completing the steps in the wizard I get this:I don't wont to start a new project in the end, if there is possibility I would like to add more configurations to my migrated static library project. How

When I started a debug-session, I got the following message:dyld: Library not loaded: /opt/local/lib/libusb-1.0.0.dylib Referenced from: /Applications/STM32CubeIDE.app/Contents/Eclipse/plugins/com.st.stm32cube.ide.mcu.externaltools.stlink-gdb-server.macos64_1.0.0.201904160814/tools/bin/native/mac_x64/libSTLinkUSBDriver.dylib Reason: image not foundAfter some days now, I could resolve the problem.The solution is homebrew!Please visit:https://www.reddit.com

What is going on here? @Markus GIRDLAND​ ?

..

I've just converted my project to C++ with STM32CubeIDE and now it gives me an error about a "undefined reference to `_gettimeofday'" in libc_nano.aHow do I fix this issue?

I am trying to work with photo diodes and need to measure 20mV or less with ADC. Whats the best resolution I can get with a single ended ADC (using ADC 3 channel 12 at the moment).Whats the measurement range on that channel? When we have less than 10mv, Is the ADC likely to give out a 0 value ?

Hi, We are looking to perform a firmware upgrade on STM32F413 where the firmware upgrade image is coming over BLE chip which is interfaced over UART to this controller. Can I know if any procedure was available to perform this operationRegardsSrikanth.